contiki/platform/remote
Antonio Lignan 330e450ba4 Zolertia Re-Mote platform ported to Contiki, developed whitin RERUM FP7 European project (grant #609094).
The port was done jointly by Zolertia and George Oikonomou (University of Bristol).
2015-05-29 22:04:43 +02:00
..
dev Zolertia Re-Mote platform ported to Contiki, developed whitin RERUM FP7 European project (grant #609094). 2015-05-29 22:04:43 +02:00
contiki-conf.h Zolertia Re-Mote platform ported to Contiki, developed whitin RERUM FP7 European project (grant #609094). 2015-05-29 22:04:43 +02:00
contiki-main.c Zolertia Re-Mote platform ported to Contiki, developed whitin RERUM FP7 European project (grant #609094). 2015-05-29 22:04:43 +02:00
Makefile.remote Zolertia Re-Mote platform ported to Contiki, developed whitin RERUM FP7 European project (grant #609094). 2015-05-29 22:04:43 +02:00
README.md Zolertia Re-Mote platform ported to Contiki, developed whitin RERUM FP7 European project (grant #609094). 2015-05-29 22:04:43 +02:00

Zolertia Re-Mote platform

The Re-Mote platform is a IoT Hardware development platform based on TI's CC2538 system on chip (SoC), featuring an ARM Cortex-M3 with 512KB flash, 32Kb RAM, double RF interface, and the following goodies:

  • ISM 2.4-GHz IEEE 802.15.4 & Zigbee compliant.
  • ISM 868-, 915-, 920-, 950-MHz ISM/SRD Band.
  • AES-128/256, SHA2 Hardware Encryption Engine.
  • ECC-128/256, RSA Hardware Acceleration Engine for Secure Key Exchange.
  • Power consumption down to 3uA using our shutdown mode.
  • Co-Processor to allow peripheral management, programming over BSL without requiring to press any button to enter bootloader mode.
  • Built-in battery charger (500mA), Energy Harvesting and Solar Panels to be connected to standards LiPo batteries.
  • Power input with wide range 2-26VDC.
  • Built-in TMP102 temperature sensor
  • Small form-factor (as the Z1 mote, half the size of an Arduino) 57x35 mm.

Port Features

The platform has the following key features:

  • Deep Sleep support with RAM retention for ultra-low energy consumption.
  • Native USB support (CDC-ACM). SLIP over UART for border routers is no longer a bottleneck.
  • DMA transfers for increased performance (RAM to/from RF, RAM to/from USB).
  • Shutdown mode controlled externally by the Co-processor, completely power the platform OFF, further reducing current consumption.

In terms of hardware support, the following drivers have been implemented:

  • CC2538 System-on-Chip:
    • Standard Cortex M3 peripherals (NVIC, SCB, SysTick)
    • Sleep Timer (underpins rtimers)
    • SysTick (underpins the platform clock and Contiki's timers infrastructure)
    • RF
    • UART
    • Watchdog (in watchdog mode)
    • USB (in CDC-ACM)
    • uDMA Controller (RAM to/from USB and RAM to/from RF)
    • Random number generator
    • Low Power Modes
    • General-Purpose Timers. NB: GPT0 is in use by the platform code, the remaining GPTs are available for application development.
    • ADC
    • LEDs
    • Buttons
    • Internal/external 2.4GHz antenna switch controllable by SW.
    • Built-in core temperature and battery sensor.
    • TMP102 temperature sensor driver.
  • CC1120 sub-1GHz radio interface:
    • Ported in Contiki, SPI based.
  • Micro-SD external storage:
    • Pending to port, SPI based.

Requirements

To start using Contiki, the following is required:

  • A toolchain to compile Contiki for the CC2538.
  • Drivers so that your OS can communicate with your hardware.
  • Software to upload images to the CC2538.

Install a Toolchain

Forked from platform/cc2538dk/README.md. The toolchain used to build contiki is arm-gcc, also used by other arm-based Contiki ports. If you are using Instant Contiki, you will have a version pre-installed in your system. To find out if this is the case, try this:

$ arm-none-eabi-gcc -v
Using built-in specs.
Target: arm-none-eabi
Configured with: /scratch/julian/lite-respin/eabi/src/gcc-4.3/configure
...
(skip)
...
Thread model: single
gcc version 4.3.2 (Sourcery G++ Lite 2008q3-66)

The platform is currently being used/tested with the following toolchains:

Drivers

The Re-Mote features a FTDI serial-to-USB module, the driver is commonly found in most OS, but if required it can be downloaded from http://www.ftdichip.com/Drivers/VCP.htm

For the CC2538EM (USB CDC-ACM)

The Re-Mote has built-in support for USB 2.0 USB, Vendor and Product IDs are the following:

  • VID 0x0451
  • PID 0x16C8

The implementation in Contiki is pure CDC-ACM: The Linux and OS X kernels know exactly what to do and drivers are not required.

On windows, you will need to provide a driver:

Device Enumerations

For the UART, serial line settings are 115200 8N1, no flow control.

Once all drivers have been installed correctly:

On windows, devices will appear as a virtual COM port.

On Linux and OS X, devices will appear under /dev/.

On OS X:

  • XDS backchannel: tty.usbserial-<serial number>
  • EM in CDC-ACM: tty.usbmodemf<X><ABC> (X a letter, ABC a number e.g. tty.usbmodemfd121)

On Linux:

  • Re-Mote over FTDI: ttyUSB1
  • Re-Mote over USB driver (in CDC-ACM): ttyACMn (n=0, 1, ....)

Software to Program the Nodes

The Re-Mote can be programmed via the jtag interface or via the serial boot loader on the chip.

  • On Windows:

    • Nodes can be programmed with TI's ArmProgConsole or the SmartRF Flash Programmer 2. The README should be self-explanatory. With ArmProgConsole, upload the file with a .bin extension. (jtag + serial)
    • Nodes can also be programmed via the serial boot loader in the cc2538. In tools/cc2538-bsl/ you can find cc2538-bsl.py this is a python script that can download firmware to your node via a serial connection. If you use this option you just need to make sure you have a working version of python installed. You can read the README in the same directory for more info. (serial)
  • On Linux:

    • Nodes can be programmed with TI's UniFlash tool. With UniFlash, use the file with .elf extension. (jtag + serial)
    • Nodes can also be programmed via the serial boot loader in the cc2538. No extra software needs to be installed. (serial)
  • On OSX:

    • The cc2538-bsl.py script in tools/cc2538-bsl/ is the only option. No extra software needs to be installed. (serial)

The file with a .remote extension is a copy of the .elf file.

Use the Port

The following examples are intended to work off-the-shelf:

  • Examples under examples/remote
  • MQTT example examples/cc2538dk/mqtt-demo
  • Border router: examples/ipv6/rpl-border-router
  • Webserver: examples/webserver-ipv6
  • CoAP example: examples/er-rest-example/

Build your First Examples

It is recommended to start with the remote-demo, it is a simple example that walkthroughs the platform features, such as the built-in sensors, LEDs, user button operation modes (press, release, hold-press), radio (Rime broadcast).

The Makefile.target includes the TARGET= argument, predefining which is the target platform to compile for, it is automatically included at compilation. To generate or override an existing one, you can run:

make TARGET=remote savetarget

Then you can just run make to compile an application, otherwise you will need to do make TARGET=remote.

If you want to upload the compiled firmware to a node via the serial boot loader you need first to either manually enable the boot loader, or just let the Co-Processor detect the flash sequence and do it on your behalf, as simple as not pressing anything at all!

Then use make remote-demo.upload PORT=/dev/ttyUSB1.

The PORT argument is used to specify in which port the device is connected, as we are currently using a dual-channel FTDI chip, at the moment the programming channel is always assigned to the second FTDI channel, so the FTDI will enumerate as /dev/ttyUSB0, /dev/ttyUSB1, and we would need to use the later one and specify when flashing using the cc2538-bsl script, as it will use the first port found by default. This will be improved in the next release.

To manually enable the boot loader, press the reset button on the board while holding the user button. (The boot loader backdoor needs to be enabled on the chip for this to work, see README in the tools/cc2538-bsl directory for more info)

To generate an assembly listing of the compiled firmware, run make remote-demo.lst. This may be useful for debugging or optimizing your application code. To intersperse the C source code within the assembly listing, you must instruct the compiler to include debugging information by adding CFLAGS += -g to the project Makefile and rebuild by running make clean remote-demo.lst.

Node IEEE/RIME/IPv6 Addresses

Nodes will generally autoconfigure their IPv6 address based on their IEEE address. The IEEE address can be read directly from the CC2538 Info Page, or it can be hard-coded. Additionally, the user may specify a 2-byte value at build time, which will be used as the IEEE address' 2 LSBs.

To configure the IEEE address source location (Info Page or hard-coded), use the IEEE_ADDR_CONF_HARDCODED define in contiki-conf.h:

  • 0: Info Page
  • 1: Hard-coded

If IEEE_ADDR_CONF_HARDCODED is defined as 1, the IEEE address will take its value from the IEEE_ADDR_CONF_ADDRESS define. If IEEE_ADDR_CONF_HARDCODED is defined as 0, the IEEE address can come from either the primary or secondary location in the Info Page. To use the secondary address, define IEEE_ADDR_CONF_USE_SECONDARY_LOCATION as 1.

Additionally, you can override the IEEE's 2 LSBs, by using the NODEID make variable. The value of NODEID will become the value of the IEEE_ADDR_NODE_ID pre-processor define. If NODEID is not defined, IEEE_ADDR_NODE_ID will not get defined either. For example:

make NODEID=0x79ab

This will result in the 2 last bytes of the IEEE address getting set to 0x79 0xAB

Note: Some early production devices do not have am IEEE address written on the Info Page. For those devices, using value 0 above will result in a Rime address of all 0xFFs. If your device is in this category, define IEEE_ADDR_CONF_HARDCODED to 1 and specify NODEID to differentiate between devices.

Low-Power Modes

The CC2538 port supports power modes for low energy consumption. The SoC will enter a low power mode as part of the main loop when there are no more events to service.

LPM support can be disabled in its entirety by setting LPM_CONF_ENABLE to 0 in contiki-conf.h or project-conf.h.

NOTE: If you are using PG2 version of the Evaluation Module, the SoC will refuse to enter Power Modes 1+ if the debugger is connected and will always enter PM0 regardless of configuration. In order to get real low power mode functionality, make sure the debugger is disconnected. The Battery Board is ideal to test this.

The Low-Power module uses a simple heuristic to determine the best power mode, depending on anticipated Deep Sleep duration and the state of various peripherals.

In a nutshell, the algorithm first answers the following questions:

  • Is the RF off?
  • Are all registered peripherals permitting PM1+?
  • Is the Sleep Timer scheduled to fire an interrupt?

If the answer to any of the above question is "No", the SoC will enter PM0. If the answer to all questions is "Yes", the SoC will enter one of PMs 0/1/2 depending on the expected Deep Sleep duration and subject to user configuration and application requirements.

At runtime, the application may enable/disable some Power Modes by making calls to lpm_set_max_pm(). For example, to avoid PM2 an application could call lpm_set_max_pm(1). Subsequently, to re-enable PM2 the application would call lpm_set_max_pm(2).

The LPM module can be configured with a hard maximum permitted power mode.

#define LPM_CONF_MAX_PM        N

Where N corresponds to the PM number. Supported values are 0, 1, 2. PM3 is not supported. Thus, if the value of the define is 1, the SoC will only ever enter PMs 0 or 1 but never 2 and so on.

The configuration directive LPM_CONF_MAX_PM sets a hard upper boundary. For instance, if LPM_CONF_MAX_PM is defined as 1, calls to lpm_set_max_pm() can only enable/disable PM1. In this scenario, PM2 can not be enabled at runtime.

When setting LPM_CONF_MAX_PM to 0 or 1, the entire SRAM will be available. Crucially, when value 2 is used the linker will automatically stop using the SoC's SRAM non-retention area, resulting in a total available RAM of 16MB instead of 32MB.

LPM and Duty Cycling Driver

LPM is highly related to the operations of the Radio Duty Cycling (RDC) driver of the Contiki network stack and will work correctly with ContikiMAC and NullRDC.

  • With ContikiMAC, PMs 0/1/2 are supported subject to user configuration.
  • When NullRDC is in use, the radio will be always on. As a result, the algorithm discussed above will always choose PM0 and will never attempt to drop to PM1/2.

Shutdown Mode

The Re-Mote allows to further reduce power consumption by shutting down entirely all the components but the Co-Processor, powering completely of the CC2538 and CC1120 even preventing quiescent current from being drawn, allowing the platform to awake after a given period governed by the Co-Processor and the built-in battery management IC. This effectively reduces the power consumption down to 3-4uA.

Build headless nodes

It is possible to turn off all character I/O for nodes not connected to a PC. Doing this will entirely disable the UART as well as the USB controller, preserving energy in the long term. The define used to achieve this is (1: Quiet, 0: Normal output):

#define CC2538_CONF_QUIET      0

Setting this define to 1 will automatically set the following to 0:

  • USB_SERIAL_CONF_ENABLE
  • UART_CONF_ENABLE
  • STARTUP_CONF_VERBOSE

Code Size Optimisations

The build system currently uses optimization level -Os, which is controlled indirectly through the value of the SMALL make variable. This value can be overridden by example makefiles, or it can be changed directly in platform/remote/Makefile.remote.

Historically, the -Os flag has caused problems with some toolchains. If you are using one of the toolchains documented in this README, you should be able to use it without issues. If for whatever reason you do come across problems, try setting SMALL=0 or replacing -Os with -O2 in cpu/cc2538/Makefile.cc2538.

Doxygen Documentation

This port's code has been documented with doxygen. To build the documentation, navigate to $(CONTIKI)/doc and run make. This will build the entire contiki documentation and may take a while.

If you want to build this platform's documentation only and skip the remaining platforms, run this:

make basedirs="platform/remote core cpu/cc2538 examples/remote examples/cc2538dk"

Once you've built the docs, open $(CONTIKI)/doc/html/index.html and enjoy.

Other Versions of this Guide

If you prefer this guide in other formats, use the excellent pandoc to convert it.

  • pdf: pandoc -s --toc README.md -o README.pdf
  • html: pandoc -s --toc README.md -o README.html

More Reading

  1. Zolertia Re-Mote website
  2. CC2538 System-on-Chip Solution for 2.4-GHz IEEE 802.15.4 and ZigBee®/ZigBee IP® Applications, (SWRU319B)
  3. CC1120 sub-1GHz RF transceiver