Contiki OS for 6502 based computers
Go to file
Mariano Alvira a3412a0b81 set the UART1 pin directions in uart1_init()
patch from Hedde Bosman
2011-04-06 05:53:18 -04:00
board add GPIO definitions for econotag LEDs 2011-03-22 14:50:22 -04:00
doc add autoacking 2011-02-12 15:29:11 -05:00
lib add watchdog timer example 2011-03-22 14:51:08 -04:00
src set the UART1 pin directions in uart1_init() 2011-04-06 05:53:18 -04:00
tests add watchdog timer example 2011-03-22 14:51:08 -04:00
tools change short switch for baud to -u 2011-03-15 14:54:11 -04:00
.gitignore ignore generated files 2010-08-20 12:01:44 -04:00
COPYING strip cvs style keywords from everything 2011-02-12 18:12:45 -05:00
CREDITS now BSD license. 2010-05-08 12:55:32 -04:00
Makefile.include add -nodefaultlibs 2010-11-23 15:00:45 -05:00
mc1322x.lds add a memory section for RAM so that the linker will warn when you've 2010-10-16 13:28:20 -04:00
README small clarifications to the README. 2010-02-28 09:17:58 -05:00
TODO more note about autoack --- requires proper hardware addressing 2011-01-16 12:38:34 -05:00

libmc1322x is a library, build system, test code, and utilities for
using the mc13224v from Freescale.

Getting Started
---------------
$ cd tests
$ make

this will build all the test files in libmc1322x/tests for each board
defined in libmc1322x/board. You will have programs like:

  rftest-tx_redbee-dev.bin
  rftest-tx_redbee-r1.bin

  rftest-rx_redbee-dev.bin
  rftest-rx_redbee-r1.bin

if you only wanted to build binaries for one board you can do:

$ make BOARD=redbee-dev

You can use mc1322x-load.pl in libmc1322x/tools to run your code:

$ ../tools/mc1322x-load.pl -f rftest-tx_redbee-dev.bin


Incorporating libmc1322x into your own code
-------------------------------------------

The best way to incorporate libmc1322x into your code is as a git
submodule:

$ mkdir newproject
$ cd newproject
$ git init

   Initialized empty Git repository in /home/malvira/newproject/.git/

$ git submodule add git://git.devl.org/git/malvira/libmc1322x.git

This will add libmc1322x to your repository. Now to setup the
Makefile:

$ cp libmc1322x/tests/Makefile .

You need to edit the Makefile to point MC1322X to your libmc1322x
submodule:

Change line 1

   MC1322X := ..

to 

   MC1322X := libmc1322x

and edit COBJS and TARGETS accordings. COBJS are all of your common
code for any of your programs. TARGETS are the names of your programs.

For instance, you can have a common routine that prints a welcome
message that is used by two programs a and b. You would add common.o
to COBJS:

   COBJS:= common.o

and your target line would read:

   TARGETS := a b 

COBJS are made for each board --- so it is ok to have board specific
code in there. As an example, tests uses this in tests.c to print the
name of the board in the welcome message. You could also use this to
change your GPIO mappings between boards.