Epple-II/doc/cards.asciidoc

267 lines
9.6 KiB
Plaintext
Raw Normal View History

2015-07-17 00:54:10 +00:00
anchor:cards[]
=== Peripheral Cards
==== Disk ][ Controller
The Disk ][ Controller card emulates the floppy disk controller card and associated
disk drives in the original Apple ][ systems. In the emulator, each card has two
drives attached to it, referred to as drive 1 and drive 2. The floppy disks
themselves are represented by a ``nibble'' image of the contents. The
emulator emulates the hardware, but to be of any use, you will need to provide
the firmware ROM code.
To use a disk card and drives, add these lines to your epple2.conf file, for example:
--------
slot 6 disk
import slot 6 rom 0 /usr/lib/apple2/dos3x/16sector/controller/disk2.ex65
--------
2015-07-17 00:54:10 +00:00
The first line uses the <<slot>> command to
insert a disk contoller card into slot 6, which is the standard
slot used for disk cards.
The +disk+ keyword loads the 16-sector P6 ROM (Logic State Sequencer).
Alternatively, use +disk13+ to load the 13-sector P6 ROM (for DOS 3.2 or earlier).
The next line uses the <<import>>
command to load the card's ROM with the disk controller
firmware. This firmware is known as the ``bootstrap'' or ``P5'' ROM code.
It is seen by the Apple ][ at memory addresses $Cs00-$CsFF, where s is the
slot number (so in the common case of the card being in slot 6, the ROM is
at $C600-$C6FF). The firmware is copyright by Apple, and is available from
the http://mosher.mine.nu/apple2/[Apple II Library].
You can also load a floppy disk image (nibble format) into the drive, either by putting
2015-07-17 00:54:10 +00:00
the <<load>> command into the +epple2.conf+ file, or by using the command prompt
in the emulator (+F5+ key). For example, you could load the DOS 3.3 system master into
slot 6, drive 1, with this command
--------
load slot 6 drive 1 /usr/lib/apple2/dos3x/16sector/disks/dos330/clean330sysmas.nib
--------
==== Language
The language card emulates an Apple 16K RAM card, commonly called a Language Card.
To use a language card, add this line to your epple2.conf file:
--------
slot 0 language
--------
Note that DOS and ProDOS will make use of a language card only if it is in slot _zero_.
The language card has RAM at addresses $E000 through $FFFF, as well as two banks of RAM
at addresses $D000 through $DFFF. A program switches between these RAMs and/or the
motherboard ROM by using the I/O switches at $C080 through $C08F.
The information area of the Epple ][ will show the current state of the
language card as follows:
* +R+ Read from card RAM (vs. motherboard ROM)
* +W+ Write to card RAM (vs. write-disabled)
* +B1+ Use $D000 bank 1
* +B2+ Use $D000 bank 2
An overview of the I/O switches that control the language card
is provided by Jim Sather in
http://www.scribd.com/doc/201423/Understanding-the-Apple-II-by-Jim-Sather-1983Quality-Software[Understanding the Apple II],
p. 5-30, Table 5.4, as follows:
[options="header", style="monospaced"]
|==================================================================
| BANK2 | BANK1 2+| ACTION
| C080 | C088 .2+| WRTCOUNT = 0*, WRITE DISABLE .2+| READ ENABLE
| C084 | C08C
| RC081 | RC089 .2+| WRTCOUNT = WRTCOUNT + 1* .2+| READ DISABLE
| RC085 | RC08D
| WC081 | WC089 .2+| WRTCOUNT = 0* .2+| READ DISABLE
| WC085 | WC08D
| C082 | C08A .2+| WRTCOUNT = 0*, WRITE DISABLE .2+| READ DISABLE
| C086 | C08E
| RC083 | RC08B .2+| WRTCOUNT = WRTCOUNT + 1* .2+| READ ENABLE
| RC087 | RC08F
| WC083 | WC08B .2+| WRTCOUNT = 0* .2+| READ ENABLE
| WC087 | WC08F
|==================================================================
^*^ Writing to expansion RAM is enabled when WRTCOUNT reaches 2.
==== Firmware
The firmware card emulates a (modified) Apple Firmware card.
The firmware card is simply an alternate ROM, at addresses
$D000 through $FFFF, that is switched using the I/O switches
at addresses $C080 through $C08F. In order to make use of the
firmware card, you will need to load the ROM with a binary image
from a file on disk. For example, to insert an Integer BASIC
firmware card into the emulator, add these lines to your
+epple2.conf+ file:
--------
# Firmware card with Integer BASIC and old Monitor
slot 0 firmware
import slot 0 rombank 1000 /usr/lib/apple2/system/intbasic/intbasic.ex65
import slot 0 rombank 2425 /usr/lib/apple2/system/other/other.ex65
import slot 0 rombank 2800 /usr/lib/apple2/system/monitor/apple2/monitor.ex65
--------
For an Applesoft BASIC firmware card, use these:
--------
# Firmware card with Applesoft BASIC and Autostart Monitor
slot 0 firmware
import slot 0 rombank 0000 /usr/lib/apple2/system/applesoft/applesoft.ex65
import slot 0 rombank 2800 /usr/lib/apple2/system/monitor/apple2plus/monitor.ex65
--------
Note that the addresses specified in the +epple2.conf+ file for the
rombank are based on the beginning of the bank ROM itself. For example, specifying
+1000+ (which is 1000 hex) represents the final memory address of $E000, because
the bank ROM is always based at address $D000.
The idea is that you would load your motherboard with, for
example, Applesoft BASIC and the Autostart Monitor ROM (to emulate
an Apple ][ plus), and then install a firmware card with Integer
BASIC and the old Monitor. Booting with DOS 3.3, then, would allow
you to type +FP+ to use Applesoft BASIC, or +INT+ to switch to Integer BASIC.
Note that DOS and ProDOS will make use of a firmware card only if it is in slot _zero_.
Jim Sather, in
http://www.scribd.com/doc/201423/Understanding-the-Apple-II-by-Jim-Sather-1983Quality-Software[Understanding the Apple II],
on pages 6-18 through 6-21, explains
how to modify a firmware card to allow independent switching of the $F800-$FFFF
ROM memory. This area is occupied by the Monitor, so it is primarily
intended to allow the user to switch between the old Monitor and the Autostart
Monitor, independent of switching between Integer and Applesoft BASIC. The EPPLE ][
firmware card emulates this behavior.
The information area of the EPPLE ][ will show the current state of the
firmware card as follows:
* +D+ Read from firmware card $D000-$F7FF (vs. motherboard BASIC ROM)
* +F8+ Read from firmware card $F800-$FFFF (vs. motherboard Monitor ROM)
==== Clock
The clock card emulates a ProDOS-compatible real-time clock card for the Apple ][.
To use a clock card, you will need to configure the EPPLE ][ to insert one into
a slot, typically slot 4. You will also need to load the card with its ROM code,
which is provided with the emulator in the clock.ex65 file.
For example, add this to your epple2.conf file:
--------
slot 4 clock
import slot 4 rom 0 /usr/lib/epple2/cards/clock.ex65
--------
Of course you may need to adjust the path for your particular system.
To verify that the clock card is working correctly, you can run the following Applesoft
program to retrieve the current time from the clock card and print it.
This program assumes the card is in slot 4.
[source,vbs]
-------------------------------------------------
NEW
10 CALL -15360 : REM $C400 SLOT 4 ENTRY POINT
20 A = 512 : REM $0200 INPUT BUFFER
30 C = PEEK(A)
40 IF C < 160 THEN 99
50 PRINT CHR$(C);
60 A = A+1
70 GOTO 30
99 END
RUN
-------------------------------------------------
The card returns data (into the GETLN input buffer at $200) in
the following format:
+mm,ww,dd,hh,nn,ss,000,yyyy,Time Zone,v+
* +mm+ Month, 01-12
* +ww+ Weekday, 00=Sunday... 06=Saturday
* +dd+ Day, 01-31
* +hh+ Hour, 00-23
* +nn+ Minute, 00-59
* +ss+ Second, 00-61
* +000+ Milliseconds; always zero
* +yyyy+ Year, e.g., 2008
* +Time Zone+ time zone string (could contain lower-case characters,
which won't display correctly)
* +v+ Daylight Saving Time in effect, 0=no, 1=yes
Note that only +mm,ww,dd,hh,nn+ fields are used by ProDOS. The other
fields, +ss,000,yyyy,Time Zone,v+, are an EPPLE ][ extension. Also note
that ProDOS was not designed to work for years past 2007, so
ProDOS will show the incorrect year, but the other fields will be accurate.
I believe patches exist for ProDOS to fix this.
==== Standard Input
The ``standard input'' card doesn't emulate a real piece of hardware; rather, it
reads characters from standard input (stdin) (of the EPPLE ][ emulator).
To use a standard input card, add these lines to your +epple2.conf+ file:
-------------------------------------------------
# IN#2 reads from standard input
slot 2 stdin
import slot 2 rom 0 /usr/lib/epple2/cards/stdin.ex65
-------------------------------------------------
That will insert a stdin card into slot 2, and then load its
ROM image into the card.
The stdin ROM is provided with the EPPLE ][ distribution.
For example, if you have a stdin card installed in slot 2, start
the EPPLE ][ emulator from the command line, and at the Applesoft
prompt, type +IN#2+. Then you can switch back to the
command shell, and whatever you type will be fed into the emulated
Apple. Use RESET or +IN#0+ to go back to normal.
==== Standard Output
The ``standard output'' card doesn't emulate a real piece of hardware; rather, it acts
similar to a printer card, but instead of sending characters to a printer, it sends
them to standard output (stdout) (of the EPPLE ][ emulator).
To use a standard output card, add these lines to your +epple2.conf+ file:
-------------------------------------------------
# PR#1 prints to standard output
slot 1 stdout
import slot 1 rom 0 /usr/lib/epple2/cards/stdout.ex65
-------------------------------------------------
This will insert a stdout card into slot 1 (which is the typical
slot for a printer card), and then load its ROM image into the card.
The stdout ROM is provided with the EPPLE ][ distribution.
For example, if you have a stdout card installed, at the Applesoft
prompt, type +PR#1+. Whatever you type next will be
echoed to standard output. Type +PR#0+ to stop echoing.