#
# Example SLIP connection script for slipdial v1.0 for GNO/ME and GSTCP.
#
# This script is intended for installations where the IIgs is on a direct
# serial connection to the SLIP server.
#
# This script should be called 'slipscript' and placed in /usr/sbin.  It
# will be launched by tcpip when an attempt to reference a non-local address
# is made, eg: ping, telnet, ftp.  This script is designed to handle static
# slip pretty much as-is, but if you have dynamic slip there are examples
# included which should be sufficient to get you going.  The relevant sections
# are commented out with bangs (!).
#
# All the important strings are assigned at the top of the script for easy
# access and modification.
#
#    $Id: slpscrpt.direct,v 1.1 1999/02/13 06:48:57 gdr-ftp Exp $
#

#
#    String definitons.
#

#    These are the user names and passwords we use to get access to
#    our SLIP server.

$username   = "myGSlogin"
$password   = "myPasswd"

#    $localip is what the IIgs will use.  $remoteip will be used by your
#    SLIP host.

$localip  = "192.168.51.2"
$remoteip = "192.168.51.1"
$netmask  = "255.255.255.255"

#    These are the prompts that we will watch for to see when we should
#    send our user name and password.  The first letter of "login:" and
#    "password:" have been left off here because some system use lower
#    case and some use uppercase.

$userwait = "ogin:"
$passwait = "assword:"

#
# Information on debugging this script:
#
# There are probably enough messages put out by this script that you can
# determine what is going wrong without adding more debug output. However,
# if you wish to add more messages, there are two mechanisms by which 
# you can do so.  The first is to print stuff to stderr:
#	stderr("This is my debug message.")
#
# The second method is to use the syslogd facility.  You can do this by
# inserting lines like this:
#	system("$loggerdebug This is my debug message.")
# Don't try to test the return code from system().
#
# Note the lack of a trailing semicolon in both cases.  This can easily
# bite C and Perl programmers.
#
# Also note that debug output will only show up on console if /usr/sbin/tcpip
# was started from the console rather than from /etc/inittab.
#
# The current mechanism of using syslogd is a bit of a hack; you don't
# want to leave your debugging information in after you get the script
# running because that can significantly lengthen the time it takes to
# connect to your server.
#
# Debug messages should always call $loggerdebug rather than $loggerinfo.
# The latter is used for messages that should never be deleted from this
# script; they are useful for when things go awry.
#
$loggerdebug = "/usr/bin/logger -t slipscript -p daemon.debug"
$loggerinfo  = "/usr/bin/logger -t slipscript -p daemon.info"

#
#    Program start.
#

#    First, open up our port

ifequ ($1,"slipb")                 # $1 is the second commandline argument,
   $portname = ".ttya"             # which should be either slipa or slipb.
eifequ ($1,"slipa")
   $portname = ".ttyb"
else
   goto(noarg)
$port = open($portname)
ifequ ($port)                      # If we got an error opening the port, abort
   goto(abort)

# Here is an example debug message.
# $message = "opened port $portname"
# stderr("$message")
# system("$loggerdebug $message")

#
#    Connect to remote host.
#
#    Now, we have a series of sends/waits to get to the slip server.
#    This is dependant on what the system you are trying to connect to is
#    like and MUST be edited!  The below is just an EXAMPLE.
#
#    We send a few carriage returns so that we can hopefully get our
#    login prompt.  If we still don't see the prompt, throw an error.
#
send($port,"\r")
send($port,"\r")   
send($port,"\r")   
$offline = wait($port,$userwait,5)
ifnot ($offline)
        goto(hangup)

#    provide our SLIP login name                    
send($port,$username)

#    wait for the "Password:" string and send our password
$gotpass = wait($port,$passwait,5)
ifnot ($gotpass)
	goto(hangup)
send($port,$password)

#    Here we assume that the account we're using immediately starts the
#    SLIP protcol once the login has succeeded.  If this is not the case,
#    then you should add in a few more wait/send pairs (as appropriate)
#    to start SLIP on your server.

#    For Dyanamic IP Only - we can now pick off the IP address that is our
#    address.  If you also need to get your router's IP address, you can do
#    a getip() for that too.
                    
!$gotip = getip($localip,$port,"Your IP address is "," Server address")
!ifnot ($gotip)
!   goto(hangup)         # We didn't get an IP back, so abort.

#    Now wait for the banner that says our server is entering SLIP mode.
$gotslip = wait($port,"Starting SLIP",5)
ifnot ($gotslip)
	goto(hangup)
                    
$success = system("/sbin/ifconfig $1 $localip $remoteip netmask $netmask")
#    Here we would normally check the result of system() to see if the
#    ifconfig call was successful.  However, there is a bug right now in
#    that system() will always return a failure code, so we skip this test.
# $ifnot ($success)         
#   goto(hangup)         # An error occured system()ing ifconfig or ifconfig
                         # was unable to execute properly, so abort.

#                   
#    Done.  We are now online, so close up and exit success
#

:done
   close($port)
   system("$loggerinfo connect $1 local $localip remote $remoteip netmask $netmask")
   exit(0)

#
#    Unsuccessful completion handlers follow
#

#    Hangup - we made a connection, but didn't get slip started for some reason

:hangup
   $message = "Unable to start SLIPping to remote host -- Giving up"
   stderr("$message")
   system("$loggerinfo $message")
   close($port)
   exit(1)

#    No connection made.

:noconnect
   $message = "Unable to make connection to remote host -- Giving up"
   stderr("$message")
   system("$loggerinfo $message")
   close($port)
   exit(1)

#    No argument given on the commandline for slipa or slipb.

:noarg
   $message = "Unable to find sliptype parameter -- Giving up"
   stderr("$message")
   system("$loggerinfo $message")
   exit(1)

#    Abort!  We can't even open a port, so just quit

:abort
   $message = "Error opening port $1 -- Giving up"
   stderr("$message")
   system("$loggerinfo $message")
   exit(1)