1054 lines
39 KiB
ArmAsm
1054 lines
39 KiB
ArmAsm
; Subroutines that deal with the horizontal scrolling. The primary function of
|
|
; these routines are to adjust tables and patch in new values into the code field
|
|
; when the virtual X-position of the play field changes.
|
|
|
|
; NOTE: There is still quite a bit of work done in the blitter to figure out if an
|
|
; opcode is a PEA, LDA or JMP. If there _some_ way that we could engineer a single
|
|
; target opcode change that would allow us to take different code branches in the
|
|
; blitter based on the opcode since the save/restore code has a change to look
|
|
; at the opcode now; before the blitter executes.
|
|
;
|
|
; PEA = $F4 = %1111 0100
|
|
; LDA (),y = $B1 = %1011 0001
|
|
; LDA 0,x = $B5 = %1011 0101
|
|
; JMP addr = $4C = %0100 1100
|
|
;
|
|
; IDEA: Save the 2-byte code directly after a BRA opcode to unconditionally branch out after masking. Would be a
|
|
; bit tricky to handle the forward and backward branches.
|
|
;
|
|
; Improvement. The current "fast path" for the PEA operand is
|
|
;
|
|
; ldal l_is_jmp+1-base ; 6
|
|
; bit #$000B ; 3
|
|
; bne :chk_jmp ; 2
|
|
; sep #$20 ; 3
|
|
; ldal l_is_jmp+3-base ; 5
|
|
; pha ; 3 = 22 cycles
|
|
;
|
|
; If we do an immediate branch to a routine that we _know_ is the right one, the code reduces to
|
|
;
|
|
; bra pea ; 3
|
|
; sep #$20 ; 3
|
|
; ldal l_is_jmp+3-base ; 5
|
|
; pha ; 3 = 17 cycles
|
|
;
|
|
; Even if some additional branch is needed, it is likely to be a small improvement for the PEA case
|
|
; and a significant improvement for the other cases since it avoids the chain of BIT instructions
|
|
|
|
; Simple function that restores the saved opcode that are stashed in _applyBG0Xpos. It is
|
|
; very important that opcodes are restored before new ones are inserted, because there is
|
|
; only one, fixed storage location and old values will be overwritten if operations are not
|
|
; performed in order.
|
|
;
|
|
; Experimental -- this is a parameterized version that does not rely on direct page
|
|
; state variables for input and attempts to be more optimized.
|
|
;
|
|
; A = starting virtual line in the code field (0 - 207)
|
|
; X = number of lines to render (0 - 200)
|
|
|
|
_RestoreBG0Opcodes
|
|
|
|
:virt_line_x2 equ tmp1
|
|
:lines_left_x2 equ tmp2
|
|
:exit_offset equ tmp4
|
|
|
|
asl
|
|
sta :virt_line_x2 ; Keep track of it
|
|
|
|
txa
|
|
asl
|
|
sta :lines_left_x2
|
|
|
|
lda LastPatchOffset ; If zero, there are no saved opcodes
|
|
sta :exit_offset
|
|
|
|
_RestoreBG0OpcodesAlt
|
|
:virt_line_x2 equ tmp1
|
|
:lines_left_x2 equ tmp2
|
|
:draw_count_x2 equ tmp3
|
|
:exit_offset equ tmp4
|
|
:stk_save equ tmp5
|
|
|
|
phb ; Save data bank
|
|
tsc
|
|
sta :stk_save
|
|
|
|
:loop
|
|
ldx :virt_line_x2
|
|
ldal BTableLow,x ; Get the address of the first code field line
|
|
tay
|
|
|
|
ldal BTableHigh,x ; This intentionally leaks one byte on the stack
|
|
pha
|
|
plb ; This is the bank that will receive the updates
|
|
|
|
txa ; lda :virt_line_x2
|
|
and #$001E
|
|
eor #$FFFF
|
|
sec
|
|
adc #32
|
|
min :lines_left_x2
|
|
sta :draw_count_x2 ; Do half of this many lines
|
|
|
|
; y is already set to :base_address
|
|
tax ; :draw_count * 2
|
|
clc
|
|
adc :virt_line_x2
|
|
sta :virt_line_x2
|
|
|
|
tya
|
|
adc :exit_offset ; Add some offsets to get the base address in the code field line
|
|
|
|
RestoreOpcode
|
|
|
|
lda :lines_left_x2 ; subtract the number of lines we just completed
|
|
sec
|
|
sbc :draw_count_x2
|
|
sta :lines_left_x2
|
|
|
|
jne :loop
|
|
|
|
stz LastPatchOffset ; Clear the value once completed
|
|
|
|
lda :stk_save
|
|
tcs
|
|
plb
|
|
rts
|
|
|
|
; Based on the current value of StartX in the direct page, patch up the code fields
|
|
; to render the correct data. Note that we do *not* do the OpcodeRestore in this
|
|
; routine. The reason is that the restore *must* be applied using the (StartX, StartY)
|
|
; values from the previous frame, which requires logic that is not relevant to setting
|
|
; up the code field.
|
|
;
|
|
; This function is where the reverse-mapping aspect of the code field is compensated
|
|
; for. In the initialize case where X = 0, the exit point is at the *end* of
|
|
; the code buffer line
|
|
;
|
|
; +----+----+ ... +----+----+----+
|
|
; | 82 | 80 | | 04 | 02 | 00 |
|
|
; +----+----+ ... +----+----+----+
|
|
; ^ x=0
|
|
;
|
|
; As the screen scrolls right-to-left, the exit position moves to earlier memory
|
|
; locations until wrapping around from 163 to 0.
|
|
;
|
|
; The net calculation are
|
|
;
|
|
; x_exit = (164 - x) % 164
|
|
; x_enter = (164 - x - width) % 164
|
|
;
|
|
|
|
; Small routine to put the data in a consistent state. Called before any routines need to draw on
|
|
; the code buffer, but before we patch out the instructions.
|
|
_ApplyBG0XPosPre
|
|
lda StartX ; This is the starting byte offset (0 - 163)
|
|
jsr Mod164
|
|
sta StartXMod164
|
|
rts
|
|
|
|
_ApplyBG0XPos
|
|
:virt_line_x2 equ tmp1
|
|
:lines_left_x2 equ tmp2
|
|
|
|
; If there are saved opcodes that have not been restored, do not run this routine
|
|
lda LastPatchOffset
|
|
beq :ok
|
|
rts
|
|
|
|
; This code is fairly succinct. See the corresponding code in Vert.s for more detailed comments.
|
|
:ok
|
|
lda StartYMod208 ; This is the base line of the virtual screen
|
|
asl
|
|
sta :virt_line_x2 ; Keep track of it
|
|
|
|
lda ScreenHeight
|
|
asl
|
|
sta :lines_left_x2
|
|
|
|
; Calculate the exit and entry offsets into the code fields. This is a bit tricky, because odd-aligned
|
|
; rendering causes the left and right edges to move in a staggered fashion.
|
|
;
|
|
; ... +----+----+----+----+----+- ... -+----+----+----+----+----+
|
|
; | 04 | 06 | 08 | 0A | 0C | | 44 | 46 | 48 | 4A |
|
|
; ... +----+----+----+----+----+- ... -+----+----+----+----+----+
|
|
; | |
|
|
; +---- screen width --------------+
|
|
; entry | | exit
|
|
;
|
|
; Here is an example of a screen 64 bytes wide. When everything is aligned to an even offset
|
|
; then the entry point is column $08 and the exit point is column $48
|
|
;
|
|
; If we move the screen forward one byte (which means the pointers move backwards) then the low-byte
|
|
; of column $06 will be on the right edge of the screen and the high-byte of column $46 will left-edge
|
|
; of the screen. Since the one-byte edges are handled specially, the exit point shifts one column, but
|
|
; the entry point does not.
|
|
;
|
|
; ... +----+----+----+----+----+- ... -+----+----+----+----+----+
|
|
; | 04 | 06 | 08 | 0A | 0C | | 44 | 46 | 48 | 4A |
|
|
; ... +----+----+----+----+----+- ... -+----+----+----+----+----+
|
|
; | | | |
|
|
; +--|------ screen width -------|--+
|
|
; entry | | exit
|
|
;
|
|
; When the screen is moved one more byte forward, then the entry point will move to the
|
|
; next column.
|
|
;
|
|
; ... +----+----+----+----+----+- ... -+----+----+----+----+----+
|
|
; | 04 | 06 | 08 | 0A | 0C | | 44 | 46 | 48 | 4A |
|
|
; ... +----+----+----+----+----+- ... -+----+----+----+----+----+
|
|
; | |
|
|
; +------ screen width ------------+
|
|
; entry | | exit
|
|
;
|
|
; So, in short, the entry tile position is rounded up from the x-position and the exit
|
|
; tile position is rounded down.
|
|
;
|
|
; Now, the left edge of the screen is pushed last, so we need to exit one instruction *after*
|
|
; the location (163 - StartX % 164)
|
|
;
|
|
; x = 0
|
|
;
|
|
; | PEA $0000 |
|
|
; +-----------+
|
|
; | PEA $0000 |
|
|
; +-----------+
|
|
; | JMP loop | <-- Exit here
|
|
; +-----------+
|
|
;
|
|
; x = 1 and 2
|
|
;
|
|
; | PEA $0000 |
|
|
; +-----------+
|
|
; | PEA $0000 | <-- Exit Here
|
|
; +-----------+
|
|
; | JMP loop |
|
|
; +-----------+
|
|
|
|
lda StartXMod164
|
|
|
|
; Alternate entry point if the virt_line_x2 and lines_left_x2 and XMod164 values are passed in externally
|
|
_ApplyBG0XPosAlt
|
|
:stk_save equ tmp0
|
|
:virt_line_x2 equ tmp1
|
|
:lines_left_x2 equ tmp2
|
|
:draw_count_x2 equ tmp3
|
|
:exit_offset equ tmp4
|
|
:entry_offset equ tmp5
|
|
:exit_bra equ tmp6
|
|
:exit_address equ tmp7
|
|
:base_address equ tmp8
|
|
:opcode equ tmp9
|
|
:odd_entry_offset equ tmp10
|
|
|
|
bit #$0001
|
|
jne :odd_case ; Specialized routines for even/odd cases
|
|
|
|
; If the exit byte is odd, then the left edge is even-aligned and we round down and exit at at
|
|
; that word.
|
|
;
|
|
; If the exit byte is even, then the left edge is odd-aligned and we exit at this word.
|
|
|
|
tax
|
|
lda CodeFieldEvenBRA-2,x
|
|
sta :exit_bra
|
|
lda Col2CodeOffset-2,x
|
|
sta :exit_offset
|
|
sta LastPatchOffset ; Cache as a flag for later
|
|
|
|
; Calculate the entry point into the code field by calculating the right edge
|
|
|
|
txa ; lda StartXMod164
|
|
clc
|
|
adc ScreenWidth ; move to the right edge
|
|
|
|
cmp #164 ; Keep the value in range
|
|
bcc *+5
|
|
sbc #164
|
|
|
|
; Same logic as above. If the right edge is odd, then the full word needs to be drawn and we
|
|
; will enter at that index, rounded down.
|
|
;
|
|
; If the right edge is even, then only the low byte needs to be drawn, which is handled before
|
|
; entering the code field. So enter one word before the right edge.
|
|
;
|
|
; We performan an optimization here and fuse the entry_offset byte with the opcode that is
|
|
; changed depending on even/odd alignment in order to do the work with a single 16-bit
|
|
; store instead of two 8-bit stores.
|
|
|
|
tax
|
|
lda Col2CodeOffset-3,x ; Only use the one byte for the entry_offset
|
|
and #$FF00
|
|
ora #$004C ; Merge in the JMP instruction
|
|
sta :opcode
|
|
|
|
; Main loop that
|
|
;
|
|
; 1. Saves the opcodes in the code field
|
|
; 2. Writes the BRA instruction to exit the code field
|
|
; 3. Writes the JMP entry point to enter the code field
|
|
|
|
phb ; Save the existing bank
|
|
tsc
|
|
sta :stk_save
|
|
|
|
:even_loop
|
|
ldx :virt_line_x2
|
|
|
|
ldal BTableHigh,x ; Get the bank
|
|
pha
|
|
plb
|
|
|
|
ldal BTableLow,x ; Get the address of the first code field line
|
|
tay ; Save it to use as the base address
|
|
|
|
txa ; Calculate number of lines to draw on this iteration
|
|
and #$001E
|
|
eor #$FFFF
|
|
sec
|
|
adc #32
|
|
min :lines_left_x2
|
|
sta :draw_count_x2
|
|
tax ; Use for the first iteration
|
|
|
|
tya
|
|
clc
|
|
adc :exit_offset ; Add some offsets to get the base address in the code field line
|
|
sta :exit_address
|
|
sty :base_address
|
|
|
|
; First step is to set the BRA instruction to exit the code field at the proper location. There
|
|
; are two sub-steps to do here; we need to save the 16-bit value that exists at the location and
|
|
; then overwrite it with the branch instruction.
|
|
;
|
|
; Special note, the SaveOpcode function stores the opcode *within* the code field as it is
|
|
; used in odd-aligned cases to determine how to draw the 8-bit value on the left edge of the
|
|
; screen
|
|
; y is already set to :base_address
|
|
; ldx :draw_count_x2 ; :draw_count_x2
|
|
; lda :exit_address ; Save from this location (not needed in fast mode)
|
|
SaveOpcode ; X = :exit_address on return
|
|
|
|
txy ; ldy :exit_address -- starting at this address
|
|
ldx :draw_count_x2 ; Do this many lines
|
|
lda :exit_bra ; Copy this value into all of the lines
|
|
SetConst ; All registers are preserved
|
|
|
|
; Now, patch in the opcode + code entry_offset
|
|
|
|
ldy :base_address
|
|
lda :opcode
|
|
SetCodeEntryOpcode ; All registers are preserved
|
|
|
|
; Do the end of the loop -- update the virtual line counter and reduce the number
|
|
; of lines left to render
|
|
|
|
clc
|
|
lda :virt_line_x2 ; advance to the virtual line after
|
|
adc :draw_count_x2 ; filled in
|
|
sta :virt_line_x2
|
|
|
|
lda :lines_left_x2 ; subtract the number of lines we just completed
|
|
sec
|
|
sbc :draw_count_x2
|
|
sta :lines_left_x2
|
|
|
|
jne :even_loop
|
|
|
|
lda :stk_save
|
|
tcs
|
|
plb
|
|
rts
|
|
|
|
:odd_case
|
|
dec
|
|
tax
|
|
lda CodeFieldOddBRA,x
|
|
sta :exit_bra
|
|
lda Col2CodeOffset,x
|
|
sta :exit_offset
|
|
sta LastPatchOffset ; Cache as a flag for later
|
|
|
|
txa ; StartXMod164 - 1
|
|
clc
|
|
adc ScreenWidth
|
|
cmp #164 ; Keep the value in range
|
|
bcc *+5
|
|
sbc #164
|
|
|
|
tax
|
|
lda Col2CodeOffset-1,x ; Odd offset to get the value in the high byte
|
|
and #$FF00
|
|
ora #$00AF
|
|
sta :opcode
|
|
|
|
lda Col2CodeOffset-2,x
|
|
sta :odd_entry_offset
|
|
|
|
; Main loop
|
|
|
|
phb ; Save the existing bank
|
|
tsc
|
|
sta :stk_save
|
|
|
|
:odd_loop
|
|
ldx :virt_line_x2
|
|
|
|
ldal BTableHigh,x ; Get the bank
|
|
pha
|
|
plb
|
|
|
|
ldal BTableLow,x ; Get the address of the first code field line
|
|
tay ; Save it to use as the base address
|
|
|
|
txa ; Calculate number of lines to draw on this iteration
|
|
and #$001E
|
|
eor #$FFFF
|
|
sec
|
|
adc #32
|
|
min :lines_left_x2
|
|
sta :draw_count_x2
|
|
tax ; Use for the first iteration
|
|
|
|
tya
|
|
clc
|
|
adc :exit_offset ; Add some offsets to get the base address in the code field line
|
|
sta :exit_address
|
|
sty :base_address
|
|
|
|
; At this point y = :base_address, x = :draw_count_x2 and the accumulator is the exit_address
|
|
|
|
SaveOpcodeAndOperand ; X = :exit_address on return
|
|
|
|
txy ; ldy :exit_address -- starting at this address
|
|
ldx :draw_count_x2 ; Do this many lines
|
|
lda :exit_bra ; Copy this value into all of the lines
|
|
SetConst ; All registers are preserved
|
|
|
|
; Now, patch in the opcode + code entry_offset
|
|
|
|
ldy :base_address
|
|
lda :opcode
|
|
SetCodeEntryOpcode ; All registers are preserved
|
|
|
|
; The odd case need to do a bit of extra work
|
|
|
|
sep #$20
|
|
lda :odd_entry_offset
|
|
SetOddCodeEntry ; All registers are preserved
|
|
rep #$21 ; Clear the carry
|
|
|
|
lda :virt_line_x2 ; advance to the virtual line after
|
|
adc :draw_count_x2 ; filled in
|
|
sta :virt_line_x2
|
|
|
|
lda :lines_left_x2 ; subtract the number of lines we just completed
|
|
sec
|
|
sbc :draw_count_x2
|
|
sta :lines_left_x2
|
|
|
|
jne :odd_loop
|
|
|
|
lda :stk_save
|
|
tcs
|
|
plb
|
|
rts
|
|
|
|
_RestoreScanlineBG0Opcodes
|
|
:virt_line_x2 equ tmp1
|
|
:lines_left_x2 equ tmp2
|
|
:exit_offset equ tmp4
|
|
|
|
; Avoid local var collisions
|
|
:virt_line_pos_x2 equ tmp11
|
|
:total_left_x2 equ tmp12
|
|
:current_count_x2 equ tmp13
|
|
:ptr equ tmp14
|
|
|
|
asl
|
|
sta :virt_line_pos_x2
|
|
tay
|
|
|
|
txa
|
|
asl
|
|
sta :total_left_x2
|
|
|
|
lda StartXMod164Tbl
|
|
sta :ptr
|
|
lda StartXMod164Tbl+2
|
|
sta :ptr+2
|
|
|
|
; Patch our the ranges from the StartXMod164Tbl array starting at the first virtual line
|
|
:loop
|
|
lda [:ptr],y
|
|
and #$FF00 ; Determine how many sequential lines to restore
|
|
xba
|
|
inc
|
|
asl
|
|
min :total_left_x2 ; Don't draw more than the number of lines that are left to process
|
|
sta :current_count_x2 ; Save a copy for later
|
|
|
|
sta :lines_left_x2 ; Set the parameter
|
|
sty :virt_line_x2 ; Set the parameter
|
|
lda LastOffsetTbl,y
|
|
sta :exit_offset
|
|
jsr _RestoreBG0OpcodesAlt
|
|
|
|
clc
|
|
lda :virt_line_pos_x2
|
|
adc :current_count_x2
|
|
cmp #208*2 ; Do the modulo check in this loop
|
|
bcc *+5
|
|
sbc #208*2
|
|
sta :virt_line_pos_x2
|
|
tay
|
|
|
|
lda :total_left_x2
|
|
sec
|
|
sbc :current_count_x2
|
|
sta :total_left_x2
|
|
bne :loop
|
|
|
|
rts
|
|
|
|
; This is a variant of the above routine that allows each x-position to be set independently from a table of value. This is
|
|
; quite a bit slower than the other routine since we cannot store constant values for each line.
|
|
;
|
|
; This routine operates at a higher level and does not try to be super optimized for the case where every line has a different
|
|
; set of parameters. Instead, we optimize for the case where there are a few large ranges of the screen moving at different
|
|
; rates, e.g. a fixed status bar area on top, a slow-scrolling area in the middle and a fast are in the foreground.
|
|
;
|
|
; The table that drives this is dense and has the following format for each word
|
|
;
|
|
; Bits 0 - 7: X mod 164 value
|
|
; Bits 8 - 15: Number of scanline to persist this mod value
|
|
;
|
|
; So, if the first 10 entries has a mod value of 5, they would look like: $0905, $0805, $0705, ... $0105, $0005
|
|
;
|
|
; This allows the code to start an an arbitrary location and immeditely sync up with the modulo list. It also allows
|
|
; the code to easily skip ranges of constant values using the existing _ApplyBG0XPos function as a subroutine.
|
|
_ApplyScanlineBG0XPos
|
|
|
|
; Copies of the local variables in _ApplyBG0XPos
|
|
:virt_line_x2 equ tmp1
|
|
:lines_left_x2 equ tmp2
|
|
:exit_offset equ tmp4
|
|
|
|
; Avoid local var collision with _ApplyBG0XPos
|
|
:virt_line_pos_x2 equ tmp11
|
|
:total_left_x2 equ tmp12
|
|
:current_count_x2 equ tmp13
|
|
:ptr equ tmp14
|
|
|
|
lda StartXMod164Tbl
|
|
sta :ptr
|
|
lda StartXMod164Tbl+2
|
|
sta :ptr+2
|
|
ora :ptr
|
|
bne *+3 ; null pointer check
|
|
rts
|
|
|
|
lda StartYMod208 ; This is the base line of the virtual screen
|
|
asl
|
|
sta :virt_line_pos_x2
|
|
tay
|
|
|
|
lda ScreenHeight
|
|
asl
|
|
sta :total_left_x2
|
|
|
|
; Patch our the ranges from the StartXMod164Tbl array starting at the first virtual line
|
|
:loop
|
|
lda [:ptr],y
|
|
tax
|
|
|
|
and #$FF00 ; Determine how many sequential lines have this mod value
|
|
xba
|
|
inc
|
|
asl
|
|
min :total_left_x2 ; Don't draw more than the number of lines that are left to process
|
|
sta :current_count_x2 ; Save a copy for later
|
|
|
|
sta :lines_left_x2 ; Set the parameter
|
|
sty :virt_line_x2 ; Set the parameter
|
|
txa ; Put the X mod 164 value in the accumulator
|
|
and #$00FF
|
|
jsr _ApplyBG0XPosAlt
|
|
|
|
lda :exit_offset ; Get the direct address in the code field that was overwritten
|
|
ldy :virt_line_pos_x2
|
|
sta LastOffsetTbl,y ; Stash it for use by the per-scanline resotre function
|
|
|
|
tya
|
|
clc
|
|
adc :current_count_x2
|
|
cmp #208*2 ; Do the modulo check in this loop
|
|
bcc *+5
|
|
sbc #208*2
|
|
sta :virt_line_pos_x2
|
|
tay
|
|
|
|
lda :total_left_x2
|
|
sec
|
|
sbc :current_count_x2
|
|
sta :total_left_x2
|
|
bne :loop
|
|
|
|
rts
|
|
|
|
; SaveHighOperand
|
|
;
|
|
; Save the high byte of the 3-byte code field instruction into the odd handler at the end
|
|
; of each line. This is only needed
|
|
;
|
|
; X = number of lines * 2, 0 to 32
|
|
; Y = starting line * $1000
|
|
; A = code field location * $1000
|
|
SaveHighOperand mac
|
|
jmp (dispTbl,x)
|
|
dispTbl da bottom
|
|
da do01,do02,do03,do04
|
|
da do05,do06,do07,do08
|
|
da do09,do10,do11,do12
|
|
da do13,do14,do15,do16
|
|
|
|
do15 ldx ]1 ; accumulator is in 8-bit mode, so can't use TAX
|
|
bra x15
|
|
do14 ldx ]1
|
|
bra x14
|
|
do13 ldx ]1
|
|
bra x13
|
|
do12 ldx ]1
|
|
bra x12
|
|
do11 ldx ]1
|
|
bra x11
|
|
do10 ldx ]1
|
|
bra x10
|
|
do09 ldx ]1
|
|
bra x09
|
|
do08 ldx ]1
|
|
bra x08
|
|
do07 ldx ]1
|
|
bra x07
|
|
do06 ldx ]1
|
|
bra x06
|
|
do05 ldx ]1
|
|
bra x05
|
|
do04 ldx ]1
|
|
bra x04
|
|
do03 ldx ]1
|
|
bra x03
|
|
do02 ldx ]1
|
|
bra x02
|
|
do01 ldx ]1
|
|
bra x01
|
|
do16 ldx ]1
|
|
x16 lda $F001,x
|
|
sta OPCODE_HIGH_SAVE+$F000,y
|
|
x15 lda $E001,x
|
|
sta OPCODE_HIGH_SAVE+$E000,y
|
|
x14 lda $D001,x
|
|
sta OPCODE_HIGH_SAVE+$D000,y
|
|
x13 lda $C001,x
|
|
sta OPCODE_HIGH_SAVE+$C000,y
|
|
x12 lda $B001,x
|
|
sta OPCODE_HIGH_SAVE+$B000,y
|
|
x11 lda $A001,x
|
|
sta OPCODE_HIGH_SAVE+$A000,y
|
|
x10 lda $9001,x
|
|
sta OPCODE_HIGH_SAVE+$9000,y
|
|
x09 lda $8001,x
|
|
sta OPCODE_HIGH_SAVE+$8000,y
|
|
x08 lda $7001,x
|
|
sta OPCODE_HIGH_SAVE+$7000,y
|
|
x07 lda $6001,x
|
|
sta OPCODE_HIGH_SAVE+$6000,y
|
|
x06 lda $5001,x
|
|
sta OPCODE_HIGH_SAVE+$5000,y
|
|
x05 lda $4001,x
|
|
sta OPCODE_HIGH_SAVE+$4000,y
|
|
x04 lda $3001,x
|
|
sta OPCODE_HIGH_SAVE+$3000,y
|
|
x03 lda $2001,x
|
|
sta OPCODE_HIGH_SAVE+$2000,y
|
|
x02 lda $1001,x
|
|
sta OPCODE_HIGH_SAVE+$1000,y
|
|
x01 lda: $0001,x
|
|
sta: OPCODE_HIGH_SAVE+$0000,y
|
|
bottom <<<
|
|
|
|
; SaveOpcode
|
|
;
|
|
; Save the values to the restore location. This should only be used to patch the
|
|
; code field since the save location is fixed.
|
|
;
|
|
; X = number of lines * 2, 0 to 32
|
|
; Y = starting line * $1000
|
|
; A = code field location * $1000
|
|
SaveOpcode mac
|
|
jmp (dispTbl,x)
|
|
dispTbl da bottom
|
|
da do01,do02,do03,do04
|
|
da do05,do06,do07,do08
|
|
da do09,do10,do11,do12
|
|
da do13,do14,do15,do16
|
|
|
|
do15 tax
|
|
bra x15
|
|
do14 tax
|
|
bra x14
|
|
do13 tax
|
|
bra x13
|
|
do12 tax
|
|
bra x12
|
|
do11 tax
|
|
bra x11
|
|
do10 tax
|
|
bra x10
|
|
do09 tax
|
|
bra x09
|
|
do08 tax
|
|
bra x08
|
|
do07 tax
|
|
bra x07
|
|
do06 tax
|
|
bra x06
|
|
do05 tax
|
|
bra x05
|
|
do04 tax
|
|
bra x04
|
|
do03 tax
|
|
bra x03
|
|
do02 tax
|
|
bra x02
|
|
do01 tax
|
|
bra x01
|
|
do16 tax
|
|
x16 lda $F000,x
|
|
sta OPCODE_SAVE+$F000,y
|
|
x15 lda $E000,x
|
|
sta OPCODE_SAVE+$E000,y
|
|
x14 lda $D000,x
|
|
sta OPCODE_SAVE+$D000,y
|
|
x13 lda $C000,x
|
|
sta OPCODE_SAVE+$C000,y
|
|
x12 lda $B000,x
|
|
sta OPCODE_SAVE+$B000,y
|
|
x11 lda $A000,x
|
|
sta OPCODE_SAVE+$A000,y
|
|
x10 lda $9000,x
|
|
sta OPCODE_SAVE+$9000,y
|
|
x09 lda $8000,x
|
|
sta OPCODE_SAVE+$8000,y
|
|
x08 lda $7000,x
|
|
sta OPCODE_SAVE+$7000,y
|
|
x07 lda $6000,x
|
|
sta OPCODE_SAVE+$6000,y
|
|
x06 lda $5000,x
|
|
sta OPCODE_SAVE+$5000,y
|
|
x05 lda $4000,x
|
|
sta OPCODE_SAVE+$4000,y
|
|
x04 lda $3000,x
|
|
sta OPCODE_SAVE+$3000,y
|
|
x03 lda $2000,x
|
|
sta OPCODE_SAVE+$2000,y
|
|
x02 lda $1000,x
|
|
sta OPCODE_SAVE+$1000,y
|
|
x01 lda: $0000,x
|
|
sta: OPCODE_SAVE+$0000,y
|
|
bottom
|
|
<<<
|
|
|
|
; SaveOpcodeAndOperand
|
|
;
|
|
; Save both the opcode and operand at the same time
|
|
;
|
|
; X = number of lines * 2, 0 to 32
|
|
; Y = starting line * $1000
|
|
; A = code field location * $1000
|
|
SaveOpcodeAndOperand mac
|
|
jmp (dispTbl,x)
|
|
dispTbl da bottom
|
|
da do01,do02,do03,do04
|
|
da do05,do06,do07,do08
|
|
da do09,do10,do11,do12
|
|
da do13,do14,do15,do16
|
|
|
|
do15 tax
|
|
jmp x15
|
|
do14 tax
|
|
jmp x14
|
|
do13 tax
|
|
jmp x13
|
|
do12 tax
|
|
jmp x12
|
|
do11 tax
|
|
jmp x11
|
|
do10 tax
|
|
jmp x10
|
|
do09 tax
|
|
jmp x09
|
|
do08 tax
|
|
jmp x08
|
|
do07 tax
|
|
jmp x07
|
|
do06 tax
|
|
jmp x06
|
|
do05 tax
|
|
jmp x05
|
|
do04 tax
|
|
jmp x04
|
|
do03 tax
|
|
jmp x03
|
|
do02 tax
|
|
jmp x02
|
|
do01 tax
|
|
jmp x01
|
|
do16 tax
|
|
x16 lda $F000,x
|
|
sta OPCODE_SAVE+$F000,y
|
|
lda $F001,x
|
|
sta OPCODE_HIGH_SAVE+$F000,y
|
|
x15 lda $E000,x
|
|
sta OPCODE_SAVE+$E000,y
|
|
lda $E001,x
|
|
sta OPCODE_HIGH_SAVE+$E000,y
|
|
x14 lda $D000,x
|
|
sta OPCODE_SAVE+$D000,y
|
|
lda $D001,x
|
|
sta OPCODE_HIGH_SAVE+$D000,y
|
|
x13 lda $C000,x
|
|
sta OPCODE_SAVE+$C000,y
|
|
lda $C001,x
|
|
sta OPCODE_HIGH_SAVE+$C000,y
|
|
x12 lda $B000,x
|
|
sta OPCODE_SAVE+$B000,y
|
|
lda $B001,x
|
|
sta OPCODE_HIGH_SAVE+$B000,y
|
|
x11 lda $A000,x
|
|
sta OPCODE_SAVE+$A000,y
|
|
lda $A001,x
|
|
sta OPCODE_HIGH_SAVE+$A000,y
|
|
x10 lda $9000,x
|
|
sta OPCODE_SAVE+$9000,y
|
|
lda $9001,x
|
|
sta OPCODE_HIGH_SAVE+$9000,y
|
|
x09 lda $8000,x
|
|
sta OPCODE_SAVE+$8000,y
|
|
lda $8001,x
|
|
sta OPCODE_HIGH_SAVE+$8000,y
|
|
x08 lda $7000,x
|
|
sta OPCODE_SAVE+$7000,y
|
|
lda $7001,x
|
|
sta OPCODE_HIGH_SAVE+$7000,y
|
|
x07 lda $6000,x
|
|
sta OPCODE_SAVE+$6000,y
|
|
lda $6001,x
|
|
sta OPCODE_HIGH_SAVE+$6000,y
|
|
x06 lda $5000,x
|
|
sta OPCODE_SAVE+$5000,y
|
|
lda $5001,x
|
|
sta OPCODE_HIGH_SAVE+$5000,y
|
|
x05 lda $4000,x
|
|
sta OPCODE_SAVE+$4000,y
|
|
lda $4001,x
|
|
sta OPCODE_HIGH_SAVE+$4000,y
|
|
x04 lda $3000,x
|
|
sta OPCODE_SAVE+$3000,y
|
|
lda $3001,x
|
|
sta OPCODE_HIGH_SAVE+$3000,y
|
|
x03 lda $2000,x
|
|
sta OPCODE_SAVE+$2000,y
|
|
lda $2001,x
|
|
sta OPCODE_HIGH_SAVE+$2000,y
|
|
x02 lda $1000,x
|
|
sta OPCODE_SAVE+$1000,y
|
|
lda $1001,x
|
|
sta OPCODE_HIGH_SAVE+$1000,y
|
|
x01 lda: $0000,x
|
|
sta: OPCODE_SAVE+$0000,y
|
|
lda: $0001,x
|
|
sta: OPCODE_HIGH_SAVE+$0000,y
|
|
bottom
|
|
<<<
|
|
|
|
; RestoreOpcode
|
|
;
|
|
; Restore the values back to the code field.
|
|
;
|
|
; X = number of lines * 2, 0 to 32
|
|
; Y = starting line * $1000
|
|
; A = code field location * $1000
|
|
RestoreOpcode mac
|
|
jmp (dispTbl,x)
|
|
dispTbl da bottom
|
|
da do01,do02,do03,do04
|
|
da do05,do06,do07,do08
|
|
da do09,do10,do11,do12
|
|
da do13,do14,do15,do16
|
|
|
|
do15 tax
|
|
bra x15
|
|
do14 tax
|
|
bra x14
|
|
do13 tax
|
|
bra x13
|
|
do12 tax
|
|
bra x12
|
|
do11 tax
|
|
bra x11
|
|
do10 tax
|
|
bra x10
|
|
do09 tax
|
|
bra x09
|
|
do08 tax
|
|
bra x08
|
|
do07 tax
|
|
bra x07
|
|
do06 tax
|
|
bra x06
|
|
do05 tax
|
|
bra x05
|
|
do04 tax
|
|
bra x04
|
|
do03 tax
|
|
bra x03
|
|
do02 tax
|
|
bra x02
|
|
do01 tax
|
|
bra x01
|
|
do16 tax
|
|
x16 lda OPCODE_SAVE+$F000,y
|
|
sta $F000,x
|
|
x15 lda OPCODE_SAVE+$E000,y
|
|
sta $E000,x
|
|
x14 lda OPCODE_SAVE+$D000,y
|
|
sta $D000,x
|
|
x13 lda OPCODE_SAVE+$C000,y
|
|
sta $C000,x
|
|
x12 lda OPCODE_SAVE+$B000,y
|
|
sta $B000,x
|
|
x11 lda OPCODE_SAVE+$A000,y
|
|
sta $A000,x
|
|
x10 lda OPCODE_SAVE+$9000,y
|
|
sta $9000,x
|
|
x09 lda OPCODE_SAVE+$8000,y
|
|
sta $8000,x
|
|
x08 lda OPCODE_SAVE+$7000,y
|
|
sta $7000,x
|
|
x07 lda OPCODE_SAVE+$6000,y
|
|
sta $6000,x
|
|
x06 lda OPCODE_SAVE+$5000,y
|
|
sta $5000,x
|
|
x05 lda OPCODE_SAVE+$4000,y
|
|
sta $4000,x
|
|
x04 lda OPCODE_SAVE+$3000,y
|
|
sta $3000,x
|
|
x03 lda OPCODE_SAVE+$2000,y
|
|
sta $2000,x
|
|
x02 lda OPCODE_SAVE+$1000,y
|
|
sta $1000,x
|
|
x01 lda: OPCODE_SAVE+$0000,y
|
|
sta: $0000,x
|
|
bottom
|
|
<<<
|
|
|
|
; SetCodeEntry
|
|
;
|
|
; Patch in the low byte at the CODE_ENTRY. Must be called with 8-bit accumulator
|
|
;
|
|
; X = number of lines * 2, 0 to 32
|
|
; Y = starting line * $1000
|
|
; A = address low byte
|
|
SetCodeEntry mac
|
|
jmp (dispTbl,x)
|
|
dispTbl da bottom-00,bottom-03,bottom-06,bottom-09
|
|
da bottom-12,bottom-15,bottom-18,bottom-21
|
|
da bottom-24,bottom-27,bottom-30,bottom-33
|
|
da bottom-36,bottom-39,bottom-42,bottom-45
|
|
da bottom-48
|
|
sta CODE_ENTRY+$F000,y
|
|
sta CODE_ENTRY+$E000,y
|
|
sta CODE_ENTRY+$D000,y
|
|
sta CODE_ENTRY+$C000,y
|
|
sta CODE_ENTRY+$B000,y
|
|
sta CODE_ENTRY+$A000,y
|
|
sta CODE_ENTRY+$9000,y
|
|
sta CODE_ENTRY+$8000,y
|
|
sta CODE_ENTRY+$7000,y
|
|
sta CODE_ENTRY+$6000,y
|
|
sta CODE_ENTRY+$5000,y
|
|
sta CODE_ENTRY+$4000,y
|
|
sta CODE_ENTRY+$3000,y
|
|
sta CODE_ENTRY+$2000,y
|
|
sta CODE_ENTRY+$1000,y
|
|
sta: CODE_ENTRY+$0000,y
|
|
bottom
|
|
<<<
|
|
|
|
; SetOddCodeEntry
|
|
;
|
|
; Patch in the low byte at the ODD_ENTRY. Must be called with 8-bit accumulator
|
|
;
|
|
; X = number of lines * 2, 0 to 32
|
|
; Y = starting line * $1000
|
|
; A = address low byte
|
|
SetOddCodeEntry mac
|
|
jmp (dispTbl,x)
|
|
dispTbl da bottom-00,bottom-03,bottom-06,bottom-09
|
|
da bottom-12,bottom-15,bottom-18,bottom-21
|
|
da bottom-24,bottom-27,bottom-30,bottom-33
|
|
da bottom-36,bottom-39,bottom-42,bottom-45
|
|
da bottom-48
|
|
sta ODD_ENTRY+$F000,y
|
|
sta ODD_ENTRY+$E000,y
|
|
sta ODD_ENTRY+$D000,y
|
|
sta ODD_ENTRY+$C000,y
|
|
sta ODD_ENTRY+$B000,y
|
|
sta ODD_ENTRY+$A000,y
|
|
sta ODD_ENTRY+$9000,y
|
|
sta ODD_ENTRY+$8000,y
|
|
sta ODD_ENTRY+$7000,y
|
|
sta ODD_ENTRY+$6000,y
|
|
sta ODD_ENTRY+$5000,y
|
|
sta ODD_ENTRY+$4000,y
|
|
sta ODD_ENTRY+$3000,y
|
|
sta ODD_ENTRY+$2000,y
|
|
sta ODD_ENTRY+$1000,y
|
|
sta: ODD_ENTRY+$0000,y
|
|
bottom
|
|
<<<
|
|
|
|
; SetCodeEntryOpcode
|
|
;
|
|
; Patch in the opcode at the CODE_ENTRY_OPCODE. Must be called with 8-bit accumulator
|
|
;
|
|
; X = number of lines * 2, 0 to 32
|
|
; Y = starting line * $1000
|
|
; A = opcode value
|
|
SetCodeEntryOpcode mac
|
|
jmp (dispTbl,x)
|
|
dispTbl da bottom-00,bottom-03,bottom-06,bottom-09
|
|
da bottom-12,bottom-15,bottom-18,bottom-21
|
|
da bottom-24,bottom-27,bottom-30,bottom-33
|
|
da bottom-36,bottom-39,bottom-42,bottom-45
|
|
da bottom-48
|
|
sta CODE_ENTRY_OPCODE+$F000,y
|
|
sta CODE_ENTRY_OPCODE+$E000,y
|
|
sta CODE_ENTRY_OPCODE+$D000,y
|
|
sta CODE_ENTRY_OPCODE+$C000,y
|
|
sta CODE_ENTRY_OPCODE+$B000,y
|
|
sta CODE_ENTRY_OPCODE+$A000,y
|
|
sta CODE_ENTRY_OPCODE+$9000,y
|
|
sta CODE_ENTRY_OPCODE+$8000,y
|
|
sta CODE_ENTRY_OPCODE+$7000,y
|
|
sta CODE_ENTRY_OPCODE+$6000,y
|
|
sta CODE_ENTRY_OPCODE+$5000,y
|
|
sta CODE_ENTRY_OPCODE+$4000,y
|
|
sta CODE_ENTRY_OPCODE+$3000,y
|
|
sta CODE_ENTRY_OPCODE+$2000,y
|
|
sta CODE_ENTRY_OPCODE+$1000,y
|
|
sta: CODE_ENTRY_OPCODE+$0000,y
|
|
bottom
|
|
<<<
|