diff --git a/Flashing.md b/Flashing.md
index 289d54f..bdc9a66 100644
--- a/Flashing.md
+++ b/Flashing.md
@@ -1,81 +1,10 @@
 ## Users
 
+**NOTE: You probably want to use the updater!**
+
 Users of BlueSCSI should follow the instructions over at [BlueSCSI-Updater](https://github.com/erichelgeson/BlueSCSI-Updater) to update their devices.
 
+
 ## Developers
 
-These options are for developers and advanced users.
-
-When flashing you have two options:
-
-1. Flash by setting up the Visual Studio Code IDE, installing the ARM toolchain and PlatformIO extensions, and re-compiling and programming. If you are a developer and plan to contribute this method is what you should use.
-
-1. You may also flash the `.bin` file directly from [STM32CubeProgrammer](https://www.st.com/en/development-tools/stm32cubeprog.html). Use this method if you are not a developer and just wish to get the code to the BluePill.
-
-### Using STLink v2
-
-#### Setup STLinkV2
-
-Be sure to buy the "Clone" STLink V2 programmer - **the official STLink programmer does not work**.
-
-![stlink](https://user-images.githubusercontent.com/271734/160190399-a3275132-822e-42ad-894b-af20bde0e57f.png)
-
-* Make sure the STLinkV2 is up to date - [Latest Firmware](https://www.st.com/en/development-tools/stsw-link007.html)
-
-* Connect pins `SWDIO`, `GND`, `SWCLK`, and `3.3v` from the programmer to the Blue Pill.
-  * NOTE: These are not the same as Serial ports.
-
-#### Procedure (STM32CubeProgrammer)
-
-* Remove SD Card
-* Open STM32CubeProgrammer
-* Move the `BOOT0` jumper (furthest from the reset button) to `1`
-* Push the reset button on the BluePill
-* Click Connect in STM32CubeProgrammer
-* Select the .bin file and program.
-* Move `BOOT0` jumper back to 0
-* Push the reset button on the BluePill
-* You should see the LED `PC_13` flashing 5x indicating no SD Card detected.
-
-#### Procedure (PlatformIO)
-
-* Remove SD Card
-* Move the `BOOT0` jumper (furthest from the button switch) to `1`
-* Push the reset button on the BluePill
-* Run the [PlatformIO: Upload task](https://docs.platformio.org/en/latest/integration/ide/vscode.html#project-tasks).
-  * Expected output:
-```
-Uploading .pio/build/genericSTM32F103C8/firmware.elf
-xPack OpenOCD, x86_64 Open On-Chip Debugger 0.10.0+dev-00378-ge5be992df (2020-06-26-12:31)
-Licensed under GNU GPL v2
-For bug reports, read
-        http://openocd.org/doc/doxygen/bugs.html
-debug_level: 1
-
-0
-hla_swd
-target halted due to debug-request, current mode: Thread 
-xPSR: 0x01000000 pc: 0x08000194 msp: 0x20000690
-** Programming Started **
-** Programming Finished **
-** Verify Started **
-** Verified OK **.      <-- Everything flashed OK
-** Resetting Target **
-```
-* Move `BOOT0` jumper back to `0`
-* Push the reset switch on the BluePill
-* You should see the LED `PC_13` flashing 5x indicating no SD Card detected.
-
-The following YouTube video demonstrates the steps of flashing & updating your BlueSCSI https://www.youtube.com/watch?v=bRLAOts_MTM
-
-### Trouble Shooting
-
-Move the jumper furthest away from the `RESET` switch to 1. Reset and try to program again.
-
-If the device is not detected you may need to hold reset, click program, once it is detected release reset.
-
-If you are unable to get the device in DFU mode for programming you may need to use `STM32CubeProgrammer` to erase the chip.
-
-## Alternative upload methods
-
-See the [uploading documentation](https://docs.platformio.org/en/latest/boards/ststm32/bluepill_f103c8.html#uploading) on PlatformIO for alternatives.
\ No newline at end of file
+If you are a developer of BlueSCSI - advanced flashing instructions are here https://github.com/erichelgeson/BlueSCSI/wiki/Flashing-(Advanced)
\ No newline at end of file