mirror of
https://github.com/MiSTer-devel/MacPlus_MiSTer.git
synced 2024-11-23 06:32:16 +00:00
341 lines
10 KiB
Verilog
341 lines
10 KiB
Verilog
/* verilator lint_off UNUSED */
|
|
/* verilator lint_off SYNCASYNCNET */
|
|
|
|
// scsi.v
|
|
// implements a target only scsi device
|
|
|
|
module scsi
|
|
(
|
|
input clk,
|
|
|
|
// scsi interface
|
|
input rst, // bus reset from initiator
|
|
input sel,
|
|
input atn, // initiator requests to send a message
|
|
output bsy, // target holds bus
|
|
|
|
output msg,
|
|
output cd,
|
|
output io,
|
|
|
|
output req,
|
|
input ack, // initiator acknowledges a request
|
|
|
|
input [7:0] din, // data from initiator to target
|
|
output [7:0] dout, // data from target to initiator
|
|
|
|
// interface to io controller
|
|
output [31:0] io_lba,
|
|
output reg io_rd,
|
|
output reg io_wr,
|
|
input io_ack,
|
|
|
|
input [8:0] sd_buff_addr,
|
|
input [7:0] sd_buff_dout,
|
|
output reg [7:0] sd_buff_din,
|
|
input sd_buff_wr
|
|
);
|
|
|
|
|
|
// SCSI device id
|
|
parameter ID = 0;
|
|
|
|
`define PHASE_IDLE 3'd0
|
|
`define PHASE_CMD_IN 3'd1
|
|
`define PHASE_DATA_OUT 3'd2
|
|
`define PHASE_DATA_IN 3'd3
|
|
`define PHASE_STATUS_OUT 3'd4
|
|
`define PHASE_MESSAGE_OUT 3'd5
|
|
reg [2:0] phase;
|
|
|
|
// ---------------- buffer read engine -----------------------
|
|
// the buffer itself. Can hold one sector
|
|
reg [7:0] buffer_out [512];
|
|
always @(posedge clk) sd_buff_din <= buffer_out[sd_buff_addr];
|
|
|
|
// ---------------- buffer write engine ----------------------
|
|
// the buffer itself. Can hold one sector
|
|
reg [7:0] buffer_in [512];
|
|
always @(posedge clk) if(sd_buff_wr) buffer_in[sd_buff_addr] <= sd_buff_dout;
|
|
|
|
// -----------------------------------------------------------
|
|
|
|
// status replies
|
|
reg [7:0] status;
|
|
`define STATUS_OK 8'h00
|
|
`define STATUS_CHECK_CONDITION 8'h02
|
|
|
|
// message codes
|
|
`define MSG_CMD_COMPLETE 8'h00
|
|
|
|
// drive scsi signals according to phase
|
|
assign msg = (phase == `PHASE_MESSAGE_OUT);
|
|
assign cd = (phase == `PHASE_CMD_IN) || (phase == `PHASE_STATUS_OUT) || (phase == `PHASE_MESSAGE_OUT);
|
|
assign io = (phase == `PHASE_DATA_OUT) || (phase == `PHASE_STATUS_OUT) || (phase == `PHASE_MESSAGE_OUT);
|
|
assign req = (phase != `PHASE_IDLE) && !ack && !io_rd && !io_wr && !io_ack;
|
|
assign bsy = (phase != `PHASE_IDLE);
|
|
|
|
assign dout = (phase == `PHASE_STATUS_OUT)?status:
|
|
(phase == `PHASE_MESSAGE_OUT)?`MSG_CMD_COMPLETE:
|
|
(phase == `PHASE_DATA_OUT)?cmd_dout:
|
|
8'h00;
|
|
|
|
// de-multiplex different data sources
|
|
wire [7:0] cmd_dout =
|
|
cmd_read?buffer_dout:
|
|
cmd_inquiry?inquiry_dout:
|
|
cmd_read_capacity?read_capacity_dout:
|
|
cmd_mode_sense?mode_sense_dout:
|
|
8'h00;
|
|
|
|
// output of inquiry command, identify as "SEAGATE ST225N"
|
|
wire [7:0] inquiry_dout =
|
|
(data_cnt == 32'd4 )?8'd32: // length
|
|
|
|
(data_cnt == 32'd8 )?" ":(data_cnt == 32'd9 )?"S":
|
|
(data_cnt == 32'd10)?"E":(data_cnt == 32'd11)?"A":
|
|
(data_cnt == 32'd12)?"G":(data_cnt == 32'd13)?"A":
|
|
(data_cnt == 32'd14)?"T":(data_cnt == 32'd15)?"E":
|
|
(data_cnt == 32'd16)?" ":(data_cnt == 32'd17)?" ":
|
|
(data_cnt == 32'd18)?" ":(data_cnt == 32'd19)?" ":
|
|
(data_cnt == 32'd20)?" ":(data_cnt == 32'd21)?" ":
|
|
(data_cnt == 32'd22)?" ":(data_cnt == 32'd23)?" ":
|
|
(data_cnt == 32'd24)?" ":(data_cnt == 32'd25)?" ":
|
|
|
|
(data_cnt == 32'd26)?"S":(data_cnt == 32'd27)?"T":
|
|
(data_cnt == 32'd28)?"2":(data_cnt == 32'd29)?"2":
|
|
(data_cnt == 32'd30)?"5":(data_cnt == 32'd31)?"N":
|
|
8'h00;
|
|
|
|
// output of read capacity command
|
|
wire [31:0] capacity = 32'd41056; // 40960 + 96 blocks = 20MB
|
|
wire [31:0] capacity_m1 = capacity - 32'd1;
|
|
wire [7:0] read_capacity_dout =
|
|
(data_cnt == 32'd0 )?capacity_m1[31:24]:
|
|
(data_cnt == 32'd1 )?capacity_m1[23:16]:
|
|
(data_cnt == 32'd2 )?capacity_m1[15:8]:
|
|
(data_cnt == 32'd3 )?capacity_m1[7:0]:
|
|
(data_cnt == 32'd6 )?8'd2: // 512 bytes per sector
|
|
8'h00;
|
|
|
|
wire [7:0] mode_sense_dout =
|
|
(data_cnt == 32'd3 )?8'd8:
|
|
(data_cnt == 32'd5 )?capacity[23:16]:
|
|
(data_cnt == 32'd6 )?capacity[15:8]:
|
|
(data_cnt == 32'd7 )?capacity[7:0]:
|
|
(data_cnt == 32'd10 )?8'd2:
|
|
8'h00;
|
|
|
|
// clock data out of buffer to allow for embedded ram
|
|
reg [7:0] buffer_dout;
|
|
always @(posedge clk) buffer_dout <= buffer_in[data_cnt];
|
|
|
|
// buffer to store incoming commands
|
|
reg [3:0] cmd_cnt;
|
|
reg [7:0] cmd [9:0];
|
|
|
|
/* ----------------------- request data from/to io controller ----------------------- */
|
|
|
|
// base address of current block. Subtract one when writing since the writing happens
|
|
// after a block has been transferred and data_cnt has thus already been increased by 512
|
|
assign io_lba = lba + { 9'd0, data_cnt[31:9] } -
|
|
(cmd_write ? 32'd1 : 32'd0);
|
|
|
|
wire req_rd = ((phase == `PHASE_DATA_OUT) && cmd_read && (data_cnt[8:0] == 0) && !data_complete);
|
|
wire req_wr = ((((phase == `PHASE_DATA_IN) && (data_cnt[8:0] == 0) && (data_cnt != 0)) || (phase == `PHASE_STATUS_OUT)) && cmd_write);
|
|
always @(posedge clk) begin
|
|
reg old_rd, old_wr;
|
|
|
|
old_rd <= req_rd;
|
|
old_wr <= req_wr;
|
|
|
|
if(io_ack) begin
|
|
io_rd <= 1'b0;
|
|
io_wr <= 1'b0;
|
|
end else begin
|
|
// generate an io_rd signal whenever the first byte of a 512 byte block is required and io_wr whenever
|
|
// the last byte of a 512 byte block has been revceived
|
|
if(~old_rd & req_rd) io_rd <= 1;
|
|
|
|
// generate an io_wr signal whenever a 512 byte block has been received or when the status
|
|
// phase of a write command has been reached
|
|
if(~old_wr & req_wr) io_wr <= 1;
|
|
end
|
|
end
|
|
|
|
reg stb_ack;
|
|
reg stb_adv;
|
|
always @(posedge clk) begin
|
|
reg old_ack;
|
|
|
|
old_ack <= ack;
|
|
stb_ack <= (~old_ack & ack);
|
|
stb_adv <= stb_ack;
|
|
end
|
|
|
|
// store data on rising edge of ack, ...
|
|
always @(posedge clk) begin
|
|
if(stb_ack) begin
|
|
if(phase == `PHASE_CMD_IN) cmd[cmd_cnt] <= din;
|
|
if(phase == `PHASE_DATA_IN) buffer_out[data_cnt] <= din;
|
|
end
|
|
end
|
|
|
|
// ... advance counter on falling edge
|
|
always @(posedge clk) begin
|
|
if(phase == `PHASE_IDLE) cmd_cnt <= 4'd0;
|
|
else if(stb_adv && (phase == `PHASE_CMD_IN) && (cmd_cnt != 15)) cmd_cnt <= cmd_cnt + 4'd1;
|
|
end
|
|
|
|
// count data bytes. don't increase counter while we are waiting for data from
|
|
// the io controller
|
|
reg [31:0] data_cnt;
|
|
reg data_complete;
|
|
|
|
// For block transfers tlen contains the number of 512 bytes blocks to transfer.
|
|
// Most other commands have the bytes length stored in the transfer length field.
|
|
// And some have a fixed length idependent from any header field.
|
|
// The data transfer has finished once the data counter reaches this
|
|
// number.
|
|
wire [31:0] data_len =
|
|
cmd_read_capacity?32'd8:
|
|
cmd_read?{ 7'd0, tlen, 9'd0 }: // read command length is in 512 bytes blocks
|
|
cmd_write?{ 7'd0, tlen, 9'd0 }: // write command length is in 512 bytes blocks
|
|
{ 16'd0, tlen }; // inquiry etc have length in bytes
|
|
|
|
always @(posedge clk) begin
|
|
if((phase != `PHASE_DATA_OUT) && (phase != `PHASE_DATA_IN) && (phase != `PHASE_STATUS_OUT) && (phase != `PHASE_MESSAGE_OUT)) begin
|
|
data_cnt <= 0;
|
|
data_complete <= 0;
|
|
end else begin
|
|
if(stb_adv)begin
|
|
if(!data_complete) data_cnt <= data_cnt + 1'd1;
|
|
data_complete <= (data_len - 1'd1) == data_cnt;
|
|
end
|
|
end
|
|
end
|
|
|
|
// check whether status byte has been sent
|
|
reg status_sent;
|
|
always @(posedge clk) begin
|
|
if(phase != `PHASE_STATUS_OUT) status_sent <= 0;
|
|
else if(stb_adv) status_sent <= 1;
|
|
end
|
|
|
|
// check whether message byte has been sent
|
|
reg message_sent;
|
|
always @(posedge clk) begin
|
|
if(phase != `PHASE_MESSAGE_OUT) message_sent <= 0;
|
|
else if(stb_adv) message_sent <= 1;
|
|
end
|
|
|
|
/* ----------------------- command decoding ------------------------------- */
|
|
|
|
|
|
// parse commands
|
|
wire [7:0] op_code = cmd[0];
|
|
wire [2:0] cmd_group = op_code[7:5];
|
|
|
|
// check if a complete command has been received
|
|
wire cmd_cpl = cmd6_cpl || cmd10_cpl;
|
|
wire cmd6_cpl = (cmd_group == 3'b000) && (cmd_cnt == 6);
|
|
wire cmd10_cpl = ((cmd_group == 3'b010) || (cmd_group == 3'b001)) && (cmd_cnt == 10);
|
|
|
|
// https://en.wikipedia.org/wiki/SCSI_command
|
|
wire cmd_read = cmd_read6 || cmd_read10;
|
|
wire cmd_read6 = (op_code == 8'h08);
|
|
wire cmd_read10 = (op_code == 8'h28);
|
|
wire cmd_write = cmd_write6 || cmd_write10;
|
|
wire cmd_write6 = (op_code == 8'h0a);
|
|
wire cmd_write10 = (op_code == 8'h2a);
|
|
wire cmd_inquiry = (op_code == 8'h12);
|
|
wire cmd_format = (op_code == 8'h04);
|
|
wire cmd_mode_select = (op_code == 8'h15);
|
|
wire cmd_mode_sense = (op_code == 8'h1a);
|
|
wire cmd_test_unit_ready = (op_code == 8'h00);
|
|
wire cmd_read_capacity = (op_code == 8'h25);
|
|
|
|
// valid command in buffer? TODO: check for valid command parameters
|
|
wire cmd_ok = cmd_read || cmd_write || cmd_inquiry || cmd_test_unit_ready ||
|
|
cmd_read_capacity || cmd_mode_select || cmd_format || cmd_mode_sense;
|
|
|
|
// latch parameters once command is complete
|
|
reg [31:0] lba;
|
|
reg [15:0] tlen;
|
|
|
|
always @(posedge clk) begin
|
|
if(cmd_cpl && (phase == `PHASE_CMD_IN)) begin
|
|
lba <= cmd6_cpl?{11'd0, lba6}:lba10;
|
|
tlen <= cmd6_cpl?{7'd0, tlen6}:tlen10;
|
|
end
|
|
end
|
|
|
|
// logical block address
|
|
wire [7:0] cmd1 = cmd[1];
|
|
wire [20:0] lba6 = { cmd1[4:0], cmd[2], cmd[3] };
|
|
wire [31:0] lba10 = { cmd[2], cmd[3], cmd[4], cmd[5] };
|
|
|
|
// transfer length
|
|
wire [8:0] tlen6 = (cmd[4] == 0)?9'd256:{1'b0,cmd[4]};
|
|
wire [15:0] tlen10 = { cmd[7], cmd[8] };
|
|
|
|
|
|
// the 5380 changes phase in the falling edge, thus we monitor it
|
|
// on the rising edge
|
|
always @(posedge clk) begin
|
|
if(rst) begin
|
|
phase <= `PHASE_IDLE;
|
|
end else begin
|
|
if(phase == `PHASE_IDLE) begin
|
|
if(sel && din[ID]) // own id on bus during selection?
|
|
phase <= `PHASE_CMD_IN;
|
|
end
|
|
|
|
else if(phase == `PHASE_CMD_IN) begin
|
|
// check if a full command is in the buffer
|
|
if(cmd_cpl) begin
|
|
// is this a supported and valid command?
|
|
if(cmd_ok) begin
|
|
// yes, continue
|
|
status <= `STATUS_OK;
|
|
|
|
// continue according to command
|
|
|
|
// these commands return data
|
|
if(cmd_read || cmd_inquiry || cmd_read_capacity || cmd_mode_sense) phase <= `PHASE_DATA_OUT;
|
|
// these commands receive dataa
|
|
else if(cmd_write || cmd_mode_select) phase <= `PHASE_DATA_IN;
|
|
// and all other valid commands are just "ok"
|
|
else phase <= `PHASE_STATUS_OUT;
|
|
end else begin
|
|
// no, report failure
|
|
status <= `STATUS_CHECK_CONDITION;
|
|
phase <= `PHASE_STATUS_OUT;
|
|
end
|
|
end
|
|
end
|
|
|
|
else if(phase == `PHASE_DATA_OUT) begin
|
|
if(data_complete) phase <= `PHASE_STATUS_OUT;
|
|
end
|
|
|
|
else if(phase == `PHASE_DATA_IN) begin
|
|
if(data_complete) phase <= `PHASE_STATUS_OUT;
|
|
end
|
|
|
|
else if(phase == `PHASE_STATUS_OUT) begin
|
|
if(status_sent) phase <= `PHASE_MESSAGE_OUT;
|
|
end
|
|
|
|
else if(phase == `PHASE_MESSAGE_OUT) begin
|
|
if(message_sent) phase <= `PHASE_IDLE;
|
|
end
|
|
|
|
else
|
|
phase <= `PHASE_IDLE; // should never happen
|
|
end
|
|
end
|
|
|
|
|
|
endmodule
|