RASCSI/cpp/hal/gpiobus_raspberry.h
Uwe Seimet 31be1b3e8f Use standard C++ timer for long timeouts (#1327), remove unused code (#1328)
* Replace timer in WaitSignal()

' Remove unused code

* Remove unused file
2024-05-01 16:15:42 +09:00

287 lines
9.0 KiB
C++
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

//---------------------------------------------------------------------------
//
// SCSI Target Emulator PiSCSI
// for Raspberry Pi
//
// Powered by XM6 TypeG Technology.
// Copyright (C) 2016-2020 GIMONS
// [ GPIO-SCSI bus ]
//
//---------------------------------------------------------------------------
#pragma once
#include "hal/data_sample_raspberry.h"
#include "hal/gpiobus.h"
#include "shared/scsi.h"
#include <map>
//---------------------------------------------------------------------------
//
// SCSI signal pin assignment setting
// GPIO pin mapping table for SCSI signals.
// PIN_DT0PIN_SEL
//
//---------------------------------------------------------------------------
#define ALL_SCSI_PINS \
((1 << PIN_DT0) | (1 << PIN_DT1) | (1 << PIN_DT2) | (1 << PIN_DT3) | (1 << PIN_DT4) | (1 << PIN_DT5) | \
(1 << PIN_DT6) | (1 << PIN_DT7) | (1 << PIN_DP) | (1 << PIN_ATN) | (1 << PIN_RST) | (1 << PIN_ACK) | \
(1 << PIN_REQ) | (1 << PIN_MSG) | (1 << PIN_CD) | (1 << PIN_IO) | (1 << PIN_BSY) | (1 << PIN_SEL))
#define GPIO_INEDGE ((1 << PIN_BSY) | (1 << PIN_SEL) | (1 << PIN_ATN) | (1 << PIN_ACK) | (1 << PIN_RST))
#define GPIO_MCI ((1 << PIN_MSG) | (1 << PIN_CD) | (1 << PIN_IO))
//---------------------------------------------------------------------------
//
// Constant declarations (GIC)
//
//---------------------------------------------------------------------------
const static uint32_t ARM_GICD_BASE = 0xFF841000;
const static uint32_t ARM_GICC_BASE = 0xFF842000;
const static uint32_t ARM_GIC_END = 0xFF847FFF;
const static int GICD_CTLR = 0x000;
const static int GICD_IGROUPR0 = 0x020;
const static int GICD_ISENABLER0 = 0x040;
const static int GICD_ICENABLER0 = 0x060;
const static int GICD_ISPENDR0 = 0x080;
const static int GICD_ICPENDR0 = 0x0A0;
const static int GICD_ISACTIVER0 = 0x0C0;
const static int GICD_ICACTIVER0 = 0x0E0;
const static int GICD_IPRIORITYR0 = 0x100;
const static int GICD_ITARGETSR0 = 0x200;
const static int GICD_ICFGR0 = 0x300;
const static int GICD_SGIR = 0x3C0;
const static int GICC_CTLR = 0x000;
const static int GICC_PMR = 0x001;
const static int GICC_IAR = 0x003;
const static int GICC_EOIR = 0x004;
//---------------------------------------------------------------------------
//
// Constant declarations (GIC IRQ)
//
//---------------------------------------------------------------------------
const static int GIC_IRQLOCAL0 = (16 + 14);
const static int GIC_GPIO_IRQ = (32 + 116); // GPIO3
//---------------------------------------------------------------------------
//
// Class definition
//
//---------------------------------------------------------------------------
class GPIOBUS_Raspberry : public GPIOBUS
{
public:
GPIOBUS_Raspberry() = default;
~GPIOBUS_Raspberry() override = default;
bool Init(mode_e mode = mode_e::TARGET) override;
void Reset() override;
void Cleanup() override;
// Bus signal acquisition
uint32_t Acquire() override;
// Set ENB signal
void SetENB(bool ast) override;
// Get BSY signal
bool GetBSY() const override;
// Set BSY signal
void SetBSY(bool ast) override;
// Get SEL signal
bool GetSEL() const override;
// Set SEL signal
void SetSEL(bool ast) override;
// Get ATN signal
bool GetATN() const override;
// Set ATN signal
void SetATN(bool ast) override;
// Get ACK signal
bool GetACK() const override;
// Set ACK signal
void SetACK(bool ast) override;
// Get ACT signal
bool GetACT() const override;
// Set ACT signal
void SetACT(bool ast) override;
// Get RST signal
bool GetRST() const override;
// Set RST signal
void SetRST(bool ast) override;
// Get MSG signal
bool GetMSG() const override;
// Set MSG signal
void SetMSG(bool ast) override;
// Get CD signal
bool GetCD() const override;
// Set CD signal
void SetCD(bool ast) override;
// Get IO signal
bool GetIO() override;
// Set IO signal
void SetIO(bool ast) override;
// Get REQ signal
bool GetREQ() const override;
// Set REQ signal
void SetREQ(bool ast) override;
// Get DAT signal
uint8_t GetDAT() override;
// Set DAT signal
void SetDAT(uint8_t dat) override;
bool WaitREQ(bool ast) override
{
return WaitSignal(PIN_REQ, ast);
}
bool WaitACK(bool ast) override
{
return WaitSignal(PIN_ACK, ast);
}
static uint32_t bcm_host_get_peripheral_address();
unique_ptr<DataSample> GetSample(uint64_t timestamp) override
{
Acquire();
return make_unique<DataSample_Raspberry>(signals, timestamp);
}
protected:
// All bus signals
uint32_t signals = 0;
// GPIO input level
volatile uint32_t *level = nullptr;
private:
// SCSI I/O signal control
void MakeTable() override;
// Create work data
void SetControl(int pin, bool ast) override;
// Set Control Signal
void SetMode(int pin, int mode) override;
// Set SCSI I/O mode
bool GetSignal(int pin) const override;
// Get SCSI input signal value
void SetSignal(int pin, bool ast) override;
// Set SCSI output signal value
// Interrupt control
void DisableIRQ() override;
// IRQ Disabled
void EnableIRQ() override;
// IRQ Enabled
// GPIO pin functionality settings
void PinConfig(int pin, int mode) override;
// GPIO pin direction setting
void PullConfig(int pin, int mode) override;
// GPIO pin pull up/down resistor setting
void PinSetSignal(int pin, bool ast) override;
// Set GPIO output signal
void DrvConfig(uint32_t drive) override;
// Set GPIO drive strength
static uint32_t get_dt_ranges(const char *filename, uint32_t offset);
uint32_t baseaddr = 0; // Base address
int rpitype = 0; // Type of Raspberry Pi
// GPIO register
volatile uint32_t *gpio = nullptr; // NOSONAR: volatile needed for register access
// PADS register
volatile uint32_t *pads = nullptr; // NOSONAR: volatile needed for register access
// Interrupt control register
volatile uint32_t *irpctl = nullptr;
// Interrupt enabled state
volatile uint32_t irptenb; // NOSONAR: volatile needed for register access
// QA7 register
volatile uint32_t *qa7regs = nullptr;
// Interupt control target CPU.
volatile int tintcore; // NOSONAR: volatile needed for register access
// Interupt control
volatile uint32_t tintctl; // NOSONAR: volatile needed for register access
// GICC priority setting
volatile uint32_t giccpmr; // NOSONAR: volatile needed for register access
#if !defined(__x86_64__) && !defined(__X86__)
// GIC Interrupt distributor register
volatile uint32_t *gicd = nullptr;
#endif
// GIC CPU interface register
volatile uint32_t *gicc = nullptr;
// RAM copy of GPFSEL0-4 values (GPIO Function Select)
array<uint32_t, 4> gpfsel;
#if SIGNAL_CONTROL_MODE == 0
// Data mask table
array<array<uint32_t, 256>, 3> tblDatMsk;
// Data setting table
array<array<uint32_t, 256>, 3> tblDatSet;
#else
// Data mask table
array<uint32_t, 256> tblDatMsk = {};
// Table setting table
array<uint32_t, 256> tblDatSet = {};
#endif
static const array<int, 19> SignalTable;
const static int GPIO_FSEL_0 = 0;
const static int GPIO_FSEL_1 = 1;
const static int GPIO_FSEL_2 = 2;
const static int GPIO_FSEL_3 = 3;
const static int GPIO_SET_0 = 7;
const static int GPIO_CLR_0 = 10;
const static int GPIO_LEV_0 = 13;
const static int GPIO_EDS_0 = 16;
const static int GPIO_REN_0 = 19;
const static int GPIO_FEN_0 = 22;
const static int GPIO_HEN_0 = 25;
const static int GPIO_LEN_0 = 28;
const static int GPIO_AREN_0 = 31;
const static int GPIO_AFEN_0 = 34;
const static int GPIO_PUD = 37;
const static int GPIO_CLK_0 = 38;
const static int GPIO_GPPINMUXSD = 52;
const static int GPIO_PUPPDN0 = 57;
const static int GPIO_PUPPDN1 = 58;
const static int GPIO_PUPPDN3 = 59;
const static int GPIO_PUPPDN4 = 60;
const static int PAD_0_27 = 11;
const static int IRPT_PND_IRQ_B = 0;
const static int IRPT_PND_IRQ_1 = 1;
const static int IRPT_PND_IRQ_2 = 2;
const static int IRPT_FIQ_CNTL = 3;
const static int IRPT_ENB_IRQ_1 = 4;
const static int IRPT_ENB_IRQ_2 = 5;
const static int IRPT_ENB_IRQ_B = 6;
const static int IRPT_DIS_IRQ_1 = 7;
const static int IRPT_DIS_IRQ_2 = 8;
const static int IRPT_DIS_IRQ_B = 9;
const static int QA7_CORE0_TINTC = 16;
const static int GPIO_IRQ = (32 + 20); // GPIO3
const static uint32_t IRPT_OFFSET = 0x0000B200;
const static uint32_t PADS_OFFSET = 0x00100000;
const static uint32_t GPIO_OFFSET = 0x00200000;
const static uint32_t QA7_OFFSET = 0x01000000;
};