SCSI2SD/CHANGELOG
2017-03-12 14:15:05 +10:00

170 lines
6.8 KiB
Plaintext

20170312 4.7
- Fix bug in SCSI Inquiry command for SCSI2 hosts
- Added OMTI host quirks mode
- Fix for booting from early Mac Plus ROMS
- Performance fix when SCSI2 mode is enabled. Some users may need
to disable SCSI2 mode if it was incorrectly enabled previously.
- Added support for configurable mode pages
- Fix for exporting selectionDelay/startupDelay parameters to XML
via scsi2sd-util
- scsi2sd-util is now built with libudev1 on Linux, as all distros have
moved to this version. Users on older Linux distributions will need to
compile from source.
20160111 4.6
- Fixed bug when using sector size that isn't a multiple of 4
(eg. 522 bytes)
- Fixed a bug that caused hanging or scsi phase errors on
high speed scsi hosts.
- Fixed a hang when processing a SCSI RESET in a data phase.
- scsi2sd-util: Fixed USB connection problems under Windows 10.
- Added option to treat luns as separate devices
- Improved boot up time.
20151105 4.5
- Fix bug in SCSI MODE SENSE that returned the wrong mode type
- Fixes CDROM emulation
- Added selection delay parameter. This should be set to 1ms for older
SCSI1 hardware, or 0ms for SCSI2 and Mac Plus.
- Upgraded to wxWidgets 3.0.2
- Fixed stability/performance issue for sector sizes above 512
- Fixed bug that prevented the dvice working after "ejecting" a drive
- Upgraded to Cypress PSoC Creator 3.3
- Added experimental caching option. This provides a 2x speed up for
sequential single-sector writes. It is disabled by default.
- Disabled SCSI Disconnect support by default. There's now an option
in scsi2sd-util to enable it. It should be left off unless you have
a very good reason to enable it.
20150813 4.4
- Added configuration option to allow SCSI2 mode. This option is OFF by
default, and should only be enabled when using the SCSI2SD with a SCSI2 host
controller. Extra timing delays are added in the default SCSI1/SASI mode to
work with slow hardware.
- Modified hot-swap card detection to work with longer (60cm) microSD to SD
cables.
- Fixed off-by-one error in scsi2sd-util "Auto" sector start feature.
- Fixed crashes and stalls of scsi2sd-util after saving/loading options
to/from the device
- Fixed synchronous transfer request negotiation.
SCSI2SD now negotiates back to async transfers instead of simply
rejecting the message.
- Fixed INQUIRY response to commands lacking an allocation length.
- Firmware development updated to PSoC Creator 3.2 (from 3.1)
20150614 4.3
- Added configurable disk geometry.
- Added configuration import/export function to scsi2sd-util
- scsi2sd-util stability fixes
- Fixes to support EMU EMAX1 & 2
20150504 4.2.4
- Clean up version number mishap (4.2.3 reported as 4.2.2)
- Reduce size of mode pages for SCSI1 hosts
- Stability improvements whan handling resets during SCSI reads.
20150420 4.2.3
- Bugfix for failed flash checksums after configing configuration
20150420 4.2.2
- Improved compatibility with older SCSI1 hosts.
20150123 4.1.1
- Fix MODE SENSE bug when the allocation length is less than the
page size.
- Add WRITE BUFFER and WRITE AND VERIFY support.
- Fix rare case of very slow performance
20150201 4.1
- Rewrite of the SD card interface to fix compatibility problems.
This fixes write issues with Samsung SD cards.
- Workaround for SCSI hosts that set 250ms timeouts. Some NCR53C80/53C9X
drivers (openbsd, netbsd, and others) set a byte-to-byte timeout which
can be exceeded by SD card latency.
- Upgrade to PSoC Creator 3.1 and gcc 4.8.4.
- Integrated scsi2sd-debug functionality with scsi2sd-util.
20150108 4.0
- Fix handling requests for LUNs other than 0 from SCSI-2 hosts.
- Handle glitches of the scsi signals to improve stability and operate with
multiple devices on the SCSI bus.
- Re-add parity checking. This can be disabled using scsi2sd-config if
required.
- Added disconnect/reconnect support during SD card writes.
- Preliminary CDROM device support (incomplete)
- New configuration method. Data is now stored in flash to allow room for
custom VPD tables. The old eeprom configuration is ignored.
- Support for up to 4 SCSI targets.
- scsi2sd-config and bootloader hosts utilities are replaced by the
new scsi2sd-util GUI.
- Fix for SD cards with Samsung controllers which expect a "stop" bit
in each SD command over SPI.
- Hot-swap support. The SD card can be removed whenever it's not in use
(ie. the LED must be OFF when the SD card is removed)
20140718 3.5.2
- Fix blank SCSI ID in scsi2sd-config output.
20140717 3.5.1
- Allow building utilities on older Linux distros
- Resolve missing DLL issues for the Windows utilities
- Fix scsi2sd-config crash on Mac.
20140713 3.5
- Fixed several performance issues. Transfer rates up to 2.5MB/s are now
possible.
- Implemented the READ BUFFER scsi command for performance testing purposes.
- Added support for the new "yellow" v4.2 revision boards.
- Improved firmware uploading. bootloaderhost can now reset the board back
to the bootloader.
- Display firmware version in scsi2sd-config
- Add "--reset" parameter to scsi2sd-config
20140418 3.4
- Critical fix for writes when using non-standard block sizes.
- Fix to ensure SCSI phase bits are set atomically.
- Always return the requested number of bytes for a REQUEST SENSE command
This is required to support the Ensoniq ASR-10.
- Decreased (unused) heap and stack sizes to prepare for a memory
write cache
- Increased the maximum sector size to 8192 bytes.
20140416 3.3
- Fix to SCSI Reset handling to avoid lockups
- Bug fixes to improve standards compatibility
- Bug fix for Unit Attention Condition, which is now enabled by default.
scsi2sd-config can be used to disable it for those systems that
truely require it (eg. Mac Plus).
- Added Linked commands support.
- Added support for configurable sector sizes between 64 and 2048 bytes.
The sector size can be set via the MODE SELECT command using a SCSI
format utility, or via scsi2sd-config
- Powerbook firmware added
20140214 3.2
- Remove hacks around ATN handling, and implement proper select-with-atn
support. This fix is essential for communicating with some SCSI hosts.
All SCSI2SD users are urged to upgrade to this firmware version.
- More fixes to support Apple HD SC Setup (thanks to Doug Brown!)
- Fixes to support SCSI1 initiators
* Support non-arbitrating initiators.
* Support single-initiator option.
* Set CCS response format flag in INQUIRY response.
20131227 3.1
- Fixes for better SCSI reset handling
- Fix for reading the last sector of the SD card.
- Performance improvements. 2.5x read, 2x write performance.
20131209 3.0.1
- Bugfix release.
- Fixes to support formatting with Apple HD SC Setup. This is very slow,
Apple Drive Setup is preferred
- Reliability improvement for rejecting unknown SCSI messages.
- Reliability improvements for SD card initialisation and reading.
20131027 3.0
- Initial public release.