Release 14.7 Map P.20131013 (nt) Xilinx Mapping Report File for Design 'WarpLC' Design Information ------------------ Command Line : map -intstyle ise -p xc6slx9-ftg256-2 -w -logic_opt off -ol high -t 1 -xt 0 -register_duplication off -r 4 -global_opt off -mt off -ir off -pr off -lc off -power off -o WarpLC_map.ncd WarpLC.ngd WarpLC.pcf Target Device : xc6slx9 Target Package : ftg256 Target Speed : -2 Mapper Version : spartan6 -- $Revision: 1.55 $ Mapped Date : Fri Oct 29 10:02:57 2021 Design Summary -------------- Number of errors: 0 Number of warnings: 1 Slice Logic Utilization: Number of Slice Registers: 56 out of 11,440 1% Number used as Flip Flops: 56 Number used as Latches: 0 Number used as Latch-thrus: 0 Number used as AND/OR logics: 0 Number of Slice LUTs: 59 out of 5,720 1% Number used as logic: 56 out of 5,720 1% Number using O6 output only: 24 Number using O5 output only: 29 Number using O5 and O6: 3 Number used as ROM: 0 Number used as Memory: 0 out of 1,440 0% Number used exclusively as route-thrus: 3 Number with same-slice register load: 2 Number with same-slice carry load: 1 Number with other load: 0 Slice Logic Distribution: Number of occupied Slices: 25 out of 1,430 1% Number of MUXCYs used: 56 out of 2,860 1% Number of LUT Flip Flop pairs used: 76 Number with an unused Flip Flop: 22 out of 76 28% Number with an unused LUT: 17 out of 76 22% Number of fully used LUT-FF pairs: 37 out of 76 48% Number of unique control sets: 4 Number of slice register sites lost to control set restrictions: 16 out of 11,440 1% A LUT Flip Flop pair for this architecture represents one LUT paired with one Flip Flop within a slice. A control set is a unique combination of clock, reset, set, and enable signals for a registered element. The Slice Logic Distribution report is not meaningful if the design is over-mapped for a non-slice resource or if Placement fails. IO Utilization: Number of bonded IOBs: 49 out of 186 26% IOB Flip Flops: 5 IOB Latches: 1 Specific Feature Utilization: Number of RAMB16BWERs: 0 out of 32 0% Number of RAMB8BWERs: 0 out of 64 0% Number of BUFIO2/BUFIO2_2CLKs: 1 out of 32 3% Number used as BUFIO2s: 1 Number used as BUFIO2_2CLKs: 0 Number of BUFIO2FB/BUFIO2FB_2CLKs: 1 out of 32 3% Number used as BUFIO2FBs: 1 Number used as BUFIO2FB_2CLKs: 0 Number of BUFG/BUFGMUXs: 3 out of 16 18% Number used as BUFGs: 3 Number used as BUFGMUX: 0 Number of DCM/DCM_CLKGENs: 0 out of 4 0% Number of ILOGIC2/ISERDES2s: 1 out of 200 1% Number used as ILOGIC2s: 1 Number used as ISERDES2s: 0 Number of IODELAY2/IODRP2/IODRP2_MCBs: 0 out of 200 0% Number of OLOGIC2/OSERDES2s: 5 out of 200 2% Number used as OLOGIC2s: 5 Number used as OSERDES2s: 0 Number of BSCANs: 0 out of 4 0% Number of BUFHs: 0 out of 128 0% Number of BUFPLLs: 0 out of 8 0% Number of BUFPLL_MCBs: 0 out of 4 0% Number of DSP48A1s: 0 out of 16 0% Number of ICAPs: 0 out of 1 0% Number of MCBs: 0 out of 2 0% Number of PCILOGICSEs: 0 out of 2 0% Number of PLL_ADVs: 1 out of 2 50% Number of PMVs: 0 out of 1 0% Number of STARTUPs: 0 out of 1 0% Number of SUSPEND_SYNCs: 0 out of 1 0% Average Fanout of Non-Clock Nets: 2.16 Peak Memory Usage: 272 MB Total REAL time to MAP completion: 4 secs Total CPU time to MAP completion: 4 secs Table of Contents ----------------- Section 1 - Errors Section 2 - Warnings Section 3 - Informational Section 4 - Removed Logic Summary Section 5 - Removed Logic Section 6 - IOB Properties Section 7 - RPMs Section 8 - Guide Report Section 9 - Area Group and Partition Summary Section 10 - Timing Report Section 11 - Configuration String Information Section 12 - Control Set Information Section 13 - Utilization by Hierarchy Section 1 - Errors ------------------ Section 2 - Warnings -------------------- WARNING:Security:43 - No license file was found in the standard Xilinx license directory. WARNING:Security:44 - Since no license file was found, WARNING:Security:40 - Your license for 'ISE' expires in 4 days. WARNING:MapLib:53 - The offset specification "OFFSET=IN 10000 pS VALID 11000 pS BEFORE FSBCLK" has been discarded because the referenced clock pad net (FSBCLK) was optimized away. Section 3 - Informational ------------------------- INFO:Security:51 - The XILINXD_LICENSE_FILE environment variable is not set. INFO:Security:52 - The LM_LICENSE_FILE environment variable is set to 'C:\ispLEVER_Classic2_0\license\license.dat;C:\lscc\diamond\3.12\license\license .dat;C:\Xilinx\14.7\ISE_DS\Xilinx.lic'. INFO:Security:54 - 'xc6slx9' is a WebPack part. INFO:Security:66 - Your license for 'ISE' is for evaluation use only. INFO:LIT:243 - Logical network FSB_A<0> has no load. INFO:LIT:395 - The above info message is repeated 120 more times for the following (max. 5 shown): FSB_SIZ<1>, FSB_SIZ<0>, IOB_nDSACK<1>, IOB_nDSACK<0>, CPU_nCIOUT To see the details of these info messages, please use the -detail switch. INFO:MapLib:562 - No environment variables are currently set. INFO:MapLib:159 - Net Timing constraints on signal CLKIN are pushed forward through input buffer. INFO:Pack:1716 - Initializing temperature to 85.000 Celsius. (default - Range: 0.000 to 85.000 Celsius) INFO:Pack:1720 - Initializing voltage to 1.140 Volts. (default - Range: 1.140 to 1.260 Volts) INFO:Map:215 - The Interim Design Summary has been generated in the MAP Report (.mrp). INFO:Pack:1650 - Map created a placed design. Section 4 - Removed Logic Summary --------------------------------- 2 block(s) optimized away Section 5 - Removed Logic ------------------------- Optimized Block(s): TYPE BLOCK GND XST_GND VCC XST_VCC To enable printing of redundant blocks removed and signals merged, set the detailed map report option and rerun map. Section 6 - IOB Properties -------------------------- +---------------------------------------------------------------------------------------------------------------------------------------------------------+ | IOB Name | Type | Direction | IO Standard | Diff | Drive | Slew | Reg (s) | Resistor | IOB | | | | | | Term | Strength | Rate | | | Delay | +---------------------------------------------------------------------------------------------------------------------------------------------------------+ | CLKFB_IN | IOB | INPUT | LVCMOS25 | | | | | | | | CLKFB_OUT | IOB | OUTPUT | LVCMOS33 | | 24 | FAST | ODDR | | | | CLKIN | IOB | INPUT | LVCMOS25 | | | | | | | | CPUCLK | IOB | OUTPUT | LVCMOS33 | | 24 | FAST | OFF | | | | CPUCLKIN | IOB | INPUT | LVCMOS33 | | | | | | | | CPU_nAS | IOB | INPUT | LVCMOS33 | | | | | | | | CPU_nBERR | IOB | OUTPUT | LVCMOS33 | | 2 | SLOW | OFF | | | | CPU_nDSACK | IOB | OUTPUT | LVCMOS33 | | 24 | FAST | | | | | CPU_nSTERM | IOB | OUTPUT | LVCMOS33 | | 24 | FAST | | | | | FPUCLK | IOB | OUTPUT | LVCMOS33 | | 24 | FAST | OFF | | | | FSB_A<1> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<2> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<3> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<4> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<5> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<6> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<7> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<8> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<9> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<10> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<11> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<12> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<13> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<14> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<15> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<16> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<17> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<18> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<19> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<20> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<21> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<22> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<23> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<24> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<25> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<26> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<27> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<28> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<29> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<30> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_A<31> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_FC<0> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_FC<1> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_FC<2> | IOB | INPUT | LVCMOS33 | | | | | | | | FSB_RnW | IOB | INPUT | LVCMOS33 | | | | | | | | IOB_nHALT | IOB | INPUT | LVCMOS33 | | | | ILATCH | | | | RAM_CLK01 | IOB | OUTPUT | LVCMOS33 | | 24 | FAST | ODDR | | | | nFPUCS | IOB | OUTPUT | LVCMOS33 | | 24 | FAST | | | | | nRESOE | IOB | OUTPUT | LVCMOS33 | | 2 | QUIE | | | | +---------------------------------------------------------------------------------------------------------------------------------------------------------+ Section 7 - RPMs ---------------- Section 8 - Guide Report ------------------------ Guide not run on this design. Section 9 - Area Group and Partition Summary -------------------------------------------- Partition Implementation Status ------------------------------- No Partitions were found in this design. ------------------------------- Area Group Information ---------------------- No area groups were found in this design. ---------------------- Section 10 - Timing Report -------------------------- A logic-level (pre-route) timing report can be generated by using Xilinx static timing analysis tools, Timing Analyzer (GUI) or TRCE (command line), with the mapped NCD and PCF files. Please note that this timing report will be generated using estimated delay information. For accurate numbers, please generate a timing report with the post Place and Route NCD file. For more information about the Timing Analyzer, consult the Xilinx Timing Analyzer Reference Manual; for more information about TRCE, consult the Xilinx Command Line Tools User Guide "TRACE" chapter. Section 11 - Configuration String Details ----------------------------------------- Use the "-detail" map option to print out Configuration Strings Section 12 - Control Set Information ------------------------------------ Use the "-detail" map option to print out Control Set Information. Section 13 - Utilization by Hierarchy ------------------------------------- Use the "-detail" map option to print out the Utilization by Hierarchy section.