mirror of
https://github.com/dkgrizzly/GreenSCSI.git
synced 2024-11-21 12:31:20 +00:00
Delete docs directory
This commit is contained in:
David Kuder
GitHub
parent
12743b6fb8
commit
d5a6ac0b9c
@ -1,27 +0,0 @@
|
||||
# BlueSCSI 1.0-b to 1.0-c
|
||||
:toc: macro
|
||||
|
||||
## Introduction
|
||||
|
||||
1.0-c was a small change to fix an issue with machines that provide low or no `TERMPOWER` over the SCSI bus. If you recived a Fully Assembled BlueSCSI after April 1st, 2021 then this was done for you. If you have a kit labled 1.0-b you can make these modifications to become a 1.0-c.
|
||||
|
||||
## Steps
|
||||
|
||||
### Disconnect `TERMPOWER` from 220 Pull Up Jupmer
|
||||
|
||||
Use a cutting tool to cut the small trace between the `TERMPOWR` and 220 Pull Up Jumper pictured below.
|
||||
|
||||
Make sure continiutiy from `TERMPOWER` to the diode still flows correctly but is disconnected from the jumper.
|
||||
|
||||
image::images/1.0-b-bodge-1.jpg[]
|
||||
|
||||
### Connect 5V to 220 Pull Up Jupmer
|
||||
|
||||
Now we will provide pull up from the 5v provided by the BluePill.
|
||||
|
||||
image::images/1.0-b-bodge-2.png[]
|
||||
|
||||
### Complete!
|
||||
|
||||
Thats it! 5v to the Pull Up resistors will now work when powered externally.
|
||||
|
||||
BIN
docs/MacHD.zip
BIN
docs/MacHD.zip
Binary file not shown.
@ -1 +0,0 @@
|
||||
BlueSCSI Documentation © 2021 by Eric Helgeson is licensed under Attribution-NonCommercial 4.0 International
|
||||
@ -1,66 +0,0 @@
|
||||
# Assembly
|
||||
|
||||
## Before you start
|
||||
|
||||
Read through all instructions before starting.
|
||||
|
||||
## Videos
|
||||
|
||||
The community has created a few assembly videos:
|
||||
* [Stephen Arsenault - BlueSCSI Kit Assembly](https://www.youtube.com/watch?v=G6lwCfLQwd8) 2:52
|
||||
* [Joe's Computer Museum - A New Challenger - BlueSCSI - #MARCHintosh Review](https://www.youtube.com/watch?v=d_8VVmvvlNI) 26:52
|
||||
* [Geeky Bit - Tutorial - BlueSCSI Assembly](https://www.youtube.com/watch?v=-nF9FYFgVHM) 20:35
|
||||
|
||||
## Building
|
||||
|
||||
1. Solder on the surface mount SD Card holder. Use the [Drag Solder](https://youtu.be/Z_KL4fWOMug) technique.
|
||||
- Once on, check continuity of all connections. Fixing this after the BluePill is on will be difficult.
|
||||
- Ensure the SD card fits and you dont have too much solder on the sides or contacts
|
||||
2. Solder the diodes to the **bottom** of the board. Be sure they are flush as possible to the bottom.
|
||||
|
||||
3. Solder the header pins on to the BluePill. Then BluePill pill to the BlueSCSI PCB.
|
||||
- Correct orientation is having the USB connector of the BluePill should be over the SD Card holder.
|
||||
- **NOTE**: Consider adding headers to the board if you would like to have the BluePill removable.
|
||||
4. Solder on the resistor nets. Pin one is marked on the board and the resistors.
|
||||
- 220 RNETS (`RN1` & `RN3`) are closest to the BluePill
|
||||
- **NOTE** PIN one on each - they are opposite of eachtoher. See photo.
|
||||
- 330 RNETS (`RN2` & `RN4`) are furthest from the BluePill
|
||||
- **NOTE** PIN one on each - they are opposite of eachtoher. See photo.
|
||||
|
||||
5. Solder on the Termination Jumpers & place the jumpers on to enable Termiation
|
||||
6. Solder the 50 Pin headers on.
|
||||
1. Note Pin 1 and Box header on the silk screen.
|
||||
7. Optional - Solder on the berg connector. Only needed if your machine does not supply enough power via the SCSI bus.
|
||||
8. Optional - Solder on the debug headers near the SD card. Only nessissarry if re-programming.
|
||||
|
||||
### Fully Assembled
|
||||
|
||||
|
||||
### Version 1.0-b & 1.0-c BOM
|
||||
|
||||
#### Mouser Cart
|
||||
|
||||
https://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=c5cc83feff
|
||||
|
||||
#### Parts
|
||||
|
||||
STM32F103C8T6 (U1) aka BluePill board. Beware of fake/scams. Look for reviews. Amazon, ebay, etc.
|
||||
|
||||
* 2x 330 (RN2, RN4) Resistor nets https://www.mouser.com/ProductDetail/652-4610X-1LF-330
|
||||
|
||||
* 2x 220 (RN1, RN3) Resistor nets https://www.mouser.com/ProductDetail/652-4610X-1LF-220
|
||||
|
||||
* 2x Diodes https://www.mouser.com/ProductDetail/583-1N5818-T
|
||||
|
||||
* SD Card Holder (J1) https://www.mouser.com/ProductDetail/538-104031-0811
|
||||
|
||||
* Headers https://www.mouser.com/ProductDetail/872-920-0011-01
|
||||
|
||||
* 50 PIN SCSI header https://www.mouser.com/ProductDetail/517-30350-6002/
|
||||
- May substitute with 2 rows of headers from above.
|
||||
- **Note on Right angle connectors** - it appears Right angle headers are notched differently then the pin out. Be sure to note PIN 1/red stripe on the cable match up.
|
||||
|
||||
### Optional
|
||||
|
||||
Floppy/Berg Power header https://www.mouser.com/ProductDetail/571-1718254
|
||||
- Required if your machine does not supply power via TERM POWER. For example a Mac Plus or Mac with a Analog/PSU board that has not been recapped.
|
||||
@ -1,60 +0,0 @@
|
||||
|
||||
# Build Your Own
|
||||
|
||||
These instructions will guide you thorugh purchasing all of the parts needed to assemble kits for yourselves and for friends! Please note the hardware is licensed non-comercial.
|
||||
|
||||
If you'd like to buy the kits pre-packaged/pre-flashed or fully assembled we have a network of makers here to help you out at https://scsi.blue
|
||||
|
||||
## Order Parts
|
||||
|
||||
Updated for 1.0-c.
|
||||
|
||||
### PCB's
|
||||
|
||||
Grab the latest Gerbers. Gerber files tell the PCB manufactuer how to create the BlueSCSI boards.
|
||||
|
||||
https://github.com/erichelgeson/BlueSCSI/tree/main/hw/gerbers
|
||||
|
||||
Order the boards from https://jlcpcb.com/ or your manufactuer of choice.
|
||||
|
||||
### Components
|
||||
|
||||
#### Version 1.0-b & 1.0-c BOM
|
||||
|
||||
https://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=c5cc83feff
|
||||
|
||||
### BluePill
|
||||
|
||||
Beware of fakes and buy from a place where returns are easy. Ensure the photo in the listing shows a chip that says STM32 on it.
|
||||
|
||||
https://www.amazon.com/s?k=stm32f103c8t6
|
||||
|
||||
https://www.ebay.com/sch/i.html?_nkw=stm32f103c8t6
|
||||
|
||||
### STlinkV2
|
||||
|
||||
You can usually find these bundled with the bluepill or at the same store you bought your bluepill.
|
||||
|
||||
## Assemble
|
||||
|
||||
Follow the guide on component orientation and assembly.
|
||||
|
||||
https://github.com/erichelgeson/BlueSCSI/blob/main/docs/assembly.md
|
||||
|
||||
## 3D Case
|
||||
|
||||
Print or order a 3D case for your BlueSCSI to mount it inside your computer.
|
||||
|
||||
https://github.com/erichelgeson/BlueSCSI/tree/main/3D-Files
|
||||
|
||||
## Flash
|
||||
|
||||
You will need to flash the BlueSCSI program onto your BluePill following these instructions.
|
||||
|
||||
https://github.com/erichelgeson/BlueSCSI#flashing
|
||||
|
||||
## Usage
|
||||
|
||||
Be sure to follow the usage instructions for getting your drive images setup:
|
||||
|
||||
https://github.com/erichelgeson/BlueSCSI#usage
|
||||
BIN
docs/buynow.png
BIN
docs/buynow.png
Binary file not shown.
|
Before Width: | Height: | Size: 20 KiB |
Binary file not shown.
|
Before Width: | Height: | Size: 22 KiB |
Binary file not shown.
|
Before Width: | Height: | Size: 2.3 MiB |
Binary file not shown.
|
Before Width: | Height: | Size: 213 KiB |
Binary file not shown.
|
Before Width: | Height: | Size: 1.3 MiB |
Binary file not shown.
|
Before Width: | Height: | Size: 743 KiB |
Binary file not shown.
|
Before Width: | Height: | Size: 17 MiB |
Binary file not shown.
|
Before Width: | Height: | Size: 488 KiB |
@ -1,26 +0,0 @@
|
||||
# Troubleshooting 1.0-b
|
||||
:toc: macro
|
||||
|
||||
NOTE: If your BlueSCSI was shipped after April 3rd, 2021 please refer to the 1.0-c troubleshooting guide.
|
||||
|
||||
## Green LED Flashes on and off
|
||||
|
||||
This indicates BlueSCSI could not find any files on the SD card or communicate with the SD card.
|
||||
|
||||
Ensure your files are named properly (case sensitive) following the naming convetion in the readme.
|
||||
|
||||
If you recived a kit - verify all connections and that the outside of the SD holder is grounded.
|
||||
|
||||
## LOG.txt is empty
|
||||
|
||||
This indicates the BlueSCSI could communicate with the SD Card but found no files. Check your naming convention.
|
||||
|
||||
## Slow performance
|
||||
|
||||
Ensure you are using a good SD card. SD card quality can vary widely.
|
||||
|
||||
Format your card as ExFat - users have seen quite a jump in performance.
|
||||
|
||||
## (Kit Only) Verify you are not using a fake
|
||||
|
||||
https://github.com/keirf/Greaseweazle/wiki/STM32-Fakes[How to tell if your STM32 is fake]
|
||||
Loading…
Reference in New Issue
Block a user