added README for Quack X esp_8_bit

2024-12-12 00:29:06 +00:00 · 2024-08-29 12:47:02 +02:00 · 2024-08-29 12:47:02 +02:00 · 9f8d71fcea
commit 9f8d71fcea
parent bcc7802439
1 changed files with 165 additions and 0 deletions
--- a/Misc/esp_8_bit/README.md
+++ b/Misc/esp_8_bit/README.md
@ -0,0 +1,165 @@
+# Quack X esp_8_bit
+This is a crossover between two projects, that allow you to mod a Quack board to use with esp_8_bit firmware.
+The result is a two players small box that can contains a few NES games and fit near your TV.
+
+![quack+esp_8_bit](https://github.com/demik/quack/blob/master/Misc/esp_8_bit/quack%2Besp_8_bit.jpeg)
+
+this is unsupported (outside of the quack project) and the parent project (esp_8_bit) is likely dead so this will likely not receive any updates or fixes
+
+- parent project: [rossumur/esp_8_bit](https://github.com/rossumur/esp_8_bit)
+- used patches from: [CornN64/esp_8_bit](https://github.com/CornN64/esp_8_bit)
+
+it supports two players (one hardwired, either NES or SNES) and one Wiimote based. Unlike other builds, the hardwired connector runs at +5V (uses both level converters of the quack board), which allow the use of retro wireless adapters
+
+schematic:
+
+```
+    -----------
+    |         |
+    |      25 |----------------------------------> video out
+    |         |
+    |         |   ------------
+    |       2 |---| LVC 4245 |----/\/\/\/----|---> audio out
+    |         |   ------------      1kΩ      |
+    |         |                             ---
+    |         |                             --- 10nF
+    |  ESP32  |                              |
+    |         |                              v gnd
+    |         |
+    |         |   ------------
+    |       4 |---| LVC 2T45 |---< NES (or SNES) controller DATA
+    |         |   ------------
+    |         |   ------------
+    |      12 |---| LVC 4245 |---> NES (or SNES) controller CLOCK
+    |      14 |---| LVC 4245 |---> NES (or SNES) controller LATCH
+    |         |   ------------
+    |         |            5v <--> NES (or SNES) controller VCC
+    |         |           gnd <--> NES (or SNES) controller GND
+    |         |
+    -----------
+
+
+NES        ___
+    DATA  |o o| NC
+    LATCH |o o| NC
+    CLOCK |o o/ 5V
+    GND   |o_/
+
+SNES       _
+    5V    |o|
+    CLOCK |o|
+    LATCH |o|
+    DATA  |o|
+          |-|
+    NC    |o|
+    NC    |o|
+    GND   |o|
+           -
+
+```
+
+## Software
+
+Since the esp_8_bit source code is old, you will need an old IDE (Arduino 1.8.14 with esp board 1.0.4)
+
+there is a couple of patches in this directory that you will need to patch on top of [rossumur/esp_8_bit](https://github.com/rossumur/esp_8_bit)
+
+- base.diff integrates patches from [CornN64/esp_8_bit](https://github.com/CornN64/esp_8_bit) and enable quack specific features (pinout, LEDs, DIP switches)
+- controller.diff removes IR support, clean code and adds (S)NES controller support
+
+```
+> git clone https://github.com/rossumur/esp_8_bit.git
+Cloning into 'esp_8_bit'...
+remote: Enumerating objects: 345, done.
+remote: Counting objects: 100% (15/15), done.
+remote: Compressing objects: 100% (10/10), done.
+remote: Total 345 (delta 5), reused 5 (delta 5), pack-reused 330 (from 1)
+Receiving objects: 100% (345/345), 8.01 MiB | 8.04 MiB/s, done.
+Resolving deltas: 100% (108/108), done.
+> cd esp_8_bit
+> patch -p1 < ../base.diff
+patching file README.md
+patching file esp_8_bit.ino
+patching file 'src/emu.cpp'
+patching file 'src/emu.h'
+patching file 'src/emu_nofrendo.cpp'
+patching file 'src/gui.cpp'
+patching file 'src/hid_server/hid_server.cpp'
+patching file 'src/video_out.h'
+> patch -p1 < ../controller.diff
+patching file 'src/ir_input.h'
+patching file 'src/nintendo.h'
+```
+
+To avoid [this issue](https://github.com/rossumur/esp_8_bit/issues/19) you may want to change the partition layout as well. Check the solution into that issue, and also the boards.txt and quack_8_bit.csv if needed
+
+###
+
+## Hardware
+
+This mod is compatible with board revision 1.3 and 1.4
+
+### PCB mods
+
+hardware modifications needed
+
+- remove Q1
+- remove FB9
+- remove D1
+- bridge R1 or replace by 0Ω
+- remove the Mini DIN-4 connector
+
+Under the board:
+
+- connect a wire from DE-9 pin 6 to D1 pin (+) on top of the board
+- connect a wire from DE-9 pin 8 to Mini DIN-4 pin 1
+
+![bodge](https://github.com/demik/quack/blob/master/Misc/esp_8_bit/bodge.png)
+
+### Adapter cable
+
+You will need a NES or SNES extension cable, one triple RCA video cable, one USB cable (charge only is OK) and one DE-9 solderable connector
+RC filtering circuit will be integrated into the connector. pinout is a follow (board side)
+
+```
+   _____________________
+  /                     \
+  \  1   2   3   4   5  /
+   \   6   7   8   9   /
+    \_________________/
+```
+
+| Pin | Connection | Notes |
+|---|---|---|
+| 1 | Ground | power ground & RCA shields here |
+| 2 | +5V | USB +5V and (S)NES +5V connector go here |
+| 3 | Ground | (S)NES ground + 10nF capacitor ground |
+| 4 | NC | unused |
+| 5 | Clock | (S)NES controller clock |
+| 6 | Video | composite video out, yellow RCA |
+| 7 | Sound | one pin of the 1kΩ resistor |
+| 8 | Data | (S)NES controller data |
+| 9 | Latch | (S)NES controller data |
+| R | Resistor | solder capacitor on the other resistor pin & white + red RCA (+) wires |
+
+isolate everything with hot glue or better
+
+## Usage
+
+Nothing different than the parent project as far as emulation goes
+
+### Switches
+
+Quack set of dip switches allows for the following settings
+
+- ADB Host: (S)NES controller is player A, Wiimote player B or the other way around
+- Bluetooth Disable: Kill BT Operation if not needed. More stable / less noise. Use with ADB Host to ON
+- Flash: flash mode (GPIO0 to GND)
+
+### LED
+
+PCB LEDs are usable and do have basic functionality
+
+- green: init done, board powered up
+- yellow: valid (S)NES controller input received
+- red: embedded flash operation in progress