An interface for the DCD protocol used by Apple's Hard Disk 20.
Go to file
lampmerchant a32ea1b892 20211122
2021-11-22 20:41:23 -07:00
firmware 20211122 2021-11-22 20:41:23 -07:00
LICENSE Initial commit 2021-11-03 13:53:20 -06:00
README.md Update README.md 2021-11-14 19:32:33 -07:00

tashtwenty

An interface bridging the DCD protocol used by Apple's Hard Disk 20 to a MMC card, implemented using a PIC16F1825.

MMC Card Format

The contents of the first 512-byte sector of the MMC card are reported as the Controller Status block. In this way, the user can customize details such as the icon and size of the disk. The first 512-byte sector on the disk is mapped to the second 512-byte sector of the MMC card, the second sector on the disk to the third on the card, and so forth.

DCD (Directly Connected Disks) Protocol

Details Missing or Inaccurate in the May 1985 DCD Document

  • The sync byte, in either direction, is always 0xAA, 0x96 is not used.
  • When Mac is transmitting a command, the sync byte is followed by two more raw IWM bytes before the 7-to-8 groups begin. DCD transmits only a sync byte and does not transmit these extra bytes.
    • The first is 0x80 plus the number of 7-to-8 groups in the command being transmitted by Mac.
    • The second is 0x80 plus the number of 7-to-8 groups that Mac expects to receive in response.
  • The holdoff protocol is completely different than specified.
    • In either direction, a holdoff is initiated by Mac transitioning from state 1 to state 0.
    • If Mac is transmitting, it will finish the 7-to-8 group that it has begun transmitting. This data is valid.
    • If DCD is transmitting, it must finish the 7-to-8 group that it has begun transmitting. This data will be treated by Mac as valid.
    • A holdoff is ended by Mac transitioning from state 0 to state 1. There is no negotiation.
    • If Mac is transmitting and WR is high at the end of the last byte transmitted before holdoff, it will transition WR from high to low right before transitioning back to state 1.
    • Mac will resume transmission with an 0xAA byte, followed by the bytes in the next group after the group where the holdoff began.
    • DCD must resume transmission with an 0xAA byte, followed by the bytes in the next group after the group where the holdoff began.
  • The Controller Status (command 0x03) block is slightly different than specified.
    • The total size of the Controller Status block is 336 bytes, not 532 bytes.
      • 336 bytes of data, 6 byte header, checksum byte == 343 bytes == 49 7-to-8 groups
    • The Icon field contains a 32x32 icon as a 1-bit bitmap, followed by its 32x32 mask, also as a 1-bit bitmap, for a total of 256 bytes.
      • The format of the bitmaps is identical to that of ICON resources.
    • The Filler field is replaced by a 16-byte Pascal string (first byte is length) that determines what appears in the "Where:" field of the Get Info dialog box.
  • The checksum byte is chosen such that all data bytes in all 7-to-8 groups (not including the sync byte or the command/response length IWM bytes) sum to 0 modulo 256.

Details Out of Scope for DCD Documentation But Useful to Know

  • The IWM transmits and receives MSB first and the MSB is always set; the chip uses this for timing.
  • The IWM transmits at its "fast" speed, 47/96 MHz, or approximately 489.58 Kbps, data cell width 2.043 us.
  • The IWM's output (on WR pin) is in NRZI format (inversion == 1, no inversion == 0).
  • The IWM's input (on RD pin) detects only falling edges.

Beyond

Other details about the protocol at the signal level and the read, write, and controller status commands are accurately reported by the May 1985 document; other commands are unknown to me, but hopefully this information will be useful to anyone in the future who wishes to implement DCD.