/**************************************************************************//** * @file clk_reg.h * @version V1.00 * @brief CLK register definition header file * * SPDX-License-Identifier: Apache-2.0 * @copyright (C) 2020 Nuvoton Technology Corp. All rights reserved. *****************************************************************************/ #ifndef __CLK_REG_H__ #define __CLK_REG_H__ #if defined ( __CC_ARM ) #pragma anon_unions #endif /** @addtogroup REGISTER Control Register @{ */ /** @addtogroup CLK System Clock Controller (CLK) Memory Mapped Structure for CLK Controller @{ */ typedef struct { /** * @var CLK_T::PWRCTL * Offset: 0x00 System Power-down Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |HXTEN |HXT Enable Bit (Write Protect) * | | |The bit default value is set by flash controller user configuration register CONFIG0 [26] * | | |When the default clock source is from HXT, this bit is set to 1 automatically. * | | |0 = 4~32 MHz external high speed crystal (HXT) Disabled. * | | |1 = 4~32 MHz external high speed crystal (HXT) Enabled. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[1] |LXTEN |LXT Enable Bit (Write Protect) * | | |0 = 32.768 kHz external low speed crystal (LXT) Disabled. * | | |1 = 32.768 kHz external low speed crystal (LXT) Enabled. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[2] |HIRCEN |HIRC Enable Bit (Write Protect) * | | |0 = 48MHz internal high speed RC oscillator (HIRC) Disabled. * | | |1 = 48 MHz internal high speed RC oscillator (HIRC) Enabled. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[3] |LIRCEN |LIRC Enable Bit (Write Protect) * | | |0 = 38.4 kHz internal low speed RC oscillator (LIRC) Disabled. * | | |1 = 38.4 kHz internal low speed RC oscillator (LIRC) Enabled. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * | | |Note : LIRC will also be forced on when 1 * | | |Power down and ~(cfg0[3] & cfg0[4] & ~cfg0[31] & cfg0[30]) 2 * | | |Not power down and ~(cfg0[3] & cfg0[4] & cfg0[31]) * |[4] |PDWKDLY |Enable the Wake-up Delay Counter (Write Protect) * | | |When the chip wakes up from Power-down mode, the clock control will delay certain clock cycles to wait system clock stable. * | | |The delayed clock cycle is 4096 clock cycles when chip works at 4~32 MHz external high speed crystal oscillator (HXT), HIRC and MIRC see HIRCSTBS and MIRCSTBS * | | |0 = Clock cycles delay Disabled. * | | |1 = Clock cycles delay Enabled. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[5] |PDWKIEN |Power-down Mode Wake-up Interrupt Enable Bit (Write Protect) * | | |0 = Power-down mode wake-up interrupt Disabled. * | | |1 = Power-down mode wake-up interrupt Enabled. * | | |Note1: The interrupt will occur when both PDWKIF and PDWKIEN are high. * | | |Note2: This bit is write protected. Refer to the SYS_REGLCTL register. * |[6] |PDWKIF |Power-down Mode Wake-up Interrupt Status * | | |Set by "Power-down wake-up event", it indicates that resume from Power-down mode. * | | |The flag is set if any wake-up source is occurred. Refer Power Modes and Wake-up Sources chapter. * | | |Note1: Write 1 to clear the bit to 0. * | | |Note2: This bit works only if PDWKIEN (CLK_PWRCTL[5]) set to 1. * |[7] |PDEN |System Power-down Enable (Write Protect) * | | |When this bit is set to 1, Power-down mode is enabled and chip Power-down behavior will depend on the PDWTCPU bit. * | | |(a) If the PDWTCPU is 0, then the chip enters Power-down mode immediately after the PDEN bit set * | | |(default) * | | |(b) if the PDWTCPU is 1, then the chip keeps active till the CPU sleep mode is also active and then the chip enters Power-down mode. * | | |When chip wakes up from Power-down mode, this bit is auto cleared * | | |Users need to set this bit again for next Power-down. * | | |In Power-down mode, HXT and the HIRC will be disabled in this mode, but LXT and LIRC are not controlled by Power-down mode. * | | |In Power-down mode, the PLL and system clock are disabled, and ignored the clock source selection * | | |The clocks of peripheral are not controlled by Power-down mode, if the peripheral clock source is from LXT or LIRC. * | | |0 = Chip operating normally or chip in idle mode because of WFI command. * | | |1 = Chip enters Power-down mode instant or wait CPU sleep command WFI. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[19] |MIRCEN |MIRC Enable Bit (Write Protect) * | | |0 = 4MHz internal high speed RC oscillator (MIRC) Disabled. * | | |1 = 4 MHz internal high speed RC oscillator (MIRC) Enabled. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * | | |Note: Will be forced on when CLKSEL0[2:0] = 0x101b. * |[22:20] |HXTGAIN |HXT Gain Control Bit (Write Protect) * | | |This is a protected register. Please refer to open lock sequence to program it. * | | |Gain control is used to enlarge the gain of crystal to make sure crystal work normally * | | |If gain control is enabled, crystal will consume more power than gain control off. * | | |000 = HXT frequency 1~4 MHz. * | | |001 = HXT frequency 4~8 MHz. * | | |010 = HXT frequency 8~12 MHz. * | | |011 = HXT frequency 12~16 MHz. * | | |100 = HXT frequency 12~24 MHz. * | | |101 = HXT frequency 16~32 MHz. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * | | |Note : reset by power on reset * @var CLK_T::AHBCLK * Offset: 0x04 AHB Devices Clock Enable Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[1] |PDMACKEN |PDMA Controller Clock Enable Bit * | | |0 = PDMA peripheral clock Disabled. * | | |1 = PDMA peripheral clock Enabled. * |[2] |ISPCKEN |Flash ISP Controller Clock Enable Bit * | | |0 = Flash ISP peripheral clock Disabled. * | | |1 = Flash ISP peripheral clock Enabled. * |[3] |EBICKEN |EBI Controller Clock Enable Bit * | | |0 = EBI peripheral clock Disabled. * | | |1 = EBI peripheral clock Enabled. * |[4] |EXSTCKEN |External System Tick Clock Enable Bit * | | |0 = External System tick clock Disabled. * | | |1 = External System tick clock Enabled. * |[7] |CRCCKEN |CRC Generator Controller Clock Enable Bit * | | |0 = CRC peripheral clock Disabled. * | | |1 = CRC peripheral clock Enabled. * |[12] |CRPTCKEN |Cryptographic Accelerator Clock Enable Bit * | | |0 = Cryptographic Accelerator clock Disabled. * | | |1 = Cryptographic Accelerator clock Enabled. * |[15] |FMCIDLE |Flash Memory Controller Clock Enable Bit in IDLE Mode * | | |0 = FMC clock Disabled when chip is under IDLE mode. * | | |1 = FMC clock Enabled when chip is under IDLE mode. * |[24] |GPACKEN |GPIOA Clock Enable Bit * | | |0 = GPIOA port clock Disabled. * | | |1 = GPIOA port clock Enabled. * |[25] |GPBCKEN |GPIOB Clock Enable Bit * | | |0 = GPIOB port clock Disabled. * | | |1 = GPIOB port clock Enabled. * |[26] |GPCCKEN |GPIOC Clock Enable Bit * | | |0 = GPIOC port clock Disabled. * | | |1 = GPIOC port clock Enabled. * |[27] |GPDCKEN |GPIOD Clock Enable Bit * | | |0 = GPIOD port clock Disabled. * | | |1 = GPIOD port clock Enabled. * |[28] |GPECKEN |GPIOE Clock Enable Bit * | | |0 = GPIOE port clock Disabled. * | | |1 = GPIOE port clock Enabled. * |[29] |GPFCKEN |GPIOF Clock Enable Bit * | | |0 = GPIOF port clock Disabled. * | | |1 = GPIOF port clock Enabled. * @var CLK_T::APBCLK0 * Offset: 0x08 APB Devices Clock Enable Control Register 0 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |WDTCKEN |Watchdog Timer Clock Enable Bit (Write Protect) * | | |0 = Watchdog timer clock Disabled. * | | |1 = Watchdog timer clock Enabled. * | | |Note 1: This bit is write protected. Refer to the SYS_REGLCTL register. * | | |Note 2: This bit is forced to 1 when CONFIG0[3] or CONFIG0[4] or CONFIG0[31] is 0. * | | |Note 3: Reset by power on reset or watch dog reset or software chip reset. * |[1] |RTCCKEN |Real-time-clock APB Interface Clock Enable Bit * | | |0 = RTC APB clock Disabled. * | | |1 = RTC APB clock Enabled. * |[2] |TMR0CKEN |Timer0 Clock Enable Bit * | | |0 = Timer0 clock Disabled. * | | |1 = Timer0 clock Enabled. * |[3] |TMR1CKEN |Timer1 Clock Enable Bit * | | |0 = Timer1 clock Disabled. * | | |1 = Timer1 clock Enabled. * |[4] |TMR2CKEN |Timer2 Clock Enable Bit * | | |0 = Timer2 clock Disabled. * | | |1 = Timer2 clock Enabled. * |[5] |TMR3CKEN |Timer3 Clock Enable Bit * | | |0 = Timer3 clock Disabled. * | | |1 = Timer3 clock Enabled. * |[6] |CLKOCKEN |CLKO Clock Enable Bit * | | |0 = CLKO clock Disabled. * | | |1 = CLKO clock Enabled. * |[7] |ACMP01CKEN|Analog Comparator 0/1 Clock Enable Bit * | | |0 = Analog comparator 0/1 clock Disabled. * | | |1 = Analog comparator 0/1 clock Enabled. * |[8] |I2C0CKEN |I2C0 Clock Enable Bit * | | |0 = I2C0 clock Disabled. * | | |1 = I2C0 clock Enabled. * |[9] |I2C1CKEN |I2C1 Clock Enable Bit * | | |0 = I2C1 clock Disabled. * | | |1 = I2C1 clock Enabled. * |[12] |QSPI0CKEN |QSPI0 Clock Enable Bit * | | |0 = QSPI0 clock Disabled. * | | |1 = QSPI0 clock Enabled. * |[13] |SPI0CKEN |SPI0 Clock Enable Bit * | | |0 = SPI0 clock Disabled. * | | |1 = SPI0 clock Enabled. * |[16] |UART0CKEN |UART0 Clock Enable Bit * | | |0 = UART0 clock Disabled. * | | |1 = UART0 clock Enabled. * |[17] |UART1CKEN |UART1 Clock Enable Bit * | | |0 = UART1 clock Disabled. * | | |1 = UART1 clock Enabled. * |[18] |UART2CKEN |UART2 Clock Enable Bit * | | |0 = UART2 clock Disabled. * | | |1 = UART2 clock Enabled. * |[27] |USBDCKEN |USB Device Clock Enable Bit * | | |0 = USB Device clock Disabled. * | | |1 = USB Device clock Enabled. * |[28] |EADCCKEN |Enhanced Analog-digital-converter (EADC) Clock Enable Bit * | | |0 = EADC clock Disabled. * | | |1 = EADC clock Enabled. * @var CLK_T::APBCLK1 * Offset: 0x0C APB Devices Clock Enable Control Register 1 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |SC0CKEN |SC0 Clock Enable Bit * | | |0 = SC0 clock Disabled. * | | |1 = SC0 clock Enabled. * |[8] |USCI0CKEN |USCI0 Clock Enable Bit * | | |0 = USCI0 clock Disabled. * | | |1 = USCI0 clock Enabled. * |[9] |USCI1CKEN |USCI1 Clock Enable Bit * | | |0 = USCI1 clock Disabled. * | | |1 = USCI1 clock Enabled. * |[10] |USCI2CKEN |USCI2 Clock Enable Bit * | | |0 = USCI1 clock Disabled. * | | |1 = USCI1 clock Enabled. * |[12] |DACCKEN |DAC Clock Enable Bit * | | |0 = DAC clock Disabled. * | | |1 = DAC clock Enabled. * |[16] |PWM0CKEN |PWM0 Clock Enable Bit * | | |0 = PWM0 clock Disabled. * | | |1 = PWM0 clock Enabled. * |[17] |PWM1CKEN |PWM1 Clock Enable Bit * | | |0 = PWM1 clock Disabled. * | | |1 = PWM1 clock Enabled. * |[18] |BPWM0CKEN |BPWM0 Clock Enable Bit * | | |0 = BPWM0 clock Disabled. * | | |1 = BPWM0 clock Enabled. * |[19] |BPWM1CKEN |BPWM1 Clock Enable Bit * | | |0 = BPWM1 clock Disabled. * | | |1 = BPWM1 clock Enabled. * |[30] |OPACKEN |OP Amplifier (OPA) Clock Enable Bit * | | |0 = OPA clock Disabled. * | | |1 = OPA clock Enabled. * |[31] |PSIOCKEN |PSIO Clock Enable Bit * | | |0 = PSIO clock Disabled. * | | |1 = PSIO clock Enabled. * @var CLK_T::CLKSEL0 * Offset: 0x10 Clock Source Select Control Register 0 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[2:0] |HCLKSEL |HCLK Clock Source Selection (Write Protect) * | | |Before clock switching, the related clock sources (both pre-select and new-select) must be turned on. * | | |The default value is reloaded from the value of CFOSC (CONFIG0[26]) in user configuration register of Flash controller by any reset * | | |Therefore the default value is either 000b or 101b. * | | |000 = Clock source from HXT. * | | |001 = Clock source from LXT. * | | |010 = Clock source from PLL. * | | |011 = Clock source from LIRC. * | | |101= Clock source from MIRC. * | | |111= Clock source from HIRC. * | | |Other = Reserved. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[5:3] |STCLKSEL |Cortex-M23 SysTick Clock Source Selection (Write Protect) * | | |If SYST_CTRL[2]=0, SysTick uses listed clock source below. * | | |000 = Clock source from HXT. * | | |001 = Clock source from LXT. * | | |010 = Clock source from HXT/2. * | | |011 = Clock source from HCLK/2. * | | |111 = Clock source from HIRC/2. * | | |Note: if SysTick clock source is not from HCLK (i.e * | | |SYST_CTRL[2] = 0), SysTick clock source must less than or equal to HCLK/2. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[8] |USBDSEL |USB Device Clock Source Selection (Write Protect) * | | |These bits are protected bit * | | |It means programming this bit needs to write "59h", "16h", "88h" to address 0x4000_0100 to disable register protection * | | |Refer to the register REGWRPROT at address GCR_BA+0x100. * | | |0 = Clock source from HIRC. * | | |1 = Clock source from PLL. divided * @var CLK_T::CLKSEL1 * Offset: 0x14 Clock Source Select Control Register 1 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[1:0] |WDTSEL |Watchdog Timer Clock Source Selection (Write Protect) * | | |00 = Reserved. * | | |01 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT). * | | |10 = Clock source from HCLK/2048. * | | |11 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC). * | | |Note: This bit is write protected.Refer to the SYS_REGLCTL register * | | |Note: This bit is forced to 11 when CONFIG0[31], CONFIG0[4], CONFIG0[3] are all ones. * |[3:2] |WWDTSEL |Window Watchdog Timer Clock Source Selection (Write Protect) * | | |10 = Clock source from HCLK/2048. * | | |11 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC). * | | |Others = Reserved. * |[6:4] |CLKOSEL |Clock Divider Clock Source Selection * | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT). * | | |001 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT). * | | |010 = Clock source from HCLK. * | | |011 = Clock source from 48 MHz internal high speed RC oscillator (HIRC). * | | |100 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC). * | | |101 = Clock source from 4 MHz internal medium speed RC oscillator (MIRC). * | | |110 = Clock source from PLL. * | | |111 = Clock source from internal USB synchronous mode. * |[10:8] |TMR0SEL |TIMER0 Clock Source Selection * | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT). * | | |001 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT). * | | |010 = Clock source from PCLK0. * | | |011 = Clock source from external clock T0 pin. * | | |101 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC). * | | |111 = Clock source from 48 MHz internal high speed RC oscillator (HIRC). * | | |Others = Reserved. * |[14:12] |TMR1SEL |TIMER1 Clock Source Selection * | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT). * | | |001 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT). * | | |010 = Clock source from PCLK0. * | | |011 = Clock source from external clock T1 pin. * | | |101 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC). * | | |111 = Clock source from 48 MHz internal high speed RC oscillator (HIRC). * | | |Others = Reserved. * |[18:16] |TMR2SEL |TIMER2 Clock Source Selection * | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT). * | | |001 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT). * | | |010 = Clock source from PCLK1. * | | |011 = Clock source from external clock T2 pin. * | | |101 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC). * | | |111 = Clock source from 48 MHz internal high speed RC oscillator (HIRC). * | | |Others = Reserved. * |[22:20] |TMR3SEL |TIMER3 Clock Source Selection * | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT). * | | |001 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT). * | | |010 = Clock source from PCLK1. * | | |011 = Clock source from external clock T3 pin. * | | |101 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC). * | | |111 = Clock source from 48 MHz internal high speed RC oscillator (HIRC). * | | |Others = Reserved. * |[26:24] |UART0SEL |UART0 Clock Source Selection * | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT). * | | |001 = Clock source from PLL. * | | |010 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT). * | | |011 = Clock source from 48 MHz internal high speed RC oscillator (HIRC). * | | |100= PCLK0-> default. * | | |101= LIRC * |[30:28] |UART1SEL |UART1 Clock Source Selection * | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT). * | | |001 = Clock source from PLL. * | | |010 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT). * | | |011 = Clock source from 48 MHz internal high speed RC oscillator (HIRC). * | | |100= PCLK1 -> default. * | | |101= LIRC * @var CLK_T::CLKSEL2 * Offset: 0x18 Clock Source Select Control Register 2 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |PWM0SEL |PWM0 Clock Source Selection * | | |The peripheral clock source of PWM0 is defined by PWM0SEL. * | | |0 = Clock source from PLL. * | | |1 = Clock source from PCLK0. * |[1] |PWM1SEL |PWM1 Clock Source Selection * | | |The peripheral clock source of PWM1 is defined by PWM1SEL. * | | |0 = Clock source from PLL. * | | |1 = Clock source from PCLK1. * |[3:2] |QSPI0SEL |QSPI0 Clock Source Selection * | | |00 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT). * | | |01 = Clock source from PLL. * | | |10 = Clock source from PCLK0. * | | |11 = Clock source from 48 MHz internal high speed RC oscillator (HIRC). * |[5:4] |SPI0SEL |SPI0 Clock Source Selection * | | |00 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT). * | | |01 = Clock source from PLL. * | | |10 = Clock source from PCLK1. * | | |11 = Clock source from 48 MHz internal high speed RC oscillator (HIRC). * |[8] |BPWM0SEL |BPWM0 Clock Source Selection * | | |The peripheral clock source of BPWM0 is defined by BPWM0SEL. * | | |0 = Clock source from PLL. * | | |1 = Clock source from PCLK0. * |[9] |BPWM1SEL |BPWM1 Clock Source Selection * | | |The peripheral clock source of BPWM1 is defined by BPWM1SEL. * | | |0 = Clock source from PLL. * | | |1 = Clock source from PCLK1. * |[30:28] |PSIOSEL |PSIO Clock Source Selection * | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT). * | | |001 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT). * | | |010 = Clock source from PCLK1. * | | |011 = Clock source from PLL. * | | |100 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC). * | | |111 = Clock source from 48 MHz internal high speed RC oscillator (HIRC). * | | |Others = Reserved. * @var CLK_T::CLKSEL3 * Offset: 0x1C Clock Source Select Control Register 3 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[1:0] |SC0SEL |SC0 Clock Source Selection * | | |00 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT). * | | |01 = Clock source from PLL. * | | |10 = Clock source from PCLK0. * | | |11 = Clock source from 48 MHz internal high speed RC oscillator (HIRC). * |[26:24] |UART2SEL |UART2 Clock Source Selection * | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT). * | | |001 = Clock source from PLL. * | | |010 = Reserved. * | | |010 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT). * | | |011 = Clock source from 48 MHz internal high speed RC oscillator (HIRC). * | | |100= PCLK 0-> default. * | | |101= LIRC * @var CLK_T::CLKDIV0 * Offset: 0x20 Clock Divider Number Register 0 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[3:0] |HCLKDIV |HCLK Clock Divide Number From HCLK Clock Source * | | |HCLK clock frequency = (HCLK clock source frequency) / (HCLKDIV + 1). * |[7:4] |USBDIV |USB Clock Divide Number From PLL Clock * | | |USB clock frequency = (PLL frequency) / (USBDIV + 1). * |[11:8] |UART0DIV |UART0 Clock Divide Number From UART0 Clock Source * | | |UART0 clock frequency = (UART0 clock source frequency) / (UART0DIV + 1). * |[15:12] |UART1DIV |UART1 Clock Divide Number From UART1 Clock Source * | | |UART1 clock frequency = (UART1 clock source frequency) / (UART1DIV + 1). * |[23:16] |EADCDIV |EADC Clock Divide Number From EADC Clock Source * | | |EADC clock frequency = (EADC clock source frequency) / (EADCDIV + 1). * @var CLK_T::CLKDIV1 * Offset: 0x24 Clock Divider Number Register 1 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[7:0] |SC0DIV |SC0 Clock Divide Number From SC0 Clock Source * | | |SC0 clock frequency = (SC0 clock source frequency ) / (SC0DIV + 1). * |[31:24] |PSIODIV |PSIO Clock Divide Number From PSIO Clock Source * | | |PSIO clock frequency = (PSIO clock source frequency ) / (PSIODIV + 1). * @var CLK_T::CLKDIV4 * Offset: 0x30 Clock Divider Number Register 4 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[3:0] |UART2DIV |UART2 Clock Divide Number From UART2 Clock Source * | | |UART2 clock frequency = (UART2 clock source frequency) / (UART2DIV + 1). * @var CLK_T::PCLKDIV * Offset: 0x34 APB Clock Divider Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[2:0] |APB0DIV |APB0 Clock DIvider * | | |APB0 clock can be divided from HCLK * | | |000: PCLK0 = HCLK. * | | |001: PCLK0 = 1/2 HCLK. * | | |010: PCLK0 = 1/4 HCLK. * | | |011: PCLK0 = 1/8 HCLK. * | | |100: PCLK0 = 1/16 HCLK. * | | |101: PCLK0 = 1/32 HCLK. * | | |Others: Reserved. * |[6:4] |APB1DIV |APB1 Clock DIvider * | | |APB1 clock can be divided from HCLK * | | |000: PCLK1 = HCLK. * | | |001: PCLK1 = 1/2 HCLK. * | | |010: PCLK1 = 1/4 HCLK. * | | |011: PCLK1 = 1/8 HCLK. * | | |100: PCLK1 = 1/16 HCLK. * | | |101: PCLK1 = 1/32 HCLK. * | | |Others: Reserved. * @var CLK_T::PLLCTL * Offset: 0x40 PLL Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[5:0] |FBDIV |PLL Feedback Divider Control (Write Protect) * | | |Refer to the formulas below the table. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[12:9] |INDIV |PLL Input Divider Control (Write Protect) * | | |Refer to the formulas below the table. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[15:14] |OUTDIV |PLL Output Divider Control (Write Protect) * | | |Refer to the formulas below the table. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[16] |PD |Power-down Mode (Write Protect) * | | |If set the PDEN bit to 1 in CLK_PWRCTL register, the PLL will enter Power-down mode, too. * | | |0 = PLL is in normal mode. * | | |1 = PLL is in Power-down mode (default). * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[17] |BP |PLL Bypass Control (Write Protect) * | | |0 = PLL is in normal mode (default). * | | |1 = PLL clock output is same as PLL input clock FIN. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[18] |OE |PLL OE (FOUT Enable) Pin Control (Write Protect) * | | |0 = PLL FOUT Enabled. * | | |1 = PLL FOUT is fixed low. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[20:19] |PLLSRC |PLL Source Clock Selection (Write Protect) * | | |00 = PLL source clock from 4~32 MHz external high-speed crystal oscillator (HXT). * | | |01 = PLL source clock from 12 MHz internal high-speed oscillator (HIRC/4). * | | |10 = PLL source clock from 4~32 MHz external high-speed crystal oscillator (HXT). * | | |11 = PLL source clock from 4 MHz internal high-speed oscillator (MIRC). * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * | | |Note: MIRC and HIRC have to be both on when source switch between them * |[23] |STBSEL |PLL Stable Counter Selection (Write Protect) * | | |0 = PLL stable time is 1200 PLL source clock (suitable for source clock is equal to or less than 12 MHz). * | | |1 = PLL stable time is 2400 PLL source clock (suitable for source clock is larger than 12 MHz). * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[24] |PLL_CLF_EN|1: PLL Clock Filter On * | | |0 : OFF * @var CLK_T::STATUS * Offset: 0x50 Clock Status Monitor Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |HXTSTB |HXT Clock Source Stable Flag (Read Only) * | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock is not stable or disabled. * | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock is stable and enabled. * |[1] |LXTSTB |LXT Clock Source Stable Flag (Read Only) * | | |0 = 32.768 kHz external low speed crystal oscillator (LXT) clock is not stable or disabled. * | | |1 = 32.768 kHz external low speed crystal oscillator (LXT) clock is stabled and enabled. * |[2] |PLLSTB |Internal PLL Clock Source Stable Flag (Read Only) * | | |0 = Internal PLL clock is not stable or disabled. * | | |1 = Internal PLL clock is stable and enabled. * |[3] |LIRCSTB |LIRC Clock Source Stable Flag (Read Only) * | | |0 = 38.4 kHz internal low speed RC oscillator (LIRC) clock is not stable or disabled. * | | |1 = 38.4 kHz internal low speed RC oscillator (LIRC) clock is stable and enabled. * |[4] |HIRCSTB |HIRC Clock Source Stable Flag (Read Only) * | | |0 = 48 MHz internal high speed RC oscillator (HIRC) clock is not stable or disabled. * | | |1 = 48 MHz internal high speed RC oscillator (HIRC) clock is stable and enabled. * |[6] |MIRCSTB |MIRC Clock Source Stable Flag (Read Only) * | | |0 = 4 MHz internal mid speed RC oscillator (MIRC) clock is not stable or disabled. * | | |1 = 4 MHz internal mid speed RC oscillator (MIRC) clock is stable and enabled. * |[7] |CLKSFAIL |Clock Switching Fail Flag (Read Only) * | | |This bit is updated when software switches system clock source * | | |If switch target clock is stable, this bit will be set to 0 * | | |If switch target clock is not stable, this bit will be set to 1. * | | |0 = Clock switching success. * | | |1 = Clock switching failure. * | | |Note: Write 1 to clear the bit to 0. * @var CLK_T::CLKOCTL * Offset: 0x60 Clock Output Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[3:0] |FREQSEL |Clock Output Frequency Selection * | | |The formula of output frequency is * | | |Fout = Fin/2(N+1). * | | |Fin is the input clock frequency. * | | |Fout is the frequency of divider output clock. * | | |N is the 4-bit value of FREQSEL[3:0]. * |[4] |CLKOEN |Clock Output Enable Bit * | | |0 = Clock Output function Disabled. * | | |1 = Clock Output function Enabled. * |[5] |DIV1EN |Clock Output Divide One Enable Bit * | | |0 = Clock Output will output clock with source frequency divided by FREQSEL. * | | |1 = Clock Output will output clock with source frequency. * |[6] |CLK1HZEN |Clock Output 1Hz Enable Bit * | | |0 = 1 Hz clock output for 32.768 kHz frequency compensation Disabled. * | | |1 = 1 Hz clock output for 32.768 kHz frequency compensation Enabled. * @var CLK_T::CLKDCTL * Offset: 0x70 Clock Fail Detector Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[4] |HXTFDEN |HXT Clock Fail Detector Enable Bit * | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock fail detector Disabled. * | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock fail detector Enabled. * |[5] |HXTFIEN |HXT Clock Fail Interrupt Enable Bit * | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock fail interrupt Disabled. * | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock fail interrupt Enabled. * |[12] |LXTFDEN |LXT Clock Fail Detector Enable Bit * | | |0 = 32.768 kHz external low speed crystal oscillator (LXT) clock fail detector Disabled. * | | |1 = 32.768 kHz external low speed crystal oscillator (LXT) clock fail detector Enabled. * |[13] |LXTFIEN |LXT Clock Fail Interrupt Enable Bit * | | |0 = 32.768 kHz external low speed crystal oscillator (LXT) clock fail interrupt Disabled. * | | |1 = 32.768 kHz external low speed crystal oscillator (LXT) clock fail interrupt Enabled. * |[16] |HXTFQDEN |HXT Clock Frequency Range Detector Enable Bit * | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock frequency range detector Disabled. * | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock frequency range detector Enabled. * |[17] |HXTFQIEN |HXT Clock Frequency Range Detector Interrupt Enable Bit * | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock frequency range detector fail interrupt Disabled. * | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock frequency range detector fail interrupt Enabled. * @var CLK_T::CLKDSTS * Offset: 0x74 Clock Fail Detector Status Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |HXTFIF |HXT Clock Fail Interrupt Flag (Write Protect) * | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock is normal. * | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock stops. * | | |Note: Write 1 to clear the bit to 0. * |[1] |LXTFIF |LXT Clock Fail Interrupt Flag (Write Protect) * | | |0 = 32.768 kHz external low speed crystal oscillator (LXT) clock is normal. * | | |1 = 32.768 kHz external low speed crystal oscillator (LXT) stops. * | | |Note: Write 1 to clear the bit to 0. * |[8] |HXTFQIF |HXT Clock Frequency Range Detector Interrupt Flag (Write Protect) * | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock frequency is normal. * | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock frequency is abnormal. * | | |Note: Write 1 to clear the bit to 0. * @var CLK_T::CDUPB * Offset: 0x78 Clock Frequency Range Detector Upper Boundary Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[9:0] |UPERBD |HXT Clock Frequency Range Detector Upper Boundary Value * | | |The bits define the maximum value of frequency range detector window. * | | |When HXT frequency higher than this maximum frequency value, the HXT Clock Frequency Range Detector Interrupt Flag will set to 1. * @var CLK_T::CDLOWB * Offset: 0x7C Clock Frequency Range Detector Lower Boundary Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[9:0] |LOWERBD |HXT Clock Frequency Range Detector Lower Boundary Value * | | |The bits define the minimum value of frequency range detector window. * | | |When HXT frequency lower than this minimum frequency value, the HXT Clock Frequency Range Detector Interrupt Flag will set to 1. * @var CLK_T::PMUCTL * Offset: 0x90 Power Manager Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[2:0] |PDMSEL |Power-down Mode Selection (Write Protect) * | | |This is a protected register. Please refer to open lock sequence to program it. * | | |These bits control chip power-down mode grade selection when CPU execute WFI/WFE instruction. * | | |000 = Power-down mode is selected. (PD) * | | |010 = fast wake up.(FWPD) * | | |110 = Deep Power-down mode is selected (DPD). * | | |others = Reserved. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[8] |WKTMREN |Wake-up Timer Enable (Write Protect) * | | |This is a protected register. Please refer to open lock sequence to program it. * | | |0 = Wake-up timer disable at DPD mode. * | | |1 = Wake-up timer enabled at DPD mode. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[11:9] |WKTMRIS |Wake-up Timer Time-out Interval Select (Write Protect) * | | |This is a protected register. Please refer to open lock sequence to program it. * | | |These bits control wake-up timer time-out interval when chip at DPD mode. * | | |000 = Time-out interval is 128 OSC32K clocks (~3.368 ms). * | | |001 = Time-out interval is 256 OSC32K clocks (~6.736 ms). * | | |010 = Time-out interval is 512 OSC32K clocks (~13.47 ms). * | | |011 = Time-out interval is 1024 OSC32K clocks (~26.95 ms). * | | |100 = Time-out interval is 4096 OSC32K clocks (~107.79 ms). * | | |101 = Time-out interval is 8192 OSC32K clocks (~215.58 ms). * | | |110 = Time-out interval is 16384 OSC32K clocks (~431.16 ms). * | | |111 = Time-out interval is 32768 OSC32K clocks (~862.32 ms). * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[17:16] |WKPINEN0 |Wake-up Pin Enable 0(Write Protect) * | | |This is a protected register. Please refer to open lock sequence to program it. * | | |This is control register for GPC.0 to wake-up pin. * | | |00 = Wake-up pin disable at Deep Power-down mode. * | | |01 = Wake-up pin rising edge enabled at Deep Power-down mode. * | | |10 = Wake-up pin falling edge enabled at Deep Power-down mode. * | | |11 = Wake-up pin both edge enabled at Deep Power-down mode. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[22] |WKPINDBEN |Wake-up pin De-bounce Enable Bit (Write Protect) * | | |The WKPINDBEN bit is used to enable the de-bounce function for wake-up pin. * | | |If the input signal pulse width cannot be sampled by continuous eight de-bounce sample cycle, * | | |the input signal transition is seen as the signal bounce and will not trigger the wakeup. * | | |The de-bounce clock source is the 38 kHz internal low speed RC oscillator (LIRC). * | | |0 = Deep power-down wake-up pin De-bounce function disable. * | | |1 = Deep power-down wake-up pin De-bounce function enable. * | | |The de-bounce function is valid only for edge triggered * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[23] |RTCWKEN |RTC Wake-up Enable (Write Protect) * | | |This is a protected register. Please refer to open lock sequence to program it. * | | |0 = RTC wake-up disable at Deep Power-down mode or Standby Power-down mode. * | | |1 = RTC wake-up enabled at Deep Power-down mode or Standby Power-down mode. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[25:24] |WKPINEN1 |Wake-up Pin Enable 1(Write Protect) * | | |This is a protected register. Please refer to open lock sequence to program it. * | | |This is control register for GPB.0 to wake-up pin. * | | |00 = Wake-up pin disable at Deep Power-down mode. * | | |01 = Wake-up pin rising edge enabled at Deep Power-down mode. * | | |10 = Wake-up pin falling edge enabled at Deep Power-down mode. * | | |11 = Wake-up pin both edge enabled at Deep Power-down mode. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register * |[27:26] |WKPINEN2 |Wake-up Pin Enable 2(Write Protect) * | | |This is a protected register. Please refer to open lock sequence to program it. * | | |This is control register for GPB.2 to wake-up pin. * | | |00 = Wake-up pin disable at Deep Power-down mode. * | | |01 = Wake-up pin rising edge enabled at Deep Power-down mode. * | | |10 = Wake-up pin falling edge enabled at Deep Power-down mode. * | | |11 = Wake-up pin both edge enabled at Deep Power-down mode. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[29:28] |WKPINEN3 |Wake-up Pin Enable 3(Write Protect) * | | |This is a protected register. Please refer to open lock sequence to program it. * | | |This is control register for GPB.12 to wake-up pin. * | | |00 = Wake-up pin disable at Deep Power-down mode. * | | |01 = Wake-up pin rising edge enabled at Deep Power-down mode. * | | |10 = Wake-up pin falling edge enabled at Deep Power-down mode. * | | |11 = Wake-up pin both edge enabled at Deep Power-down mode. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * |[31:30] |WKPINEN4 |Wake-up Pin Enable 4(Write Protect) * | | |This is a protected register. Please refer to open lock sequence to program it. * | | |This is control register for GPF.6 to wake-up pin. * | | |00 = Wake-up pin disable at Deep Power-down mode. * | | |01 = Wake-up pin rising edge enabled at Deep Power-down mode. * | | |10 = Wake-up pin falling edge enabled at Deep Power-down mode. * | | |11 = Wake-up pin both edge enabled at Deep Power-down mode. * | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register. * @var CLK_T::PMUSTS * Offset: 0x94 Power Manager Status Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |PINWK0 |Pin Wake-up Flag (Read Only) * | | |This flag indicates that wake-up of chip from Deep Power-down mode was requested by a transition of the WAKEUP pin (GPC.0) * | | |This flag is cleared when DPD mode is entered. * |[1] |TMRWK |Timer Wake-up Flag (Read Only) * | | |This flag indicates that wake-up of chip from Deep Power-down mode (DPD) was requested by wakeup timer time-out * | | |This flag is cleared when DPD mode is entered. * |[2] |RTCWK |RTC Wake-up Flag (Read Only) * | | |This flag indicates that wakeup of device from Deep Power-down mode (DPD) was requested with a RTC alarm, tick time or tamper happened * | | |This flag is cleared when DPD mode is entered. * |[3] |PINWK1 |Pin Wake-up Flag (Read Only) * | | |This flag indicates that wake-up of chip from Deep Power-down mode was requested by a transition of the WAKEUP pin (GPB.0) * | | |This flag is cleared when DPD mode is entered. * |[4] |PINWK2 |Pin Wake-up Flag (Read Only) * | | |This flag indicates that wake-up of chip from Deep Power-down mode was requested by a transition of the WAKEUP pin (GPB.2) * | | |This flag is cleared when DPD mode is entered. * |[5] |PINWK3 |Pin Wake-up Flag (Read Only) * | | |This flag indicates that wake-up of chip from Deep Power-down mode was requested by a transition of the WAKEUP pin (GPB.12) * | | |This flag is cleared when DPD mode is entered. * |[6] |PINWK4 |Pin Wake-up Flag (Read Only) * | | |This flag indicates that wake-up of chip from Deep Power-down mode was requested by a transition of the WAKEUP pin (GPF.6) * | | |This flag is cleared when DPD mode is entered. * |[12] |LVRWK |LVR Wake-up Flag (Read Only) * | | |This flag indicates that wakeup of device from Deep Power-down mode was requested with a LVR happened * | | |This flag is cleared when DPD mode is entered. * |[31] |CLRWK |Clear Wake-up Flag * | | |0 = No clear. * | | |1= Clear all wake-up flag. * @var CLK_T::HXTFSEL * Offset: 0xB4 HXT Filter Select Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |HXTFSEL |HXT Filter Select (Write Protect) * | | |0 = HXT frequency is > 12MHz. * | | |1 = HXT frequency is <= 12MHz. */ __IO uint32_t PWRCTL; /*!< [0x0000] System Power-down Control Register */ __IO uint32_t AHBCLK; /*!< [0x0004] AHB Devices Clock Enable Control Register */ __IO uint32_t APBCLK0; /*!< [0x0008] APB Devices Clock Enable Control Register 0 */ __IO uint32_t APBCLK1; /*!< [0x000c] APB Devices Clock Enable Control Register 1 */ __IO uint32_t CLKSEL0; /*!< [0x0010] Clock Source Select Control Register 0 */ __IO uint32_t CLKSEL1; /*!< [0x0014] Clock Source Select Control Register 1 */ __IO uint32_t CLKSEL2; /*!< [0x0018] Clock Source Select Control Register 2 */ __IO uint32_t CLKSEL3; /*!< [0x001c] Clock Source Select Control Register 3 */ __IO uint32_t CLKDIV0; /*!< [0x0020] Clock Divider Number Register 0 */ __IO uint32_t CLKDIV1; /*!< [0x0024] Clock Divider Number Register 1 */ /// @cond HIDDEN_SYMBOLS __I uint32_t RESERVE0[2]; /// @endcond //HIDDEN_SYMBOLS __IO uint32_t CLKDIV4; /*!< [0x0030] Clock Divider Number Register 4 */ __IO uint32_t PCLKDIV; /*!< [0x0034] APB Clock Divider Register */ /// @cond HIDDEN_SYMBOLS __I uint32_t RESERVE1[2]; /// @endcond //HIDDEN_SYMBOLS __IO uint32_t PLLCTL; /*!< [0x0040] PLL Control Register */ /// @cond HIDDEN_SYMBOLS __I uint32_t RESERVE2[3]; /// @endcond //HIDDEN_SYMBOLS __I uint32_t STATUS; /*!< [0x0050] Clock Status Monitor Register */ /// @cond HIDDEN_SYMBOLS __I uint32_t RESERVE3[3]; /// @endcond //HIDDEN_SYMBOLS __IO uint32_t CLKOCTL; /*!< [0x0060] Clock Output Control Register */ /// @cond HIDDEN_SYMBOLS __I uint32_t RESERVE4[3]; /// @endcond //HIDDEN_SYMBOLS __IO uint32_t CLKDCTL; /*!< [0x0070] Clock Fail Detector Control Register */ __IO uint32_t CLKDSTS; /*!< [0x0074] Clock Fail Detector Status Register */ __IO uint32_t CDUPB; /*!< [0x0078] Clock Frequency Range Detector Upper Boundary Register */ __IO uint32_t CDLOWB; /*!< [0x007c] Clock Frequency Range Detector Lower Boundary Register */ /// @cond HIDDEN_SYMBOLS __I uint32_t RESERVE5[4]; /// @endcond //HIDDEN_SYMBOLS __IO uint32_t PMUCTL; /*!< [0x0090] Power Manager Control Register */ __IO uint32_t PMUSTS; /*!< [0x0094] Power Manager Status Register */ /// @cond HIDDEN_SYMBOLS __I uint32_t RESERVE6[7]; /// @endcond //HIDDEN_SYMBOLS __IO uint32_t HXTFSEL; /*!< [0x00b4] HXT Filter Select Control Register */ } CLK_T; /** @addtogroup CLK_CONST CLK Bit Field Definition Constant Definitions for CLK Controller @{ */ #define CLK_PWRCTL_HXTEN_Pos (0) /*!< CLK_T::PWRCTL: HXTEN Position */ #define CLK_PWRCTL_HXTEN_Msk (0x1ul << CLK_PWRCTL_HXTEN_Pos) /*!< CLK_T::PWRCTL: HXTEN Mask */ #define CLK_PWRCTL_LXTEN_Pos (1) /*!< CLK_T::PWRCTL: LXTEN Position */ #define CLK_PWRCTL_LXTEN_Msk (0x1ul << CLK_PWRCTL_LXTEN_Pos) /*!< CLK_T::PWRCTL: LXTEN Mask */ #define CLK_PWRCTL_HIRCEN_Pos (2) /*!< CLK_T::PWRCTL: HIRCEN Position */ #define CLK_PWRCTL_HIRCEN_Msk (0x1ul << CLK_PWRCTL_HIRCEN_Pos) /*!< CLK_T::PWRCTL: HIRCEN Mask */ #define CLK_PWRCTL_LIRCEN_Pos (3) /*!< CLK_T::PWRCTL: LIRCEN Position */ #define CLK_PWRCTL_LIRCEN_Msk (0x1ul << CLK_PWRCTL_LIRCEN_Pos) /*!< CLK_T::PWRCTL: LIRCEN Mask */ #define CLK_PWRCTL_PDWKDLY_Pos (4) /*!< CLK_T::PWRCTL: PDWKDLY Position */ #define CLK_PWRCTL_PDWKDLY_Msk (0x1ul << CLK_PWRCTL_PDWKDLY_Pos) /*!< CLK_T::PWRCTL: PDWKDLY Mask */ #define CLK_PWRCTL_PDWKIEN_Pos (5) /*!< CLK_T::PWRCTL: PDWKIEN Position */ #define CLK_PWRCTL_PDWKIEN_Msk (0x1ul << CLK_PWRCTL_PDWKIEN_Pos) /*!< CLK_T::PWRCTL: PDWKIEN Mask */ #define CLK_PWRCTL_PDWKIF_Pos (6) /*!< CLK_T::PWRCTL: PDWKIF Position */ #define CLK_PWRCTL_PDWKIF_Msk (0x1ul << CLK_PWRCTL_PDWKIF_Pos) /*!< CLK_T::PWRCTL: PDWKIF Mask */ #define CLK_PWRCTL_PDEN_Pos (7) /*!< CLK_T::PWRCTL: PDEN Position */ #define CLK_PWRCTL_PDEN_Msk (0x1ul << CLK_PWRCTL_PDEN_Pos) /*!< CLK_T::PWRCTL: PDEN Mask */ #define CLK_PWRCTL_MIRCEN_Pos (19) /*!< CLK_T::PWRCTL: MIRCEN Position */ #define CLK_PWRCTL_MIRCEN_Msk (0x1ul << CLK_PWRCTL_MIRCEN_Pos) /*!< CLK_T::PWRCTL: MIRCEN Mask */ #define CLK_PWRCTL_HXTGAIN_Pos (20) /*!< CLK_T::PWRCTL: HXTGAIN Position */ #define CLK_PWRCTL_HXTGAIN_Msk (0x7ul << CLK_PWRCTL_HXTGAIN_Pos) /*!< CLK_T::PWRCTL: HXTGAIN Mask */ #define CLK_AHBCLK_PDMACKEN_Pos (1) /*!< CLK_T::AHBCLK: PDMACKEN Position */ #define CLK_AHBCLK_PDMACKEN_Msk (0x1ul << CLK_AHBCLK_PDMACKEN_Pos) /*!< CLK_T::AHBCLK: PDMACKEN Mask */ #define CLK_AHBCLK_ISPCKEN_Pos (2) /*!< CLK_T::AHBCLK: ISPCKEN Position */ #define CLK_AHBCLK_ISPCKEN_Msk (0x1ul << CLK_AHBCLK_ISPCKEN_Pos) /*!< CLK_T::AHBCLK: ISPCKEN Mask */ #define CLK_AHBCLK_EBICKEN_Pos (3) /*!< CLK_T::AHBCLK: EBICKEN Position */ #define CLK_AHBCLK_EBICKEN_Msk (0x1ul << CLK_AHBCLK_EBICKEN_Pos) /*!< CLK_T::AHBCLK: EBICKEN Mask */ #define CLK_AHBCLK_EXSTCKEN_Pos (4) /*!< CLK_T::AHBCLK: EXSTCKEN Position */ #define CLK_AHBCLK_EXSTCKEN_Msk (0x1ul << CLK_AHBCLK_EXSTCKEN_Pos) /*!< CLK_T::AHBCLK: EXSTCKEN Mask */ #define CLK_AHBCLK_CRCCKEN_Pos (7) /*!< CLK_T::AHBCLK: CRCCKEN Position */ #define CLK_AHBCLK_CRCCKEN_Msk (0x1ul << CLK_AHBCLK_CRCCKEN_Pos) /*!< CLK_T::AHBCLK: CRCCKEN Mask */ #define CLK_AHBCLK_CRPTCKEN_Pos (12) /*!< CLK_T::AHBCLK: CRPTCKEN Position */ #define CLK_AHBCLK_CRPTCKEN_Msk (0x1ul << CLK_AHBCLK_CRPTCKEN_Pos) /*!< CLK_T::AHBCLK: CRPTCKEN Mask */ #define CLK_AHBCLK_FMCIDLE_Pos (15) /*!< CLK_T::AHBCLK: FMCIDLE Position */ #define CLK_AHBCLK_FMCIDLE_Msk (0x1ul << CLK_AHBCLK_FMCIDLE_Pos) /*!< CLK_T::AHBCLK: FMCIDLE Mask */ #define CLK_AHBCLK_GPACKEN_Pos (24) /*!< CLK_T::AHBCLK: GPACKEN Position */ #define CLK_AHBCLK_GPACKEN_Msk (0x1ul << CLK_AHBCLK_GPACKEN_Pos) /*!< CLK_T::AHBCLK: GPACKEN Mask */ #define CLK_AHBCLK_GPBCKEN_Pos (25) /*!< CLK_T::AHBCLK: GPBCKEN Position */ #define CLK_AHBCLK_GPBCKEN_Msk (0x1ul << CLK_AHBCLK_GPBCKEN_Pos) /*!< CLK_T::AHBCLK: GPBCKEN Mask */ #define CLK_AHBCLK_GPCCKEN_Pos (26) /*!< CLK_T::AHBCLK: GPCCKEN Position */ #define CLK_AHBCLK_GPCCKEN_Msk (0x1ul << CLK_AHBCLK_GPCCKEN_Pos) /*!< CLK_T::AHBCLK: GPCCKEN Mask */ #define CLK_AHBCLK_GPDCKEN_Pos (27) /*!< CLK_T::AHBCLK: GPDCKEN Position */ #define CLK_AHBCLK_GPDCKEN_Msk (0x1ul << CLK_AHBCLK_GPDCKEN_Pos) /*!< CLK_T::AHBCLK: GPDCKEN Mask */ #define CLK_AHBCLK_GPECKEN_Pos (28) /*!< CLK_T::AHBCLK: GPECKEN Position */ #define CLK_AHBCLK_GPECKEN_Msk (0x1ul << CLK_AHBCLK_GPECKEN_Pos) /*!< CLK_T::AHBCLK: GPECKEN Mask */ #define CLK_AHBCLK_GPFCKEN_Pos (29) /*!< CLK_T::AHBCLK: GPFCKEN Position */ #define CLK_AHBCLK_GPFCKEN_Msk (0x1ul << CLK_AHBCLK_GPFCKEN_Pos) /*!< CLK_T::AHBCLK: GPFCKEN Mask */ #define CLK_APBCLK0_WDTCKEN_Pos (0) /*!< CLK_T::APBCLK0: WDTCKEN Position */ #define CLK_APBCLK0_WDTCKEN_Msk (0x1ul << CLK_APBCLK0_WDTCKEN_Pos) /*!< CLK_T::APBCLK0: WDTCKEN Mask */ #define CLK_APBCLK0_RTCCKEN_Pos (1) /*!< CLK_T::APBCLK0: RTCCKEN Position */ #define CLK_APBCLK0_RTCCKEN_Msk (0x1ul << CLK_APBCLK0_RTCCKEN_Pos) /*!< CLK_T::APBCLK0: RTCCKEN Mask */ #define CLK_APBCLK0_TMR0CKEN_Pos (2) /*!< CLK_T::APBCLK0: TMR0CKEN Position */ #define CLK_APBCLK0_TMR0CKEN_Msk (0x1ul << CLK_APBCLK0_TMR0CKEN_Pos) /*!< CLK_T::APBCLK0: TMR0CKEN Mask */ #define CLK_APBCLK0_TMR1CKEN_Pos (3) /*!< CLK_T::APBCLK0: TMR1CKEN Position */ #define CLK_APBCLK0_TMR1CKEN_Msk (0x1ul << CLK_APBCLK0_TMR1CKEN_Pos) /*!< CLK_T::APBCLK0: TMR1CKEN Mask */ #define CLK_APBCLK0_TMR2CKEN_Pos (4) /*!< CLK_T::APBCLK0: TMR2CKEN Position */ #define CLK_APBCLK0_TMR2CKEN_Msk (0x1ul << CLK_APBCLK0_TMR2CKEN_Pos) /*!< CLK_T::APBCLK0: TMR2CKEN Mask */ #define CLK_APBCLK0_TMR3CKEN_Pos (5) /*!< CLK_T::APBCLK0: TMR3CKEN Position */ #define CLK_APBCLK0_TMR3CKEN_Msk (0x1ul << CLK_APBCLK0_TMR3CKEN_Pos) /*!< CLK_T::APBCLK0: TMR3CKEN Mask */ #define CLK_APBCLK0_CLKOCKEN_Pos (6) /*!< CLK_T::APBCLK0: CLKOCKEN Position */ #define CLK_APBCLK0_CLKOCKEN_Msk (0x1ul << CLK_APBCLK0_CLKOCKEN_Pos) /*!< CLK_T::APBCLK0: CLKOCKEN Mask */ #define CLK_APBCLK0_ACMP01CKEN_Pos (7) /*!< CLK_T::APBCLK0: ACMP01CKEN Position */ #define CLK_APBCLK0_ACMP01CKEN_Msk (0x1ul << CLK_APBCLK0_ACMP01CKEN_Pos) /*!< CLK_T::APBCLK0: ACMP01CKEN Mask */ #define CLK_APBCLK0_I2C0CKEN_Pos (8) /*!< CLK_T::APBCLK0: I2C0CKEN Position */ #define CLK_APBCLK0_I2C0CKEN_Msk (0x1ul << CLK_APBCLK0_I2C0CKEN_Pos) /*!< CLK_T::APBCLK0: I2C0CKEN Mask */ #define CLK_APBCLK0_I2C1CKEN_Pos (9) /*!< CLK_T::APBCLK0: I2C1CKEN Position */ #define CLK_APBCLK0_I2C1CKEN_Msk (0x1ul << CLK_APBCLK0_I2C1CKEN_Pos) /*!< CLK_T::APBCLK0: I2C1CKEN Mask */ #define CLK_APBCLK0_QSPI0CKEN_Pos (12) /*!< CLK_T::APBCLK0: QSPI0CKEN Position */ #define CLK_APBCLK0_QSPI0CKEN_Msk (0x1ul << CLK_APBCLK0_QSPI0CKEN_Pos) /*!< CLK_T::APBCLK0: QSPI0CKEN Mask */ #define CLK_APBCLK0_SPI0CKEN_Pos (13) /*!< CLK_T::APBCLK0: SPI0CKEN Position */ #define CLK_APBCLK0_SPI0CKEN_Msk (0x1ul << CLK_APBCLK0_SPI0CKEN_Pos) /*!< CLK_T::APBCLK0: SPI0CKEN Mask */ #define CLK_APBCLK0_SPI1CKEN_Pos (14) /*!< CLK_T::APBCLK0: SPI1CKEN Position */ #define CLK_APBCLK0_SPI1CKEN_Msk (0x1ul << CLK_APBCLK0_SPI1CKEN_Pos) /*!< CLK_T::APBCLK0: SPI1CKEN Mask */ #define CLK_APBCLK0_UART0CKEN_Pos (16) /*!< CLK_T::APBCLK0: UART0CKEN Position */ #define CLK_APBCLK0_UART0CKEN_Msk (0x1ul << CLK_APBCLK0_UART0CKEN_Pos) /*!< CLK_T::APBCLK0: UART0CKEN Mask */ #define CLK_APBCLK0_UART1CKEN_Pos (17) /*!< CLK_T::APBCLK0: UART1CKEN Position */ #define CLK_APBCLK0_UART1CKEN_Msk (0x1ul << CLK_APBCLK0_UART1CKEN_Pos) /*!< CLK_T::APBCLK0: UART1CKEN Mask */ #define CLK_APBCLK0_UART2CKEN_Pos (18) /*!< CLK_T::APBCLK0: UART2CKEN Position */ #define CLK_APBCLK0_UART2CKEN_Msk (0x1ul << CLK_APBCLK0_UART2CKEN_Pos) /*!< CLK_T::APBCLK0: UART2CKEN Mask */ #define CLK_APBCLK0_UART3CKEN_Pos (19) /*!< CLK_T::APBCLK0: UART3CKEN Position */ #define CLK_APBCLK0_UART3CKEN_Msk (0x1ul << CLK_APBCLK0_UART3CKEN_Pos) /*!< CLK_T::APBCLK0: UART3CKEN Mask */ #define CLK_APBCLK0_USBDCKEN_Pos (27) /*!< CLK_T::APBCLK0: USBDCKEN Position */ #define CLK_APBCLK0_USBDCKEN_Msk (0x1ul << CLK_APBCLK0_USBDCKEN_Pos) /*!< CLK_T::APBCLK0: USBDCKEN Mask */ #define CLK_APBCLK0_EADCCKEN_Pos (28) /*!< CLK_T::APBCLK0: EADCCKEN Position */ #define CLK_APBCLK0_EADCCKEN_Msk (0x1ul << CLK_APBCLK0_EADCCKEN_Pos) /*!< CLK_T::APBCLK0: EADCCKEN Mask */ #define CLK_APBCLK0_TKCKEN_Pos (29) /*!< CLK_T::APBCLK0: TKCKEN Position */ #define CLK_APBCLK0_TKCKEN_Msk (0x1ul << CLK_APBCLK0_TKCKEN_Pos) /*!< CLK_T::APBCLK0: TKCKEN Mask */ #define CLK_APBCLK1_SC0CKEN_Pos (0) /*!< CLK_T::APBCLK1: SC0CKEN Position */ #define CLK_APBCLK1_SC0CKEN_Msk (0x1ul << CLK_APBCLK1_SC0CKEN_Pos) /*!< CLK_T::APBCLK1: SC0CKEN Mask */ #define CLK_APBCLK1_USCI0CKEN_Pos (8) /*!< CLK_T::APBCLK1: USCI0CKEN Position */ #define CLK_APBCLK1_USCI0CKEN_Msk (0x1ul << CLK_APBCLK1_USCI0CKEN_Pos) /*!< CLK_T::APBCLK1: USCI0CKEN Mask */ #define CLK_APBCLK1_USCI1CKEN_Pos (9) /*!< CLK_T::APBCLK1: USCI1CKEN Position */ #define CLK_APBCLK1_USCI1CKEN_Msk (0x1ul << CLK_APBCLK1_USCI1CKEN_Pos) /*!< CLK_T::APBCLK1: USCI1CKEN Mask */ #define CLK_APBCLK1_USCI2CKEN_Pos (10) /*!< CLK_T::APBCLK1: USCI2CKEN Position */ #define CLK_APBCLK1_USCI2CKEN_Msk (0x1ul << CLK_APBCLK1_USCI2CKEN_Pos) /*!< CLK_T::APBCLK1: USCI2CKEN Mask */ #define CLK_APBCLK1_DACCKEN_Pos (12) /*!< CLK_T::APBCLK1: DACCKEN Position */ #define CLK_APBCLK1_DACCKEN_Msk (0x1ul << CLK_APBCLK1_DACCKEN_Pos) /*!< CLK_T::APBCLK1: DACCKEN Mask */ #define CLK_APBCLK1_LCDCKEN_Pos (14) /*!< CLK_T::APBCLK1: LCDCKEN Position */ #define CLK_APBCLK1_LCDCKEN_Msk (0x1ul << CLK_APBCLK1_LCDCKEN_Pos) /*!< CLK_T::APBCLK1: LCDCKEN Mask */ #define CLK_APBCLK1_LCDCPCKEN_Pos (15) /*!< CLK_T::APBCLK1: LCDCPCKEN Position */ #define CLK_APBCLK1_LCDCPCKEN_Msk (0x1ul << CLK_APBCLK1_LCDCPCKEN_Pos) /*!< CLK_T::APBCLK1: LCDCPCKEN Mask */ #define CLK_APBCLK1_PWM0CKEN_Pos (16) /*!< CLK_T::APBCLK1: PWM0CKEN Position */ #define CLK_APBCLK1_PWM0CKEN_Msk (0x1ul << CLK_APBCLK1_PWM0CKEN_Pos) /*!< CLK_T::APBCLK1: PWM0CKEN Mask */ #define CLK_APBCLK1_PWM1CKEN_Pos (17) /*!< CLK_T::APBCLK1: PWM1CKEN Position */ #define CLK_APBCLK1_PWM1CKEN_Msk (0x1ul << CLK_APBCLK1_PWM1CKEN_Pos) /*!< CLK_T::APBCLK1: PWM1CKEN Mask */ #define CLK_APBCLK1_BPWM0CKEN_Pos (18) /*!< CLK_T::APBCLK1: BPWM0CKEN Position */ #define CLK_APBCLK1_BPWM0CKEN_Msk (0x1ul << CLK_APBCLK1_BPWM0CKEN_Pos) /*!< CLK_T::APBCLK1: BPWM0CKEN Mask */ #define CLK_APBCLK1_BPWM1CKEN_Pos (19) /*!< CLK_T::APBCLK1: BPWM1CKEN Position */ #define CLK_APBCLK1_BPWM1CKEN_Msk (0x1ul << CLK_APBCLK1_BPWM1CKEN_Pos) /*!< CLK_T::APBCLK1: BPWM1CKEN Mask */ #define CLK_APBCLK1_OPACKEN_Pos (30) /*!< CLK_T::APBCLK1: OPACKEN Position */ #define CLK_APBCLK1_OPACKEN_Msk (0x1ul << CLK_APBCLK1_OPACKEN_Pos) /*!< CLK_T::APBCLK1: OPACKEN Mask */ #define CLK_APBCLK1_PSIOCKEN_Pos (31) /*!< CLK_T::APBCLK1: PSIOCKEN Position */ #define CLK_APBCLK1_PSIOCKEN_Msk (0x1ul << CLK_APBCLK1_PSIOCKEN_Pos) /*!< CLK_T::APBCLK1: PSIOCKEN Mask */ #define CLK_CLKSEL0_HCLKSEL_Pos (0) /*!< CLK_T::CLKSEL0: HCLKSEL Position */ #define CLK_CLKSEL0_HCLKSEL_Msk (0x7ul << CLK_CLKSEL0_HCLKSEL_Pos) /*!< CLK_T::CLKSEL0: HCLKSEL Mask */ #define CLK_CLKSEL0_STCLKSEL_Pos (3) /*!< CLK_T::CLKSEL0: STCLKSEL Position */ #define CLK_CLKSEL0_STCLKSEL_Msk (0x7ul << CLK_CLKSEL0_STCLKSEL_Pos) /*!< CLK_T::CLKSEL0: STCLKSEL Mask */ #define CLK_CLKSEL0_USBDSEL_Pos (8) /*!< CLK_T::CLKSEL0: USBDSEL Position */ #define CLK_CLKSEL0_USBDSEL_Msk (0x1ul << CLK_CLKSEL0_USBDSEL_Pos) /*!< CLK_T::CLKSEL0: USBDSEL Mask */ #define CLK_CLKSEL1_WDTSEL_Pos (0) /*!< CLK_T::CLKSEL1: WDTSEL Position */ #define CLK_CLKSEL1_WDTSEL_Msk (0x3ul << CLK_CLKSEL1_WDTSEL_Pos) /*!< CLK_T::CLKSEL1: WDTSEL Mask */ #define CLK_CLKSEL1_WWDTSEL_Pos (2) /*!< CLK_T::CLKSEL1: WWDTSEL Position */ #define CLK_CLKSEL1_WWDTSEL_Msk (0x3ul << CLK_CLKSEL1_WWDTSEL_Pos) /*!< CLK_T::CLKSEL1: WWDTSEL Mask */ #define CLK_CLKSEL1_CLKOSEL_Pos (4) /*!< CLK_T::CLKSEL1: CLKOSEL Position */ #define CLK_CLKSEL1_CLKOSEL_Msk (0x7ul << CLK_CLKSEL1_CLKOSEL_Pos) /*!< CLK_T::CLKSEL1: CLKOSEL Mask */ #define CLK_CLKSEL1_TMR0SEL_Pos (8) /*!< CLK_T::CLKSEL1: TMR0SEL Position */ #define CLK_CLKSEL1_TMR0SEL_Msk (0x7ul << CLK_CLKSEL1_TMR0SEL_Pos) /*!< CLK_T::CLKSEL1: TMR0SEL Mask */ #define CLK_CLKSEL1_TMR1SEL_Pos (12) /*!< CLK_T::CLKSEL1: TMR1SEL Position */ #define CLK_CLKSEL1_TMR1SEL_Msk (0x7ul << CLK_CLKSEL1_TMR1SEL_Pos) /*!< CLK_T::CLKSEL1: TMR1SEL Mask */ #define CLK_CLKSEL1_TMR2SEL_Pos (16) /*!< CLK_T::CLKSEL1: TMR2SEL Position */ #define CLK_CLKSEL1_TMR2SEL_Msk (0x7ul << CLK_CLKSEL1_TMR2SEL_Pos) /*!< CLK_T::CLKSEL1: TMR2SEL Mask */ #define CLK_CLKSEL1_TMR3SEL_Pos (20) /*!< CLK_T::CLKSEL1: TMR3SEL Position */ #define CLK_CLKSEL1_TMR3SEL_Msk (0x7ul << CLK_CLKSEL1_TMR3SEL_Pos) /*!< CLK_T::CLKSEL1: TMR3SEL Mask */ #define CLK_CLKSEL1_UART0SEL_Pos (24) /*!< CLK_T::CLKSEL1: UART0SEL Position */ #define CLK_CLKSEL1_UART0SEL_Msk (0x7ul << CLK_CLKSEL1_UART0SEL_Pos) /*!< CLK_T::CLKSEL1: UART0SEL Mask */ #define CLK_CLKSEL1_UART1SEL_Pos (28) /*!< CLK_T::CLKSEL1: UART1SEL Position */ #define CLK_CLKSEL1_UART1SEL_Msk (0x7ul << CLK_CLKSEL1_UART1SEL_Pos) /*!< CLK_T::CLKSEL1: UART1SEL Mask */ #define CLK_CLKSEL2_PWM0SEL_Pos (0) /*!< CLK_T::CLKSEL2: PWM0SEL Position */ #define CLK_CLKSEL2_PWM0SEL_Msk (0x1ul << CLK_CLKSEL2_PWM0SEL_Pos) /*!< CLK_T::CLKSEL2: PWM0SEL Mask */ #define CLK_CLKSEL2_PWM1SEL_Pos (1) /*!< CLK_T::CLKSEL2: PWM1SEL Position */ #define CLK_CLKSEL2_PWM1SEL_Msk (0x1ul << CLK_CLKSEL2_PWM1SEL_Pos) /*!< CLK_T::CLKSEL2: PWM1SEL Mask */ #define CLK_CLKSEL2_QSPI0SEL_Pos (2) /*!< CLK_T::CLKSEL2: QSPI0SEL Position */ #define CLK_CLKSEL2_QSPI0SEL_Msk (0x3ul << CLK_CLKSEL2_QSPI0SEL_Pos) /*!< CLK_T::CLKSEL2: QSPI0SEL Mask */ #define CLK_CLKSEL2_SPI0SEL_Pos (4) /*!< CLK_T::CLKSEL2: SPI0SEL Position */ #define CLK_CLKSEL2_SPI0SEL_Msk (0x3ul << CLK_CLKSEL2_SPI0SEL_Pos) /*!< CLK_T::CLKSEL2: SPI0SEL Mask */ #define CLK_CLKSEL2_SPI1SEL_Pos (6) /*!< CLK_T::CLKSEL2: SPI1SEL Position */ #define CLK_CLKSEL2_SPI1SEL_Msk (0x3ul << CLK_CLKSEL2_SPI1SEL_Pos) /*!< CLK_T::CLKSEL2: SPI1SEL Mask */ #define CLK_CLKSEL2_BPWM0SEL_Pos (8) /*!< CLK_T::CLKSEL2: BPWM0SEL Position */ #define CLK_CLKSEL2_BPWM0SEL_Msk (0x1ul << CLK_CLKSEL2_BPWM0SEL_Pos) /*!< CLK_T::CLKSEL2: BPWM0SEL Mask */ #define CLK_CLKSEL2_BPWM1SEL_Pos (9) /*!< CLK_T::CLKSEL2: BPWM1SEL Position */ #define CLK_CLKSEL2_BPWM1SEL_Msk (0x1ul << CLK_CLKSEL2_BPWM1SEL_Pos) /*!< CLK_T::CLKSEL2: BPWM1SEL Mask */ #define CLK_CLKSEL2_LCDSEL_Pos (24) /*!< CLK_T::CLKSEL2: LCDSEL Position */ #define CLK_CLKSEL2_LCDSEL_Msk (0x1ul << CLK_CLKSEL2_LCDSEL_Pos) /*!< CLK_T::CLKSEL2: LCDSEL Mask */ #define CLK_CLKSEL2_LCDCPSEL_Pos (25) /*!< CLK_T::CLKSEL2: LCDCPSEL Position */ #define CLK_CLKSEL2_LCDCPSEL_Msk (0x1ul << CLK_CLKSEL2_LCDCPSEL_Pos) /*!< CLK_T::CLKSEL2: LCDCPSEL Mask */ #define CLK_CLKSEL2_PSIOSEL_Pos (28) /*!< CLK_T::CLKSEL2: PSIOSEL Position */ #define CLK_CLKSEL2_PSIOSEL_Msk (0x7ul << CLK_CLKSEL2_PSIOSEL_Pos) /*!< CLK_T::CLKSEL2: PSIOSEL Mask */ #define CLK_CLKSEL3_SC0SEL_Pos (0) /*!< CLK_T::CLKSEL3: SC0SEL Position */ #define CLK_CLKSEL3_SC0SEL_Msk (0x3ul << CLK_CLKSEL3_SC0SEL_Pos) /*!< CLK_T::CLKSEL3: SC0SEL Mask */ #define CLK_CLKSEL3_UART2SEL_Pos (24) /*!< CLK_T::CLKSEL3: UART2SEL Position */ #define CLK_CLKSEL3_UART2SEL_Msk (0x7ul << CLK_CLKSEL3_UART2SEL_Pos) /*!< CLK_T::CLKSEL3: UART2SEL Mask */ #define CLK_CLKSEL3_UART3SEL_Pos (28) /*!< CLK_T::CLKSEL3: UART3SEL Position */ #define CLK_CLKSEL3_UART3SEL_Msk (0x7ul << CLK_CLKSEL3_UART3SEL_Pos) /*!< CLK_T::CLKSEL3: UART3SEL Mask */ #define CLK_CLKDIV0_HCLKDIV_Pos (0) /*!< CLK_T::CLKDIV0: HCLKDIV Position */ #define CLK_CLKDIV0_HCLKDIV_Msk (0xful << CLK_CLKDIV0_HCLKDIV_Pos) /*!< CLK_T::CLKDIV0: HCLKDIV Mask */ #define CLK_CLKDIV0_USBDIV_Pos (4) /*!< CLK_T::CLKDIV0: USBDIV Position */ #define CLK_CLKDIV0_USBDIV_Msk (0xful << CLK_CLKDIV0_USBDIV_Pos) /*!< CLK_T::CLKDIV0: USBDIV Mask */ #define CLK_CLKDIV0_UART0DIV_Pos (8) /*!< CLK_T::CLKDIV0: UART0DIV Position */ #define CLK_CLKDIV0_UART0DIV_Msk (0xful << CLK_CLKDIV0_UART0DIV_Pos) /*!< CLK_T::CLKDIV0: UART0DIV Mask */ #define CLK_CLKDIV0_UART1DIV_Pos (12) /*!< CLK_T::CLKDIV0: UART1DIV Position */ #define CLK_CLKDIV0_UART1DIV_Msk (0xful << CLK_CLKDIV0_UART1DIV_Pos) /*!< CLK_T::CLKDIV0: UART1DIV Mask */ #define CLK_CLKDIV0_EADCDIV_Pos (16) /*!< CLK_T::CLKDIV0: EADCDIV Position */ #define CLK_CLKDIV0_EADCDIV_Msk (0xfful << CLK_CLKDIV0_EADCDIV_Pos) /*!< CLK_T::CLKDIV0: EADCDIV Mask */ #define CLK_CLKDIV1_SC0DIV_Pos (0) /*!< CLK_T::CLKDIV1: SC0DIV Position */ #define CLK_CLKDIV1_SC0DIV_Msk (0xfful << CLK_CLKDIV1_SC0DIV_Pos) /*!< CLK_T::CLKDIV1: SC0DIV Mask */ #define CLK_CLKDIV1_PSIODIV_Pos (24) /*!< CLK_T::CLKDIV1: PSIODIV Position */ #define CLK_CLKDIV1_PSIODIV_Msk (0xfful << CLK_CLKDIV1_PSIODIV_Pos) /*!< CLK_T::CLKDIV1: PSIODIV Mask */ #define CLK_CLKDIV4_UART2DIV_Pos (0) /*!< CLK_T::CLKDIV4: UART2DIV Position */ #define CLK_CLKDIV4_UART2DIV_Msk (0xful << CLK_CLKDIV4_UART2DIV_Pos) /*!< CLK_T::CLKDIV4: UART2DIV Mask */ #define CLK_CLKDIV4_UART3DIV_Pos (4) /*!< CLK_T::CLKDIV4: UART3DIV Position */ #define CLK_CLKDIV4_UART3DIV_Msk (0xful << CLK_CLKDIV4_UART3DIV_Pos) /*!< CLK_T::CLKDIV4: UART3DIV Mask */ #define CLK_PCLKDIV_APB0DIV_Pos (0) /*!< CLK_T::PCLKDIV: APB0DIV Position */ #define CLK_PCLKDIV_APB0DIV_Msk (0x7ul << CLK_PCLKDIV_APB0DIV_Pos) /*!< CLK_T::PCLKDIV: APB0DIV Mask */ #define CLK_PCLKDIV_APB1DIV_Pos (4) /*!< CLK_T::PCLKDIV: APB1DIV Position */ #define CLK_PCLKDIV_APB1DIV_Msk (0x7ul << CLK_PCLKDIV_APB1DIV_Pos) /*!< CLK_T::PCLKDIV: APB1DIV Mask */ #define CLK_PLLCTL_FBDIV_Pos (0) /*!< CLK_T::PLLCTL: FBDIV Position */ #define CLK_PLLCTL_FBDIV_Msk (0x3ful << CLK_PLLCTL_FBDIV_Pos) /*!< CLK_T::PLLCTL: FBDIV Mask */ #define CLK_PLLCTL_INDIV_Pos (9) /*!< CLK_T::PLLCTL: INDIV Position */ #define CLK_PLLCTL_INDIV_Msk (0xful << CLK_PLLCTL_INDIV_Pos) /*!< CLK_T::PLLCTL: INDIV Mask */ #define CLK_PLLCTL_OUTDIV_Pos (14) /*!< CLK_T::PLLCTL: OUTDIV Position */ #define CLK_PLLCTL_OUTDIV_Msk (0x3ul << CLK_PLLCTL_OUTDIV_Pos) /*!< CLK_T::PLLCTL: OUTDIV Mask */ #define CLK_PLLCTL_PD_Pos (16) /*!< CLK_T::PLLCTL: PD Position */ #define CLK_PLLCTL_PD_Msk (0x1ul << CLK_PLLCTL_PD_Pos) /*!< CLK_T::PLLCTL: PD Mask */ #define CLK_PLLCTL_BP_Pos (17) /*!< CLK_T::PLLCTL: BP Position */ #define CLK_PLLCTL_BP_Msk (0x1ul << CLK_PLLCTL_BP_Pos) /*!< CLK_T::PLLCTL: BP Mask */ #define CLK_PLLCTL_OE_Pos (18) /*!< CLK_T::PLLCTL: OE Position */ #define CLK_PLLCTL_OE_Msk (0x1ul << CLK_PLLCTL_OE_Pos) /*!< CLK_T::PLLCTL: OE Mask */ #define CLK_PLLCTL_PLLSRC_Pos (19) /*!< CLK_T::PLLCTL: PLLSRC Position */ #define CLK_PLLCTL_PLLSRC_Msk (0x3ul << CLK_PLLCTL_PLLSRC_Pos) /*!< CLK_T::PLLCTL: PLLSRC Mask */ #define CLK_PLLCTL_STBSEL_Pos (23) /*!< CLK_T::PLLCTL: STBSEL Position */ #define CLK_PLLCTL_STBSEL_Msk (0x1ul << CLK_PLLCTL_STBSEL_Pos) /*!< CLK_T::PLLCTL: STBSEL Mask */ #define CLK_PLLCTL_PLL_CLF_EN_Pos (24) /*!< CLK_T::PLLCTL: PLL_CLF_EN Position */ #define CLK_PLLCTL_PLL_CLF_EN_Msk (0x1ul << CLK_PLLCTL_PLL_CLF_EN_Pos) /*!< CLK_T::PLLCTL: PLL_CLF_EN Mask */ #define CLK_STATUS_HXTSTB_Pos (0) /*!< CLK_T::STATUS: HXTSTB Position */ #define CLK_STATUS_HXTSTB_Msk (0x1ul << CLK_STATUS_HXTSTB_Pos) /*!< CLK_T::STATUS: HXTSTB Mask */ #define CLK_STATUS_LXTSTB_Pos (1) /*!< CLK_T::STATUS: LXTSTB Position */ #define CLK_STATUS_LXTSTB_Msk (0x1ul << CLK_STATUS_LXTSTB_Pos) /*!< CLK_T::STATUS: LXTSTB Mask */ #define CLK_STATUS_PLLSTB_Pos (2) /*!< CLK_T::STATUS: PLLSTB Position */ #define CLK_STATUS_PLLSTB_Msk (0x1ul << CLK_STATUS_PLLSTB_Pos) /*!< CLK_T::STATUS: PLLSTB Mask */ #define CLK_STATUS_LIRCSTB_Pos (3) /*!< CLK_T::STATUS: LIRCSTB Position */ #define CLK_STATUS_LIRCSTB_Msk (0x1ul << CLK_STATUS_LIRCSTB_Pos) /*!< CLK_T::STATUS: LIRCSTB Mask */ #define CLK_STATUS_HIRCSTB_Pos (4) /*!< CLK_T::STATUS: HIRCSTB Position */ #define CLK_STATUS_HIRCSTB_Msk (0x1ul << CLK_STATUS_HIRCSTB_Pos) /*!< CLK_T::STATUS: HIRCSTB Mask */ #define CLK_STATUS_MIRCSTB_Pos (6) /*!< CLK_T::STATUS: MIRCSTB Position */ #define CLK_STATUS_MIRCSTB_Msk (0x1ul << CLK_STATUS_MIRCSTB_Pos) /*!< CLK_T::STATUS: MIRCSTB Mask */ #define CLK_STATUS_CLKSFAIL_Pos (7) /*!< CLK_T::STATUS: CLKSFAIL Position */ #define CLK_STATUS_CLKSFAIL_Msk (0x1ul << CLK_STATUS_CLKSFAIL_Pos) /*!< CLK_T::STATUS: CLKSFAIL Mask */ #define CLK_CLKOCTL_FREQSEL_Pos (0) /*!< CLK_T::CLKOCTL: FREQSEL Position */ #define CLK_CLKOCTL_FREQSEL_Msk (0xful << CLK_CLKOCTL_FREQSEL_Pos) /*!< CLK_T::CLKOCTL: FREQSEL Mask */ #define CLK_CLKOCTL_CLKOEN_Pos (4) /*!< CLK_T::CLKOCTL: CLKOEN Position */ #define CLK_CLKOCTL_CLKOEN_Msk (0x1ul << CLK_CLKOCTL_CLKOEN_Pos) /*!< CLK_T::CLKOCTL: CLKOEN Mask */ #define CLK_CLKOCTL_DIV1EN_Pos (5) /*!< CLK_T::CLKOCTL: DIV1EN Position */ #define CLK_CLKOCTL_DIV1EN_Msk (0x1ul << CLK_CLKOCTL_DIV1EN_Pos) /*!< CLK_T::CLKOCTL: DIV1EN Mask */ #define CLK_CLKOCTL_CLK1HZEN_Pos (6) /*!< CLK_T::CLKOCTL: CLK1HZEN Position */ #define CLK_CLKOCTL_CLK1HZEN_Msk (0x1ul << CLK_CLKOCTL_CLK1HZEN_Pos) /*!< CLK_T::CLKOCTL: CLK1HZEN Mask */ #define CLK_CLKDCTL_HXTFDEN_Pos (4) /*!< CLK_T::CLKDCTL: HXTFDEN Position */ #define CLK_CLKDCTL_HXTFDEN_Msk (0x1ul << CLK_CLKDCTL_HXTFDEN_Pos) /*!< CLK_T::CLKDCTL: HXTFDEN Mask */ #define CLK_CLKDCTL_HXTFIEN_Pos (5) /*!< CLK_T::CLKDCTL: HXTFIEN Position */ #define CLK_CLKDCTL_HXTFIEN_Msk (0x1ul << CLK_CLKDCTL_HXTFIEN_Pos) /*!< CLK_T::CLKDCTL: HXTFIEN Mask */ #define CLK_CLKDCTL_LXTFDEN_Pos (12) /*!< CLK_T::CLKDCTL: LXTFDEN Position */ #define CLK_CLKDCTL_LXTFDEN_Msk (0x1ul << CLK_CLKDCTL_LXTFDEN_Pos) /*!< CLK_T::CLKDCTL: LXTFDEN Mask */ #define CLK_CLKDCTL_LXTFIEN_Pos (13) /*!< CLK_T::CLKDCTL: LXTFIEN Position */ #define CLK_CLKDCTL_LXTFIEN_Msk (0x1ul << CLK_CLKDCTL_LXTFIEN_Pos) /*!< CLK_T::CLKDCTL: LXTFIEN Mask */ #define CLK_CLKDCTL_HXTFQDEN_Pos (16) /*!< CLK_T::CLKDCTL: HXTFQDEN Position */ #define CLK_CLKDCTL_HXTFQDEN_Msk (0x1ul << CLK_CLKDCTL_HXTFQDEN_Pos) /*!< CLK_T::CLKDCTL: HXTFQDEN Mask */ #define CLK_CLKDCTL_HXTFQIEN_Pos (17) /*!< CLK_T::CLKDCTL: HXTFQIEN Position */ #define CLK_CLKDCTL_HXTFQIEN_Msk (0x1ul << CLK_CLKDCTL_HXTFQIEN_Pos) /*!< CLK_T::CLKDCTL: HXTFQIEN Mask */ #define CLK_CLKDSTS_HXTFIF_Pos (0) /*!< CLK_T::CLKDSTS: HXTFIF Position */ #define CLK_CLKDSTS_HXTFIF_Msk (0x1ul << CLK_CLKDSTS_HXTFIF_Pos) /*!< CLK_T::CLKDSTS: HXTFIF Mask */ #define CLK_CLKDSTS_LXTFIF_Pos (1) /*!< CLK_T::CLKDSTS: LXTFIF Position */ #define CLK_CLKDSTS_LXTFIF_Msk (0x1ul << CLK_CLKDSTS_LXTFIF_Pos) /*!< CLK_T::CLKDSTS: LXTFIF Mask */ #define CLK_CLKDSTS_HXTFQIF_Pos (8) /*!< CLK_T::CLKDSTS: HXTFQIF Position */ #define CLK_CLKDSTS_HXTFQIF_Msk (0x1ul << CLK_CLKDSTS_HXTFQIF_Pos) /*!< CLK_T::CLKDSTS: HXTFQIF Mask */ #define CLK_CDUPB_UPERBD_Pos (0) /*!< CLK_T::CDUPB: UPERBD Position */ #define CLK_CDUPB_UPERBD_Msk (0x3fful << CLK_CDUPB_UPERBD_Pos) /*!< CLK_T::CDUPB: UPERBD Mask */ #define CLK_CDLOWB_LOWERBD_Pos (0) /*!< CLK_T::CDLOWB: LOWERBD Position */ #define CLK_CDLOWB_LOWERBD_Msk (0x3fful << CLK_CDLOWB_LOWERBD_Pos) /*!< CLK_T::CDLOWB: LOWERBD Mask */ #define CLK_PMUCTL_PDMSEL_Pos (0) /*!< CLK_T::PMUCTL: PDMSEL Position */ #define CLK_PMUCTL_PDMSEL_Msk (0x7ul << CLK_PMUCTL_PDMSEL_Pos) /*!< CLK_T::PMUCTL: PDMSEL Mask */ #define CLK_PMUCTL_WKTMREN_Pos (8) /*!< CLK_T::PMUCTL: WKTMREN Position */ #define CLK_PMUCTL_WKTMREN_Msk (0x1ul << CLK_PMUCTL_WKTMREN_Pos) /*!< CLK_T::PMUCTL: WKTMREN Mask */ #define CLK_PMUCTL_WKTMRIS_Pos (9) /*!< CLK_T::PMUCTL: WKTMRIS Position */ #define CLK_PMUCTL_WKTMRIS_Msk (0x7ul << CLK_PMUCTL_WKTMRIS_Pos) /*!< CLK_T::PMUCTL: WKTMRIS Mask */ #define CLK_PMUCTL_WKPINEN0_Pos (16) /*!< CLK_T::PMUCTL: WKPINEN0 Position */ #define CLK_PMUCTL_WKPINEN0_Msk (0x3ul << CLK_PMUCTL_WKPINEN0_Pos) /*!< CLK_T::PMUCTL: WKPINEN0 Mask */ #define CLK_PMUCTL_WKPINDBEN_Pos (22) /*!< CLK_T::PMUCTL: WKPINDBEN Position */ #define CLK_PMUCTL_WKPINDBEN_Msk (0x1ul << CLK_PMUCTL_WKPINDBEN_Pos) /*!< CLK_T::PMUCTL: WKPINDBEN Mask */ #define CLK_PMUCTL_RTCWKEN_Pos (23) /*!< CLK_T::PMUCTL: RTCWKEN Position */ #define CLK_PMUCTL_RTCWKEN_Msk (0x1ul << CLK_PMUCTL_RTCWKEN_Pos) /*!< CLK_T::PMUCTL: RTCWKEN Mask */ #define CLK_PMUCTL_WKPINEN1_Pos (24) /*!< CLK_T::PMUCTL: WKPINEN1 Position */ #define CLK_PMUCTL_WKPINEN1_Msk (0x3ul << CLK_PMUCTL_WKPINEN1_Pos) /*!< CLK_T::PMUCTL: WKPINEN1 Mask */ #define CLK_PMUCTL_WKPINEN2_Pos (26) /*!< CLK_T::PMUCTL: WKPINEN2 Position */ #define CLK_PMUCTL_WKPINEN2_Msk (0x3ul << CLK_PMUCTL_WKPINEN2_Pos) /*!< CLK_T::PMUCTL: WKPINEN2 Mask */ #define CLK_PMUCTL_WKPINEN3_Pos (28) /*!< CLK_T::PMUCTL: WKPINEN3 Position */ #define CLK_PMUCTL_WKPINEN3_Msk (0x3ul << CLK_PMUCTL_WKPINEN3_Pos) /*!< CLK_T::PMUCTL: WKPINEN3 Mask */ #define CLK_PMUCTL_WKPINEN4_Pos (30) /*!< CLK_T::PMUCTL: WKPINEN4 Position */ #define CLK_PMUCTL_WKPINEN4_Msk (0x3ul << CLK_PMUCTL_WKPINEN4_Pos) /*!< CLK_T::PMUCTL: WKPINEN4 Mask */ #define CLK_PMUSTS_PINWK0_Pos (0) /*!< CLK_T::PMUSTS: PINWK0 Position */ #define CLK_PMUSTS_PINWK0_Msk (0x1ul << CLK_PMUSTS_PINWK0_Pos) /*!< CLK_T::PMUSTS: PINWK0 Mask */ #define CLK_PMUSTS_TMRWK_Pos (1) /*!< CLK_T::PMUSTS: TMRWK Position */ #define CLK_PMUSTS_TMRWK_Msk (0x1ul << CLK_PMUSTS_TMRWK_Pos) /*!< CLK_T::PMUSTS: TMRWK Mask */ #define CLK_PMUSTS_RTCWK_Pos (2) /*!< CLK_T::PMUSTS: RTCWK Position */ #define CLK_PMUSTS_RTCWK_Msk (0x1ul << CLK_PMUSTS_RTCWK_Pos) /*!< CLK_T::PMUSTS: RTCWK Mask */ #define CLK_PMUSTS_PINWK1_Pos (3) /*!< CLK_T::PMUSTS: PINWK1 Position */ #define CLK_PMUSTS_PINWK1_Msk (0x1ul << CLK_PMUSTS_PINWK1_Pos) /*!< CLK_T::PMUSTS: PINWK1 Mask */ #define CLK_PMUSTS_PINWK2_Pos (4) /*!< CLK_T::PMUSTS: PINWK2 Position */ #define CLK_PMUSTS_PINWK2_Msk (0x1ul << CLK_PMUSTS_PINWK2_Pos) /*!< CLK_T::PMUSTS: PINWK2 Mask */ #define CLK_PMUSTS_PINWK3_Pos (5) /*!< CLK_T::PMUSTS: PINWK3 Position */ #define CLK_PMUSTS_PINWK3_Msk (0x1ul << CLK_PMUSTS_PINWK3_Pos) /*!< CLK_T::PMUSTS: PINWK3 Mask */ #define CLK_PMUSTS_PINWK4_Pos (6) /*!< CLK_T::PMUSTS: PINWK4 Position */ #define CLK_PMUSTS_PINWK4_Msk (0x1ul << CLK_PMUSTS_PINWK4_Pos) /*!< CLK_T::PMUSTS: PINWK4 Mask */ #define CLK_PMUSTS_LVRWK_Pos (12) /*!< CLK_T::PMUSTS: LVRWK Position */ #define CLK_PMUSTS_LVRWK_Msk (0x1ul << CLK_PMUSTS_LVRWK_Pos) /*!< CLK_T::PMUSTS: LVRWK Mask */ #define CLK_PMUSTS_CLRWK_Pos (31) /*!< CLK_T::PMUSTS: CLRWK Position */ #define CLK_PMUSTS_CLRWK_Msk (0x1ul << CLK_PMUSTS_CLRWK_Pos) /*!< CLK_T::PMUSTS: CLRWK Mask */ #define CLK_HXTFSEL_HXTFSEL_Pos (0) /*!< CLK_T::HXTFSEL: HXTFSEL Position */ #define CLK_HXTFSEL_HXTFSEL_Msk (0x1ul << CLK_HXTFSEL_HXTFSEL_Pos) /*!< CLK_T::HXTFSEL: HXTFSEL Mask */ /** @} CLK_CONST */ /** @} end of CLK register group */ /** @} end of REGISTER group */ #if defined ( __CC_ARM ) #pragma no_anon_unions #endif #endif /* __CLK_REG_H__ */