mirror of
https://github.com/dougg3/mac-rom-simm-programmer.git
synced 2024-11-29 06:49:20 +00:00
1220 lines
94 KiB
C
1220 lines
94 KiB
C
/**************************************************************************//**
|
|
* @file clk_reg.h
|
|
* @version V1.00
|
|
* @brief CLK register definition header file
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
* @copyright (C) 2020 Nuvoton Technology Corp. All rights reserved.
|
|
*****************************************************************************/
|
|
|
|
#ifndef __CLK_REG_H__
|
|
#define __CLK_REG_H__
|
|
|
|
#if defined ( __CC_ARM )
|
|
#pragma anon_unions
|
|
#endif
|
|
|
|
/**
|
|
@addtogroup REGISTER Control Register
|
|
@{
|
|
*/
|
|
|
|
/**
|
|
@addtogroup CLK System Clock Controller (CLK)
|
|
Memory Mapped Structure for CLK Controller
|
|
@{
|
|
*/
|
|
|
|
typedef struct
|
|
{
|
|
|
|
|
|
/**
|
|
* @var CLK_T::PWRCTL
|
|
* Offset: 0x00 System Power-down Control Register
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[0] |HXTEN |HXT Enable Bit (Write Protect)
|
|
* | | |The bit default value is set by flash controller user configuration register CONFIG0 [26]
|
|
* | | |When the default clock source is from HXT, this bit is set to 1 automatically.
|
|
* | | |0 = 4~32 MHz external high speed crystal (HXT) Disabled.
|
|
* | | |1 = 4~32 MHz external high speed crystal (HXT) Enabled.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[1] |LXTEN |LXT Enable Bit (Write Protect)
|
|
* | | |0 = 32.768 kHz external low speed crystal (LXT) Disabled.
|
|
* | | |1 = 32.768 kHz external low speed crystal (LXT) Enabled.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[2] |HIRCEN |HIRC Enable Bit (Write Protect)
|
|
* | | |0 = 48MHz internal high speed RC oscillator (HIRC) Disabled.
|
|
* | | |1 = 48 MHz internal high speed RC oscillator (HIRC) Enabled.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[3] |LIRCEN |LIRC Enable Bit (Write Protect)
|
|
* | | |0 = 38.4 kHz internal low speed RC oscillator (LIRC) Disabled.
|
|
* | | |1 = 38.4 kHz internal low speed RC oscillator (LIRC) Enabled.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* | | |Note : LIRC will also be forced on when 1
|
|
* | | |Power down and ~(cfg0[3] & cfg0[4] & ~cfg0[31] & cfg0[30]) 2
|
|
* | | |Not power down and ~(cfg0[3] & cfg0[4] & cfg0[31])
|
|
* |[4] |PDWKDLY |Enable the Wake-up Delay Counter (Write Protect)
|
|
* | | |When the chip wakes up from Power-down mode, the clock control will delay certain clock cycles to wait system clock stable.
|
|
* | | |The delayed clock cycle is 4096 clock cycles when chip works at 4~32 MHz external high speed crystal oscillator (HXT), HIRC and MIRC see HIRCSTBS and MIRCSTBS
|
|
* | | |0 = Clock cycles delay Disabled.
|
|
* | | |1 = Clock cycles delay Enabled.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[5] |PDWKIEN |Power-down Mode Wake-up Interrupt Enable Bit (Write Protect)
|
|
* | | |0 = Power-down mode wake-up interrupt Disabled.
|
|
* | | |1 = Power-down mode wake-up interrupt Enabled.
|
|
* | | |Note1: The interrupt will occur when both PDWKIF and PDWKIEN are high.
|
|
* | | |Note2: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[6] |PDWKIF |Power-down Mode Wake-up Interrupt Status
|
|
* | | |Set by "Power-down wake-up event", it indicates that resume from Power-down mode.
|
|
* | | |The flag is set if any wake-up source is occurred. Refer Power Modes and Wake-up Sources chapter.
|
|
* | | |Note1: Write 1 to clear the bit to 0.
|
|
* | | |Note2: This bit works only if PDWKIEN (CLK_PWRCTL[5]) set to 1.
|
|
* |[7] |PDEN |System Power-down Enable (Write Protect)
|
|
* | | |When this bit is set to 1, Power-down mode is enabled and chip Power-down behavior will depend on the PDWTCPU bit.
|
|
* | | |(a) If the PDWTCPU is 0, then the chip enters Power-down mode immediately after the PDEN bit set
|
|
* | | |(default)
|
|
* | | |(b) if the PDWTCPU is 1, then the chip keeps active till the CPU sleep mode is also active and then the chip enters Power-down mode.
|
|
* | | |When chip wakes up from Power-down mode, this bit is auto cleared
|
|
* | | |Users need to set this bit again for next Power-down.
|
|
* | | |In Power-down mode, HXT and the HIRC will be disabled in this mode, but LXT and LIRC are not controlled by Power-down mode.
|
|
* | | |In Power-down mode, the PLL and system clock are disabled, and ignored the clock source selection
|
|
* | | |The clocks of peripheral are not controlled by Power-down mode, if the peripheral clock source is from LXT or LIRC.
|
|
* | | |0 = Chip operating normally or chip in idle mode because of WFI command.
|
|
* | | |1 = Chip enters Power-down mode instant or wait CPU sleep command WFI.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[19] |MIRCEN |MIRC Enable Bit (Write Protect)
|
|
* | | |0 = 4MHz internal high speed RC oscillator (MIRC) Disabled.
|
|
* | | |1 = 4 MHz internal high speed RC oscillator (MIRC) Enabled.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* | | |Note: Will be forced on when CLKSEL0[2:0] = 0x101b.
|
|
* |[22:20] |HXTGAIN |HXT Gain Control Bit (Write Protect)
|
|
* | | |This is a protected register. Please refer to open lock sequence to program it.
|
|
* | | |Gain control is used to enlarge the gain of crystal to make sure crystal work normally
|
|
* | | |If gain control is enabled, crystal will consume more power than gain control off.
|
|
* | | |000 = HXT frequency 1~4 MHz.
|
|
* | | |001 = HXT frequency 4~8 MHz.
|
|
* | | |010 = HXT frequency 8~12 MHz.
|
|
* | | |011 = HXT frequency 12~16 MHz.
|
|
* | | |100 = HXT frequency 12~24 MHz.
|
|
* | | |101 = HXT frequency 16~32 MHz.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* | | |Note : reset by power on reset
|
|
* @var CLK_T::AHBCLK
|
|
* Offset: 0x04 AHB Devices Clock Enable Control Register
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[1] |PDMACKEN |PDMA Controller Clock Enable Bit
|
|
* | | |0 = PDMA peripheral clock Disabled.
|
|
* | | |1 = PDMA peripheral clock Enabled.
|
|
* |[2] |ISPCKEN |Flash ISP Controller Clock Enable Bit
|
|
* | | |0 = Flash ISP peripheral clock Disabled.
|
|
* | | |1 = Flash ISP peripheral clock Enabled.
|
|
* |[3] |EBICKEN |EBI Controller Clock Enable Bit
|
|
* | | |0 = EBI peripheral clock Disabled.
|
|
* | | |1 = EBI peripheral clock Enabled.
|
|
* |[4] |EXSTCKEN |External System Tick Clock Enable Bit
|
|
* | | |0 = External System tick clock Disabled.
|
|
* | | |1 = External System tick clock Enabled.
|
|
* |[7] |CRCCKEN |CRC Generator Controller Clock Enable Bit
|
|
* | | |0 = CRC peripheral clock Disabled.
|
|
* | | |1 = CRC peripheral clock Enabled.
|
|
* |[12] |CRPTCKEN |Cryptographic Accelerator Clock Enable Bit
|
|
* | | |0 = Cryptographic Accelerator clock Disabled.
|
|
* | | |1 = Cryptographic Accelerator clock Enabled.
|
|
* |[15] |FMCIDLE |Flash Memory Controller Clock Enable Bit in IDLE Mode
|
|
* | | |0 = FMC clock Disabled when chip is under IDLE mode.
|
|
* | | |1 = FMC clock Enabled when chip is under IDLE mode.
|
|
* |[24] |GPACKEN |GPIOA Clock Enable Bit
|
|
* | | |0 = GPIOA port clock Disabled.
|
|
* | | |1 = GPIOA port clock Enabled.
|
|
* |[25] |GPBCKEN |GPIOB Clock Enable Bit
|
|
* | | |0 = GPIOB port clock Disabled.
|
|
* | | |1 = GPIOB port clock Enabled.
|
|
* |[26] |GPCCKEN |GPIOC Clock Enable Bit
|
|
* | | |0 = GPIOC port clock Disabled.
|
|
* | | |1 = GPIOC port clock Enabled.
|
|
* |[27] |GPDCKEN |GPIOD Clock Enable Bit
|
|
* | | |0 = GPIOD port clock Disabled.
|
|
* | | |1 = GPIOD port clock Enabled.
|
|
* |[28] |GPECKEN |GPIOE Clock Enable Bit
|
|
* | | |0 = GPIOE port clock Disabled.
|
|
* | | |1 = GPIOE port clock Enabled.
|
|
* |[29] |GPFCKEN |GPIOF Clock Enable Bit
|
|
* | | |0 = GPIOF port clock Disabled.
|
|
* | | |1 = GPIOF port clock Enabled.
|
|
* @var CLK_T::APBCLK0
|
|
* Offset: 0x08 APB Devices Clock Enable Control Register 0
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[0] |WDTCKEN |Watchdog Timer Clock Enable Bit (Write Protect)
|
|
* | | |0 = Watchdog timer clock Disabled.
|
|
* | | |1 = Watchdog timer clock Enabled.
|
|
* | | |Note 1: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* | | |Note 2: This bit is forced to 1 when CONFIG0[3] or CONFIG0[4] or CONFIG0[31] is 0.
|
|
* | | |Note 3: Reset by power on reset or watch dog reset or software chip reset.
|
|
* |[1] |RTCCKEN |Real-time-clock APB Interface Clock Enable Bit
|
|
* | | |0 = RTC APB clock Disabled.
|
|
* | | |1 = RTC APB clock Enabled.
|
|
* |[2] |TMR0CKEN |Timer0 Clock Enable Bit
|
|
* | | |0 = Timer0 clock Disabled.
|
|
* | | |1 = Timer0 clock Enabled.
|
|
* |[3] |TMR1CKEN |Timer1 Clock Enable Bit
|
|
* | | |0 = Timer1 clock Disabled.
|
|
* | | |1 = Timer1 clock Enabled.
|
|
* |[4] |TMR2CKEN |Timer2 Clock Enable Bit
|
|
* | | |0 = Timer2 clock Disabled.
|
|
* | | |1 = Timer2 clock Enabled.
|
|
* |[5] |TMR3CKEN |Timer3 Clock Enable Bit
|
|
* | | |0 = Timer3 clock Disabled.
|
|
* | | |1 = Timer3 clock Enabled.
|
|
* |[6] |CLKOCKEN |CLKO Clock Enable Bit
|
|
* | | |0 = CLKO clock Disabled.
|
|
* | | |1 = CLKO clock Enabled.
|
|
* |[7] |ACMP01CKEN|Analog Comparator 0/1 Clock Enable Bit
|
|
* | | |0 = Analog comparator 0/1 clock Disabled.
|
|
* | | |1 = Analog comparator 0/1 clock Enabled.
|
|
* |[8] |I2C0CKEN |I2C0 Clock Enable Bit
|
|
* | | |0 = I2C0 clock Disabled.
|
|
* | | |1 = I2C0 clock Enabled.
|
|
* |[9] |I2C1CKEN |I2C1 Clock Enable Bit
|
|
* | | |0 = I2C1 clock Disabled.
|
|
* | | |1 = I2C1 clock Enabled.
|
|
* |[12] |QSPI0CKEN |QSPI0 Clock Enable Bit
|
|
* | | |0 = QSPI0 clock Disabled.
|
|
* | | |1 = QSPI0 clock Enabled.
|
|
* |[13] |SPI0CKEN |SPI0 Clock Enable Bit
|
|
* | | |0 = SPI0 clock Disabled.
|
|
* | | |1 = SPI0 clock Enabled.
|
|
* |[16] |UART0CKEN |UART0 Clock Enable Bit
|
|
* | | |0 = UART0 clock Disabled.
|
|
* | | |1 = UART0 clock Enabled.
|
|
* |[17] |UART1CKEN |UART1 Clock Enable Bit
|
|
* | | |0 = UART1 clock Disabled.
|
|
* | | |1 = UART1 clock Enabled.
|
|
* |[18] |UART2CKEN |UART2 Clock Enable Bit
|
|
* | | |0 = UART2 clock Disabled.
|
|
* | | |1 = UART2 clock Enabled.
|
|
* |[27] |USBDCKEN |USB Device Clock Enable Bit
|
|
* | | |0 = USB Device clock Disabled.
|
|
* | | |1 = USB Device clock Enabled.
|
|
* |[28] |EADCCKEN |Enhanced Analog-digital-converter (EADC) Clock Enable Bit
|
|
* | | |0 = EADC clock Disabled.
|
|
* | | |1 = EADC clock Enabled.
|
|
* @var CLK_T::APBCLK1
|
|
* Offset: 0x0C APB Devices Clock Enable Control Register 1
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[0] |SC0CKEN |SC0 Clock Enable Bit
|
|
* | | |0 = SC0 clock Disabled.
|
|
* | | |1 = SC0 clock Enabled.
|
|
* |[8] |USCI0CKEN |USCI0 Clock Enable Bit
|
|
* | | |0 = USCI0 clock Disabled.
|
|
* | | |1 = USCI0 clock Enabled.
|
|
* |[9] |USCI1CKEN |USCI1 Clock Enable Bit
|
|
* | | |0 = USCI1 clock Disabled.
|
|
* | | |1 = USCI1 clock Enabled.
|
|
* |[10] |USCI2CKEN |USCI2 Clock Enable Bit
|
|
* | | |0 = USCI1 clock Disabled.
|
|
* | | |1 = USCI1 clock Enabled.
|
|
* |[12] |DACCKEN |DAC Clock Enable Bit
|
|
* | | |0 = DAC clock Disabled.
|
|
* | | |1 = DAC clock Enabled.
|
|
* |[16] |PWM0CKEN |PWM0 Clock Enable Bit
|
|
* | | |0 = PWM0 clock Disabled.
|
|
* | | |1 = PWM0 clock Enabled.
|
|
* |[17] |PWM1CKEN |PWM1 Clock Enable Bit
|
|
* | | |0 = PWM1 clock Disabled.
|
|
* | | |1 = PWM1 clock Enabled.
|
|
* |[18] |BPWM0CKEN |BPWM0 Clock Enable Bit
|
|
* | | |0 = BPWM0 clock Disabled.
|
|
* | | |1 = BPWM0 clock Enabled.
|
|
* |[19] |BPWM1CKEN |BPWM1 Clock Enable Bit
|
|
* | | |0 = BPWM1 clock Disabled.
|
|
* | | |1 = BPWM1 clock Enabled.
|
|
* |[30] |OPACKEN |OP Amplifier (OPA) Clock Enable Bit
|
|
* | | |0 = OPA clock Disabled.
|
|
* | | |1 = OPA clock Enabled.
|
|
* |[31] |PSIOCKEN |PSIO Clock Enable Bit
|
|
* | | |0 = PSIO clock Disabled.
|
|
* | | |1 = PSIO clock Enabled.
|
|
* @var CLK_T::CLKSEL0
|
|
* Offset: 0x10 Clock Source Select Control Register 0
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[2:0] |HCLKSEL |HCLK Clock Source Selection (Write Protect)
|
|
* | | |Before clock switching, the related clock sources (both pre-select and new-select) must be turned on.
|
|
* | | |The default value is reloaded from the value of CFOSC (CONFIG0[26]) in user configuration register of Flash controller by any reset
|
|
* | | |Therefore the default value is either 000b or 101b.
|
|
* | | |000 = Clock source from HXT.
|
|
* | | |001 = Clock source from LXT.
|
|
* | | |010 = Clock source from PLL.
|
|
* | | |011 = Clock source from LIRC.
|
|
* | | |101= Clock source from MIRC.
|
|
* | | |111= Clock source from HIRC.
|
|
* | | |Other = Reserved.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[5:3] |STCLKSEL |Cortex-M23 SysTick Clock Source Selection (Write Protect)
|
|
* | | |If SYST_CTRL[2]=0, SysTick uses listed clock source below.
|
|
* | | |000 = Clock source from HXT.
|
|
* | | |001 = Clock source from LXT.
|
|
* | | |010 = Clock source from HXT/2.
|
|
* | | |011 = Clock source from HCLK/2.
|
|
* | | |111 = Clock source from HIRC/2.
|
|
* | | |Note: if SysTick clock source is not from HCLK (i.e
|
|
* | | |SYST_CTRL[2] = 0), SysTick clock source must less than or equal to HCLK/2.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[8] |USBDSEL |USB Device Clock Source Selection (Write Protect)
|
|
* | | |These bits are protected bit
|
|
* | | |It means programming this bit needs to write "59h", "16h", "88h" to address 0x4000_0100 to disable register protection
|
|
* | | |Refer to the register REGWRPROT at address GCR_BA+0x100.
|
|
* | | |0 = Clock source from HIRC.
|
|
* | | |1 = Clock source from PLL. divided
|
|
* @var CLK_T::CLKSEL1
|
|
* Offset: 0x14 Clock Source Select Control Register 1
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[1:0] |WDTSEL |Watchdog Timer Clock Source Selection (Write Protect)
|
|
* | | |00 = Reserved.
|
|
* | | |01 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT).
|
|
* | | |10 = Clock source from HCLK/2048.
|
|
* | | |11 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC).
|
|
* | | |Note: This bit is write protected.Refer to the SYS_REGLCTL register
|
|
* | | |Note: This bit is forced to 11 when CONFIG0[31], CONFIG0[4], CONFIG0[3] are all ones.
|
|
* |[3:2] |WWDTSEL |Window Watchdog Timer Clock Source Selection (Write Protect)
|
|
* | | |10 = Clock source from HCLK/2048.
|
|
* | | |11 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC).
|
|
* | | |Others = Reserved.
|
|
* |[6:4] |CLKOSEL |Clock Divider Clock Source Selection
|
|
* | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT).
|
|
* | | |001 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT).
|
|
* | | |010 = Clock source from HCLK.
|
|
* | | |011 = Clock source from 48 MHz internal high speed RC oscillator (HIRC).
|
|
* | | |100 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC).
|
|
* | | |101 = Clock source from 4 MHz internal medium speed RC oscillator (MIRC).
|
|
* | | |110 = Clock source from PLL.
|
|
* | | |111 = Clock source from internal USB synchronous mode.
|
|
* |[10:8] |TMR0SEL |TIMER0 Clock Source Selection
|
|
* | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT).
|
|
* | | |001 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT).
|
|
* | | |010 = Clock source from PCLK0.
|
|
* | | |011 = Clock source from external clock T0 pin.
|
|
* | | |101 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC).
|
|
* | | |111 = Clock source from 48 MHz internal high speed RC oscillator (HIRC).
|
|
* | | |Others = Reserved.
|
|
* |[14:12] |TMR1SEL |TIMER1 Clock Source Selection
|
|
* | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT).
|
|
* | | |001 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT).
|
|
* | | |010 = Clock source from PCLK0.
|
|
* | | |011 = Clock source from external clock T1 pin.
|
|
* | | |101 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC).
|
|
* | | |111 = Clock source from 48 MHz internal high speed RC oscillator (HIRC).
|
|
* | | |Others = Reserved.
|
|
* |[18:16] |TMR2SEL |TIMER2 Clock Source Selection
|
|
* | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT).
|
|
* | | |001 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT).
|
|
* | | |010 = Clock source from PCLK1.
|
|
* | | |011 = Clock source from external clock T2 pin.
|
|
* | | |101 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC).
|
|
* | | |111 = Clock source from 48 MHz internal high speed RC oscillator (HIRC).
|
|
* | | |Others = Reserved.
|
|
* |[22:20] |TMR3SEL |TIMER3 Clock Source Selection
|
|
* | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT).
|
|
* | | |001 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT).
|
|
* | | |010 = Clock source from PCLK1.
|
|
* | | |011 = Clock source from external clock T3 pin.
|
|
* | | |101 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC).
|
|
* | | |111 = Clock source from 48 MHz internal high speed RC oscillator (HIRC).
|
|
* | | |Others = Reserved.
|
|
* |[26:24] |UART0SEL |UART0 Clock Source Selection
|
|
* | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT).
|
|
* | | |001 = Clock source from PLL.
|
|
* | | |010 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT).
|
|
* | | |011 = Clock source from 48 MHz internal high speed RC oscillator (HIRC).
|
|
* | | |100= PCLK0-> default.
|
|
* | | |101= LIRC
|
|
* |[30:28] |UART1SEL |UART1 Clock Source Selection
|
|
* | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT).
|
|
* | | |001 = Clock source from PLL.
|
|
* | | |010 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT).
|
|
* | | |011 = Clock source from 48 MHz internal high speed RC oscillator (HIRC).
|
|
* | | |100= PCLK1 -> default.
|
|
* | | |101= LIRC
|
|
* @var CLK_T::CLKSEL2
|
|
* Offset: 0x18 Clock Source Select Control Register 2
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[0] |PWM0SEL |PWM0 Clock Source Selection
|
|
* | | |The peripheral clock source of PWM0 is defined by PWM0SEL.
|
|
* | | |0 = Clock source from PLL.
|
|
* | | |1 = Clock source from PCLK0.
|
|
* |[1] |PWM1SEL |PWM1 Clock Source Selection
|
|
* | | |The peripheral clock source of PWM1 is defined by PWM1SEL.
|
|
* | | |0 = Clock source from PLL.
|
|
* | | |1 = Clock source from PCLK1.
|
|
* |[3:2] |QSPI0SEL |QSPI0 Clock Source Selection
|
|
* | | |00 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT).
|
|
* | | |01 = Clock source from PLL.
|
|
* | | |10 = Clock source from PCLK0.
|
|
* | | |11 = Clock source from 48 MHz internal high speed RC oscillator (HIRC).
|
|
* |[5:4] |SPI0SEL |SPI0 Clock Source Selection
|
|
* | | |00 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT).
|
|
* | | |01 = Clock source from PLL.
|
|
* | | |10 = Clock source from PCLK1.
|
|
* | | |11 = Clock source from 48 MHz internal high speed RC oscillator (HIRC).
|
|
* |[8] |BPWM0SEL |BPWM0 Clock Source Selection
|
|
* | | |The peripheral clock source of BPWM0 is defined by BPWM0SEL.
|
|
* | | |0 = Clock source from PLL.
|
|
* | | |1 = Clock source from PCLK0.
|
|
* |[9] |BPWM1SEL |BPWM1 Clock Source Selection
|
|
* | | |The peripheral clock source of BPWM1 is defined by BPWM1SEL.
|
|
* | | |0 = Clock source from PLL.
|
|
* | | |1 = Clock source from PCLK1.
|
|
* |[30:28] |PSIOSEL |PSIO Clock Source Selection
|
|
* | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT).
|
|
* | | |001 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT).
|
|
* | | |010 = Clock source from PCLK1.
|
|
* | | |011 = Clock source from PLL.
|
|
* | | |100 = Clock source from 38.4 kHz internal low speed RC oscillator (LIRC).
|
|
* | | |111 = Clock source from 48 MHz internal high speed RC oscillator (HIRC).
|
|
* | | |Others = Reserved.
|
|
* @var CLK_T::CLKSEL3
|
|
* Offset: 0x1C Clock Source Select Control Register 3
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[1:0] |SC0SEL |SC0 Clock Source Selection
|
|
* | | |00 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT).
|
|
* | | |01 = Clock source from PLL.
|
|
* | | |10 = Clock source from PCLK0.
|
|
* | | |11 = Clock source from 48 MHz internal high speed RC oscillator (HIRC).
|
|
* |[26:24] |UART2SEL |UART2 Clock Source Selection
|
|
* | | |000 = Clock source from 4~32 MHz external high speed crystal oscillator (HXT).
|
|
* | | |001 = Clock source from PLL.
|
|
* | | |010 = Reserved.
|
|
* | | |010 = Clock source from 32.768 kHz external low speed crystal oscillator (LXT).
|
|
* | | |011 = Clock source from 48 MHz internal high speed RC oscillator (HIRC).
|
|
* | | |100= PCLK 0-> default.
|
|
* | | |101= LIRC
|
|
* @var CLK_T::CLKDIV0
|
|
* Offset: 0x20 Clock Divider Number Register 0
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[3:0] |HCLKDIV |HCLK Clock Divide Number From HCLK Clock Source
|
|
* | | |HCLK clock frequency = (HCLK clock source frequency) / (HCLKDIV + 1).
|
|
* |[7:4] |USBDIV |USB Clock Divide Number From PLL Clock
|
|
* | | |USB clock frequency = (PLL frequency) / (USBDIV + 1).
|
|
* |[11:8] |UART0DIV |UART0 Clock Divide Number From UART0 Clock Source
|
|
* | | |UART0 clock frequency = (UART0 clock source frequency) / (UART0DIV + 1).
|
|
* |[15:12] |UART1DIV |UART1 Clock Divide Number From UART1 Clock Source
|
|
* | | |UART1 clock frequency = (UART1 clock source frequency) / (UART1DIV + 1).
|
|
* |[23:16] |EADCDIV |EADC Clock Divide Number From EADC Clock Source
|
|
* | | |EADC clock frequency = (EADC clock source frequency) / (EADCDIV + 1).
|
|
* @var CLK_T::CLKDIV1
|
|
* Offset: 0x24 Clock Divider Number Register 1
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[7:0] |SC0DIV |SC0 Clock Divide Number From SC0 Clock Source
|
|
* | | |SC0 clock frequency = (SC0 clock source frequency ) / (SC0DIV + 1).
|
|
* |[31:24] |PSIODIV |PSIO Clock Divide Number From PSIO Clock Source
|
|
* | | |PSIO clock frequency = (PSIO clock source frequency ) / (PSIODIV + 1).
|
|
* @var CLK_T::CLKDIV4
|
|
* Offset: 0x30 Clock Divider Number Register 4
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[3:0] |UART2DIV |UART2 Clock Divide Number From UART2 Clock Source
|
|
* | | |UART2 clock frequency = (UART2 clock source frequency) / (UART2DIV + 1).
|
|
* @var CLK_T::PCLKDIV
|
|
* Offset: 0x34 APB Clock Divider Register
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[2:0] |APB0DIV |APB0 Clock DIvider
|
|
* | | |APB0 clock can be divided from HCLK
|
|
* | | |000: PCLK0 = HCLK.
|
|
* | | |001: PCLK0 = 1/2 HCLK.
|
|
* | | |010: PCLK0 = 1/4 HCLK.
|
|
* | | |011: PCLK0 = 1/8 HCLK.
|
|
* | | |100: PCLK0 = 1/16 HCLK.
|
|
* | | |101: PCLK0 = 1/32 HCLK.
|
|
* | | |Others: Reserved.
|
|
* |[6:4] |APB1DIV |APB1 Clock DIvider
|
|
* | | |APB1 clock can be divided from HCLK
|
|
* | | |000: PCLK1 = HCLK.
|
|
* | | |001: PCLK1 = 1/2 HCLK.
|
|
* | | |010: PCLK1 = 1/4 HCLK.
|
|
* | | |011: PCLK1 = 1/8 HCLK.
|
|
* | | |100: PCLK1 = 1/16 HCLK.
|
|
* | | |101: PCLK1 = 1/32 HCLK.
|
|
* | | |Others: Reserved.
|
|
* @var CLK_T::PLLCTL
|
|
* Offset: 0x40 PLL Control Register
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[5:0] |FBDIV |PLL Feedback Divider Control (Write Protect)
|
|
* | | |Refer to the formulas below the table.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[12:9] |INDIV |PLL Input Divider Control (Write Protect)
|
|
* | | |Refer to the formulas below the table.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[15:14] |OUTDIV |PLL Output Divider Control (Write Protect)
|
|
* | | |Refer to the formulas below the table.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[16] |PD |Power-down Mode (Write Protect)
|
|
* | | |If set the PDEN bit to 1 in CLK_PWRCTL register, the PLL will enter Power-down mode, too.
|
|
* | | |0 = PLL is in normal mode.
|
|
* | | |1 = PLL is in Power-down mode (default).
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[17] |BP |PLL Bypass Control (Write Protect)
|
|
* | | |0 = PLL is in normal mode (default).
|
|
* | | |1 = PLL clock output is same as PLL input clock FIN.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[18] |OE |PLL OE (FOUT Enable) Pin Control (Write Protect)
|
|
* | | |0 = PLL FOUT Enabled.
|
|
* | | |1 = PLL FOUT is fixed low.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[20:19] |PLLSRC |PLL Source Clock Selection (Write Protect)
|
|
* | | |00 = PLL source clock from 4~32 MHz external high-speed crystal oscillator (HXT).
|
|
* | | |01 = PLL source clock from 12 MHz internal high-speed oscillator (HIRC/4).
|
|
* | | |10 = PLL source clock from 4~32 MHz external high-speed crystal oscillator (HXT).
|
|
* | | |11 = PLL source clock from 4 MHz internal high-speed oscillator (MIRC).
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* | | |Note: MIRC and HIRC have to be both on when source switch between them
|
|
* |[23] |STBSEL |PLL Stable Counter Selection (Write Protect)
|
|
* | | |0 = PLL stable time is 1200 PLL source clock (suitable for source clock is equal to or less than 12 MHz).
|
|
* | | |1 = PLL stable time is 2400 PLL source clock (suitable for source clock is larger than 12 MHz).
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[24] |PLL_CLF_EN|1: PLL Clock Filter On
|
|
* | | |0 : OFF
|
|
* @var CLK_T::STATUS
|
|
* Offset: 0x50 Clock Status Monitor Register
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[0] |HXTSTB |HXT Clock Source Stable Flag (Read Only)
|
|
* | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock is not stable or disabled.
|
|
* | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock is stable and enabled.
|
|
* |[1] |LXTSTB |LXT Clock Source Stable Flag (Read Only)
|
|
* | | |0 = 32.768 kHz external low speed crystal oscillator (LXT) clock is not stable or disabled.
|
|
* | | |1 = 32.768 kHz external low speed crystal oscillator (LXT) clock is stabled and enabled.
|
|
* |[2] |PLLSTB |Internal PLL Clock Source Stable Flag (Read Only)
|
|
* | | |0 = Internal PLL clock is not stable or disabled.
|
|
* | | |1 = Internal PLL clock is stable and enabled.
|
|
* |[3] |LIRCSTB |LIRC Clock Source Stable Flag (Read Only)
|
|
* | | |0 = 38.4 kHz internal low speed RC oscillator (LIRC) clock is not stable or disabled.
|
|
* | | |1 = 38.4 kHz internal low speed RC oscillator (LIRC) clock is stable and enabled.
|
|
* |[4] |HIRCSTB |HIRC Clock Source Stable Flag (Read Only)
|
|
* | | |0 = 48 MHz internal high speed RC oscillator (HIRC) clock is not stable or disabled.
|
|
* | | |1 = 48 MHz internal high speed RC oscillator (HIRC) clock is stable and enabled.
|
|
* |[6] |MIRCSTB |MIRC Clock Source Stable Flag (Read Only)
|
|
* | | |0 = 4 MHz internal mid speed RC oscillator (MIRC) clock is not stable or disabled.
|
|
* | | |1 = 4 MHz internal mid speed RC oscillator (MIRC) clock is stable and enabled.
|
|
* |[7] |CLKSFAIL |Clock Switching Fail Flag (Read Only)
|
|
* | | |This bit is updated when software switches system clock source
|
|
* | | |If switch target clock is stable, this bit will be set to 0
|
|
* | | |If switch target clock is not stable, this bit will be set to 1.
|
|
* | | |0 = Clock switching success.
|
|
* | | |1 = Clock switching failure.
|
|
* | | |Note: Write 1 to clear the bit to 0.
|
|
* @var CLK_T::CLKOCTL
|
|
* Offset: 0x60 Clock Output Control Register
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[3:0] |FREQSEL |Clock Output Frequency Selection
|
|
* | | |The formula of output frequency is
|
|
* | | |Fout = Fin/2(N+1).
|
|
* | | |Fin is the input clock frequency.
|
|
* | | |Fout is the frequency of divider output clock.
|
|
* | | |N is the 4-bit value of FREQSEL[3:0].
|
|
* |[4] |CLKOEN |Clock Output Enable Bit
|
|
* | | |0 = Clock Output function Disabled.
|
|
* | | |1 = Clock Output function Enabled.
|
|
* |[5] |DIV1EN |Clock Output Divide One Enable Bit
|
|
* | | |0 = Clock Output will output clock with source frequency divided by FREQSEL.
|
|
* | | |1 = Clock Output will output clock with source frequency.
|
|
* |[6] |CLK1HZEN |Clock Output 1Hz Enable Bit
|
|
* | | |0 = 1 Hz clock output for 32.768 kHz frequency compensation Disabled.
|
|
* | | |1 = 1 Hz clock output for 32.768 kHz frequency compensation Enabled.
|
|
* @var CLK_T::CLKDCTL
|
|
* Offset: 0x70 Clock Fail Detector Control Register
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[4] |HXTFDEN |HXT Clock Fail Detector Enable Bit
|
|
* | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock fail detector Disabled.
|
|
* | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock fail detector Enabled.
|
|
* |[5] |HXTFIEN |HXT Clock Fail Interrupt Enable Bit
|
|
* | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock fail interrupt Disabled.
|
|
* | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock fail interrupt Enabled.
|
|
* |[12] |LXTFDEN |LXT Clock Fail Detector Enable Bit
|
|
* | | |0 = 32.768 kHz external low speed crystal oscillator (LXT) clock fail detector Disabled.
|
|
* | | |1 = 32.768 kHz external low speed crystal oscillator (LXT) clock fail detector Enabled.
|
|
* |[13] |LXTFIEN |LXT Clock Fail Interrupt Enable Bit
|
|
* | | |0 = 32.768 kHz external low speed crystal oscillator (LXT) clock fail interrupt Disabled.
|
|
* | | |1 = 32.768 kHz external low speed crystal oscillator (LXT) clock fail interrupt Enabled.
|
|
* |[16] |HXTFQDEN |HXT Clock Frequency Range Detector Enable Bit
|
|
* | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock frequency range detector Disabled.
|
|
* | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock frequency range detector Enabled.
|
|
* |[17] |HXTFQIEN |HXT Clock Frequency Range Detector Interrupt Enable Bit
|
|
* | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock frequency range detector fail interrupt Disabled.
|
|
* | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock frequency range detector fail interrupt Enabled.
|
|
* @var CLK_T::CLKDSTS
|
|
* Offset: 0x74 Clock Fail Detector Status Register
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[0] |HXTFIF |HXT Clock Fail Interrupt Flag (Write Protect)
|
|
* | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock is normal.
|
|
* | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock stops.
|
|
* | | |Note: Write 1 to clear the bit to 0.
|
|
* |[1] |LXTFIF |LXT Clock Fail Interrupt Flag (Write Protect)
|
|
* | | |0 = 32.768 kHz external low speed crystal oscillator (LXT) clock is normal.
|
|
* | | |1 = 32.768 kHz external low speed crystal oscillator (LXT) stops.
|
|
* | | |Note: Write 1 to clear the bit to 0.
|
|
* |[8] |HXTFQIF |HXT Clock Frequency Range Detector Interrupt Flag (Write Protect)
|
|
* | | |0 = 4~32 MHz external high speed crystal oscillator (HXT) clock frequency is normal.
|
|
* | | |1 = 4~32 MHz external high speed crystal oscillator (HXT) clock frequency is abnormal.
|
|
* | | |Note: Write 1 to clear the bit to 0.
|
|
* @var CLK_T::CDUPB
|
|
* Offset: 0x78 Clock Frequency Range Detector Upper Boundary Register
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[9:0] |UPERBD |HXT Clock Frequency Range Detector Upper Boundary Value
|
|
* | | |The bits define the maximum value of frequency range detector window.
|
|
* | | |When HXT frequency higher than this maximum frequency value, the HXT Clock Frequency Range Detector Interrupt Flag will set to 1.
|
|
* @var CLK_T::CDLOWB
|
|
* Offset: 0x7C Clock Frequency Range Detector Lower Boundary Register
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[9:0] |LOWERBD |HXT Clock Frequency Range Detector Lower Boundary Value
|
|
* | | |The bits define the minimum value of frequency range detector window.
|
|
* | | |When HXT frequency lower than this minimum frequency value, the HXT Clock Frequency Range Detector Interrupt Flag will set to 1.
|
|
* @var CLK_T::PMUCTL
|
|
* Offset: 0x90 Power Manager Control Register
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[2:0] |PDMSEL |Power-down Mode Selection (Write Protect)
|
|
* | | |This is a protected register. Please refer to open lock sequence to program it.
|
|
* | | |These bits control chip power-down mode grade selection when CPU execute WFI/WFE instruction.
|
|
* | | |000 = Power-down mode is selected. (PD)
|
|
* | | |010 = fast wake up.(FWPD)
|
|
* | | |110 = Deep Power-down mode is selected (DPD).
|
|
* | | |others = Reserved.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[8] |WKTMREN |Wake-up Timer Enable (Write Protect)
|
|
* | | |This is a protected register. Please refer to open lock sequence to program it.
|
|
* | | |0 = Wake-up timer disable at DPD mode.
|
|
* | | |1 = Wake-up timer enabled at DPD mode.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[11:9] |WKTMRIS |Wake-up Timer Time-out Interval Select (Write Protect)
|
|
* | | |This is a protected register. Please refer to open lock sequence to program it.
|
|
* | | |These bits control wake-up timer time-out interval when chip at DPD mode.
|
|
* | | |000 = Time-out interval is 128 OSC32K clocks (~3.368 ms).
|
|
* | | |001 = Time-out interval is 256 OSC32K clocks (~6.736 ms).
|
|
* | | |010 = Time-out interval is 512 OSC32K clocks (~13.47 ms).
|
|
* | | |011 = Time-out interval is 1024 OSC32K clocks (~26.95 ms).
|
|
* | | |100 = Time-out interval is 4096 OSC32K clocks (~107.79 ms).
|
|
* | | |101 = Time-out interval is 8192 OSC32K clocks (~215.58 ms).
|
|
* | | |110 = Time-out interval is 16384 OSC32K clocks (~431.16 ms).
|
|
* | | |111 = Time-out interval is 32768 OSC32K clocks (~862.32 ms).
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[17:16] |WKPINEN0 |Wake-up Pin Enable 0(Write Protect)
|
|
* | | |This is a protected register. Please refer to open lock sequence to program it.
|
|
* | | |This is control register for GPC.0 to wake-up pin.
|
|
* | | |00 = Wake-up pin disable at Deep Power-down mode.
|
|
* | | |01 = Wake-up pin rising edge enabled at Deep Power-down mode.
|
|
* | | |10 = Wake-up pin falling edge enabled at Deep Power-down mode.
|
|
* | | |11 = Wake-up pin both edge enabled at Deep Power-down mode.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[22] |WKPINDBEN |Wake-up pin De-bounce Enable Bit (Write Protect)
|
|
* | | |The WKPINDBEN bit is used to enable the de-bounce function for wake-up pin.
|
|
* | | |If the input signal pulse width cannot be sampled by continuous eight de-bounce sample cycle,
|
|
* | | |the input signal transition is seen as the signal bounce and will not trigger the wakeup.
|
|
* | | |The de-bounce clock source is the 38 kHz internal low speed RC oscillator (LIRC).
|
|
* | | |0 = Deep power-down wake-up pin De-bounce function disable.
|
|
* | | |1 = Deep power-down wake-up pin De-bounce function enable.
|
|
* | | |The de-bounce function is valid only for edge triggered
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[23] |RTCWKEN |RTC Wake-up Enable (Write Protect)
|
|
* | | |This is a protected register. Please refer to open lock sequence to program it.
|
|
* | | |0 = RTC wake-up disable at Deep Power-down mode or Standby Power-down mode.
|
|
* | | |1 = RTC wake-up enabled at Deep Power-down mode or Standby Power-down mode.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[25:24] |WKPINEN1 |Wake-up Pin Enable 1(Write Protect)
|
|
* | | |This is a protected register. Please refer to open lock sequence to program it.
|
|
* | | |This is control register for GPB.0 to wake-up pin.
|
|
* | | |00 = Wake-up pin disable at Deep Power-down mode.
|
|
* | | |01 = Wake-up pin rising edge enabled at Deep Power-down mode.
|
|
* | | |10 = Wake-up pin falling edge enabled at Deep Power-down mode.
|
|
* | | |11 = Wake-up pin both edge enabled at Deep Power-down mode.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register
|
|
* |[27:26] |WKPINEN2 |Wake-up Pin Enable 2(Write Protect)
|
|
* | | |This is a protected register. Please refer to open lock sequence to program it.
|
|
* | | |This is control register for GPB.2 to wake-up pin.
|
|
* | | |00 = Wake-up pin disable at Deep Power-down mode.
|
|
* | | |01 = Wake-up pin rising edge enabled at Deep Power-down mode.
|
|
* | | |10 = Wake-up pin falling edge enabled at Deep Power-down mode.
|
|
* | | |11 = Wake-up pin both edge enabled at Deep Power-down mode.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[29:28] |WKPINEN3 |Wake-up Pin Enable 3(Write Protect)
|
|
* | | |This is a protected register. Please refer to open lock sequence to program it.
|
|
* | | |This is control register for GPB.12 to wake-up pin.
|
|
* | | |00 = Wake-up pin disable at Deep Power-down mode.
|
|
* | | |01 = Wake-up pin rising edge enabled at Deep Power-down mode.
|
|
* | | |10 = Wake-up pin falling edge enabled at Deep Power-down mode.
|
|
* | | |11 = Wake-up pin both edge enabled at Deep Power-down mode.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* |[31:30] |WKPINEN4 |Wake-up Pin Enable 4(Write Protect)
|
|
* | | |This is a protected register. Please refer to open lock sequence to program it.
|
|
* | | |This is control register for GPF.6 to wake-up pin.
|
|
* | | |00 = Wake-up pin disable at Deep Power-down mode.
|
|
* | | |01 = Wake-up pin rising edge enabled at Deep Power-down mode.
|
|
* | | |10 = Wake-up pin falling edge enabled at Deep Power-down mode.
|
|
* | | |11 = Wake-up pin both edge enabled at Deep Power-down mode.
|
|
* | | |Note: This bit is write protected. Refer to the SYS_REGLCTL register.
|
|
* @var CLK_T::PMUSTS
|
|
* Offset: 0x94 Power Manager Status Register
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[0] |PINWK0 |Pin Wake-up Flag (Read Only)
|
|
* | | |This flag indicates that wake-up of chip from Deep Power-down mode was requested by a transition of the WAKEUP pin (GPC.0)
|
|
* | | |This flag is cleared when DPD mode is entered.
|
|
* |[1] |TMRWK |Timer Wake-up Flag (Read Only)
|
|
* | | |This flag indicates that wake-up of chip from Deep Power-down mode (DPD) was requested by wakeup timer time-out
|
|
* | | |This flag is cleared when DPD mode is entered.
|
|
* |[2] |RTCWK |RTC Wake-up Flag (Read Only)
|
|
* | | |This flag indicates that wakeup of device from Deep Power-down mode (DPD) was requested with a RTC alarm, tick time or tamper happened
|
|
* | | |This flag is cleared when DPD mode is entered.
|
|
* |[3] |PINWK1 |Pin Wake-up Flag (Read Only)
|
|
* | | |This flag indicates that wake-up of chip from Deep Power-down mode was requested by a transition of the WAKEUP pin (GPB.0)
|
|
* | | |This flag is cleared when DPD mode is entered.
|
|
* |[4] |PINWK2 |Pin Wake-up Flag (Read Only)
|
|
* | | |This flag indicates that wake-up of chip from Deep Power-down mode was requested by a transition of the WAKEUP pin (GPB.2)
|
|
* | | |This flag is cleared when DPD mode is entered.
|
|
* |[5] |PINWK3 |Pin Wake-up Flag (Read Only)
|
|
* | | |This flag indicates that wake-up of chip from Deep Power-down mode was requested by a transition of the WAKEUP pin (GPB.12)
|
|
* | | |This flag is cleared when DPD mode is entered.
|
|
* |[6] |PINWK4 |Pin Wake-up Flag (Read Only)
|
|
* | | |This flag indicates that wake-up of chip from Deep Power-down mode was requested by a transition of the WAKEUP pin (GPF.6)
|
|
* | | |This flag is cleared when DPD mode is entered.
|
|
* |[12] |LVRWK |LVR Wake-up Flag (Read Only)
|
|
* | | |This flag indicates that wakeup of device from Deep Power-down mode was requested with a LVR happened
|
|
* | | |This flag is cleared when DPD mode is entered.
|
|
* |[31] |CLRWK |Clear Wake-up Flag
|
|
* | | |0 = No clear.
|
|
* | | |1= Clear all wake-up flag.
|
|
* @var CLK_T::HXTFSEL
|
|
* Offset: 0xB4 HXT Filter Select Control Register
|
|
* ---------------------------------------------------------------------------------------------------
|
|
* |Bits |Field |Descriptions
|
|
* | :----: | :----: | :---- |
|
|
* |[0] |HXTFSEL |HXT Filter Select (Write Protect)
|
|
* | | |0 = HXT frequency is > 12MHz.
|
|
* | | |1 = HXT frequency is <= 12MHz.
|
|
*/
|
|
__IO uint32_t PWRCTL; /*!< [0x0000] System Power-down Control Register */
|
|
__IO uint32_t AHBCLK; /*!< [0x0004] AHB Devices Clock Enable Control Register */
|
|
__IO uint32_t APBCLK0; /*!< [0x0008] APB Devices Clock Enable Control Register 0 */
|
|
__IO uint32_t APBCLK1; /*!< [0x000c] APB Devices Clock Enable Control Register 1 */
|
|
__IO uint32_t CLKSEL0; /*!< [0x0010] Clock Source Select Control Register 0 */
|
|
__IO uint32_t CLKSEL1; /*!< [0x0014] Clock Source Select Control Register 1 */
|
|
__IO uint32_t CLKSEL2; /*!< [0x0018] Clock Source Select Control Register 2 */
|
|
__IO uint32_t CLKSEL3; /*!< [0x001c] Clock Source Select Control Register 3 */
|
|
__IO uint32_t CLKDIV0; /*!< [0x0020] Clock Divider Number Register 0 */
|
|
__IO uint32_t CLKDIV1; /*!< [0x0024] Clock Divider Number Register 1 */
|
|
/// @cond HIDDEN_SYMBOLS
|
|
__I uint32_t RESERVE0[2];
|
|
/// @endcond //HIDDEN_SYMBOLS
|
|
__IO uint32_t CLKDIV4; /*!< [0x0030] Clock Divider Number Register 4 */
|
|
__IO uint32_t PCLKDIV; /*!< [0x0034] APB Clock Divider Register */
|
|
/// @cond HIDDEN_SYMBOLS
|
|
__I uint32_t RESERVE1[2];
|
|
/// @endcond //HIDDEN_SYMBOLS
|
|
__IO uint32_t PLLCTL; /*!< [0x0040] PLL Control Register */
|
|
/// @cond HIDDEN_SYMBOLS
|
|
__I uint32_t RESERVE2[3];
|
|
/// @endcond //HIDDEN_SYMBOLS
|
|
__I uint32_t STATUS; /*!< [0x0050] Clock Status Monitor Register */
|
|
/// @cond HIDDEN_SYMBOLS
|
|
__I uint32_t RESERVE3[3];
|
|
/// @endcond //HIDDEN_SYMBOLS
|
|
__IO uint32_t CLKOCTL; /*!< [0x0060] Clock Output Control Register */
|
|
/// @cond HIDDEN_SYMBOLS
|
|
__I uint32_t RESERVE4[3];
|
|
/// @endcond //HIDDEN_SYMBOLS
|
|
__IO uint32_t CLKDCTL; /*!< [0x0070] Clock Fail Detector Control Register */
|
|
__IO uint32_t CLKDSTS; /*!< [0x0074] Clock Fail Detector Status Register */
|
|
__IO uint32_t CDUPB; /*!< [0x0078] Clock Frequency Range Detector Upper Boundary Register */
|
|
__IO uint32_t CDLOWB; /*!< [0x007c] Clock Frequency Range Detector Lower Boundary Register */
|
|
/// @cond HIDDEN_SYMBOLS
|
|
__I uint32_t RESERVE5[4];
|
|
/// @endcond //HIDDEN_SYMBOLS
|
|
__IO uint32_t PMUCTL; /*!< [0x0090] Power Manager Control Register */
|
|
__IO uint32_t PMUSTS; /*!< [0x0094] Power Manager Status Register */
|
|
/// @cond HIDDEN_SYMBOLS
|
|
__I uint32_t RESERVE6[7];
|
|
/// @endcond //HIDDEN_SYMBOLS
|
|
__IO uint32_t HXTFSEL; /*!< [0x00b4] HXT Filter Select Control Register */
|
|
} CLK_T;
|
|
|
|
/**
|
|
@addtogroup CLK_CONST CLK Bit Field Definition
|
|
Constant Definitions for CLK Controller
|
|
@{ */
|
|
|
|
#define CLK_PWRCTL_HXTEN_Pos (0) /*!< CLK_T::PWRCTL: HXTEN Position */
|
|
#define CLK_PWRCTL_HXTEN_Msk (0x1ul << CLK_PWRCTL_HXTEN_Pos) /*!< CLK_T::PWRCTL: HXTEN Mask */
|
|
|
|
#define CLK_PWRCTL_LXTEN_Pos (1) /*!< CLK_T::PWRCTL: LXTEN Position */
|
|
#define CLK_PWRCTL_LXTEN_Msk (0x1ul << CLK_PWRCTL_LXTEN_Pos) /*!< CLK_T::PWRCTL: LXTEN Mask */
|
|
|
|
#define CLK_PWRCTL_HIRCEN_Pos (2) /*!< CLK_T::PWRCTL: HIRCEN Position */
|
|
#define CLK_PWRCTL_HIRCEN_Msk (0x1ul << CLK_PWRCTL_HIRCEN_Pos) /*!< CLK_T::PWRCTL: HIRCEN Mask */
|
|
|
|
#define CLK_PWRCTL_LIRCEN_Pos (3) /*!< CLK_T::PWRCTL: LIRCEN Position */
|
|
#define CLK_PWRCTL_LIRCEN_Msk (0x1ul << CLK_PWRCTL_LIRCEN_Pos) /*!< CLK_T::PWRCTL: LIRCEN Mask */
|
|
|
|
#define CLK_PWRCTL_PDWKDLY_Pos (4) /*!< CLK_T::PWRCTL: PDWKDLY Position */
|
|
#define CLK_PWRCTL_PDWKDLY_Msk (0x1ul << CLK_PWRCTL_PDWKDLY_Pos) /*!< CLK_T::PWRCTL: PDWKDLY Mask */
|
|
|
|
#define CLK_PWRCTL_PDWKIEN_Pos (5) /*!< CLK_T::PWRCTL: PDWKIEN Position */
|
|
#define CLK_PWRCTL_PDWKIEN_Msk (0x1ul << CLK_PWRCTL_PDWKIEN_Pos) /*!< CLK_T::PWRCTL: PDWKIEN Mask */
|
|
|
|
#define CLK_PWRCTL_PDWKIF_Pos (6) /*!< CLK_T::PWRCTL: PDWKIF Position */
|
|
#define CLK_PWRCTL_PDWKIF_Msk (0x1ul << CLK_PWRCTL_PDWKIF_Pos) /*!< CLK_T::PWRCTL: PDWKIF Mask */
|
|
|
|
#define CLK_PWRCTL_PDEN_Pos (7) /*!< CLK_T::PWRCTL: PDEN Position */
|
|
#define CLK_PWRCTL_PDEN_Msk (0x1ul << CLK_PWRCTL_PDEN_Pos) /*!< CLK_T::PWRCTL: PDEN Mask */
|
|
|
|
#define CLK_PWRCTL_MIRCEN_Pos (19) /*!< CLK_T::PWRCTL: MIRCEN Position */
|
|
#define CLK_PWRCTL_MIRCEN_Msk (0x1ul << CLK_PWRCTL_MIRCEN_Pos) /*!< CLK_T::PWRCTL: MIRCEN Mask */
|
|
|
|
#define CLK_PWRCTL_HXTGAIN_Pos (20) /*!< CLK_T::PWRCTL: HXTGAIN Position */
|
|
#define CLK_PWRCTL_HXTGAIN_Msk (0x7ul << CLK_PWRCTL_HXTGAIN_Pos) /*!< CLK_T::PWRCTL: HXTGAIN Mask */
|
|
|
|
#define CLK_AHBCLK_PDMACKEN_Pos (1) /*!< CLK_T::AHBCLK: PDMACKEN Position */
|
|
#define CLK_AHBCLK_PDMACKEN_Msk (0x1ul << CLK_AHBCLK_PDMACKEN_Pos) /*!< CLK_T::AHBCLK: PDMACKEN Mask */
|
|
|
|
#define CLK_AHBCLK_ISPCKEN_Pos (2) /*!< CLK_T::AHBCLK: ISPCKEN Position */
|
|
#define CLK_AHBCLK_ISPCKEN_Msk (0x1ul << CLK_AHBCLK_ISPCKEN_Pos) /*!< CLK_T::AHBCLK: ISPCKEN Mask */
|
|
|
|
#define CLK_AHBCLK_EBICKEN_Pos (3) /*!< CLK_T::AHBCLK: EBICKEN Position */
|
|
#define CLK_AHBCLK_EBICKEN_Msk (0x1ul << CLK_AHBCLK_EBICKEN_Pos) /*!< CLK_T::AHBCLK: EBICKEN Mask */
|
|
|
|
#define CLK_AHBCLK_EXSTCKEN_Pos (4) /*!< CLK_T::AHBCLK: EXSTCKEN Position */
|
|
#define CLK_AHBCLK_EXSTCKEN_Msk (0x1ul << CLK_AHBCLK_EXSTCKEN_Pos) /*!< CLK_T::AHBCLK: EXSTCKEN Mask */
|
|
|
|
#define CLK_AHBCLK_CRCCKEN_Pos (7) /*!< CLK_T::AHBCLK: CRCCKEN Position */
|
|
#define CLK_AHBCLK_CRCCKEN_Msk (0x1ul << CLK_AHBCLK_CRCCKEN_Pos) /*!< CLK_T::AHBCLK: CRCCKEN Mask */
|
|
|
|
#define CLK_AHBCLK_CRPTCKEN_Pos (12) /*!< CLK_T::AHBCLK: CRPTCKEN Position */
|
|
#define CLK_AHBCLK_CRPTCKEN_Msk (0x1ul << CLK_AHBCLK_CRPTCKEN_Pos) /*!< CLK_T::AHBCLK: CRPTCKEN Mask */
|
|
|
|
#define CLK_AHBCLK_FMCIDLE_Pos (15) /*!< CLK_T::AHBCLK: FMCIDLE Position */
|
|
#define CLK_AHBCLK_FMCIDLE_Msk (0x1ul << CLK_AHBCLK_FMCIDLE_Pos) /*!< CLK_T::AHBCLK: FMCIDLE Mask */
|
|
|
|
#define CLK_AHBCLK_GPACKEN_Pos (24) /*!< CLK_T::AHBCLK: GPACKEN Position */
|
|
#define CLK_AHBCLK_GPACKEN_Msk (0x1ul << CLK_AHBCLK_GPACKEN_Pos) /*!< CLK_T::AHBCLK: GPACKEN Mask */
|
|
|
|
#define CLK_AHBCLK_GPBCKEN_Pos (25) /*!< CLK_T::AHBCLK: GPBCKEN Position */
|
|
#define CLK_AHBCLK_GPBCKEN_Msk (0x1ul << CLK_AHBCLK_GPBCKEN_Pos) /*!< CLK_T::AHBCLK: GPBCKEN Mask */
|
|
|
|
#define CLK_AHBCLK_GPCCKEN_Pos (26) /*!< CLK_T::AHBCLK: GPCCKEN Position */
|
|
#define CLK_AHBCLK_GPCCKEN_Msk (0x1ul << CLK_AHBCLK_GPCCKEN_Pos) /*!< CLK_T::AHBCLK: GPCCKEN Mask */
|
|
|
|
#define CLK_AHBCLK_GPDCKEN_Pos (27) /*!< CLK_T::AHBCLK: GPDCKEN Position */
|
|
#define CLK_AHBCLK_GPDCKEN_Msk (0x1ul << CLK_AHBCLK_GPDCKEN_Pos) /*!< CLK_T::AHBCLK: GPDCKEN Mask */
|
|
|
|
#define CLK_AHBCLK_GPECKEN_Pos (28) /*!< CLK_T::AHBCLK: GPECKEN Position */
|
|
#define CLK_AHBCLK_GPECKEN_Msk (0x1ul << CLK_AHBCLK_GPECKEN_Pos) /*!< CLK_T::AHBCLK: GPECKEN Mask */
|
|
|
|
#define CLK_AHBCLK_GPFCKEN_Pos (29) /*!< CLK_T::AHBCLK: GPFCKEN Position */
|
|
#define CLK_AHBCLK_GPFCKEN_Msk (0x1ul << CLK_AHBCLK_GPFCKEN_Pos) /*!< CLK_T::AHBCLK: GPFCKEN Mask */
|
|
|
|
#define CLK_APBCLK0_WDTCKEN_Pos (0) /*!< CLK_T::APBCLK0: WDTCKEN Position */
|
|
#define CLK_APBCLK0_WDTCKEN_Msk (0x1ul << CLK_APBCLK0_WDTCKEN_Pos) /*!< CLK_T::APBCLK0: WDTCKEN Mask */
|
|
|
|
#define CLK_APBCLK0_RTCCKEN_Pos (1) /*!< CLK_T::APBCLK0: RTCCKEN Position */
|
|
#define CLK_APBCLK0_RTCCKEN_Msk (0x1ul << CLK_APBCLK0_RTCCKEN_Pos) /*!< CLK_T::APBCLK0: RTCCKEN Mask */
|
|
|
|
#define CLK_APBCLK0_TMR0CKEN_Pos (2) /*!< CLK_T::APBCLK0: TMR0CKEN Position */
|
|
#define CLK_APBCLK0_TMR0CKEN_Msk (0x1ul << CLK_APBCLK0_TMR0CKEN_Pos) /*!< CLK_T::APBCLK0: TMR0CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_TMR1CKEN_Pos (3) /*!< CLK_T::APBCLK0: TMR1CKEN Position */
|
|
#define CLK_APBCLK0_TMR1CKEN_Msk (0x1ul << CLK_APBCLK0_TMR1CKEN_Pos) /*!< CLK_T::APBCLK0: TMR1CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_TMR2CKEN_Pos (4) /*!< CLK_T::APBCLK0: TMR2CKEN Position */
|
|
#define CLK_APBCLK0_TMR2CKEN_Msk (0x1ul << CLK_APBCLK0_TMR2CKEN_Pos) /*!< CLK_T::APBCLK0: TMR2CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_TMR3CKEN_Pos (5) /*!< CLK_T::APBCLK0: TMR3CKEN Position */
|
|
#define CLK_APBCLK0_TMR3CKEN_Msk (0x1ul << CLK_APBCLK0_TMR3CKEN_Pos) /*!< CLK_T::APBCLK0: TMR3CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_CLKOCKEN_Pos (6) /*!< CLK_T::APBCLK0: CLKOCKEN Position */
|
|
#define CLK_APBCLK0_CLKOCKEN_Msk (0x1ul << CLK_APBCLK0_CLKOCKEN_Pos) /*!< CLK_T::APBCLK0: CLKOCKEN Mask */
|
|
|
|
#define CLK_APBCLK0_ACMP01CKEN_Pos (7) /*!< CLK_T::APBCLK0: ACMP01CKEN Position */
|
|
#define CLK_APBCLK0_ACMP01CKEN_Msk (0x1ul << CLK_APBCLK0_ACMP01CKEN_Pos) /*!< CLK_T::APBCLK0: ACMP01CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_I2C0CKEN_Pos (8) /*!< CLK_T::APBCLK0: I2C0CKEN Position */
|
|
#define CLK_APBCLK0_I2C0CKEN_Msk (0x1ul << CLK_APBCLK0_I2C0CKEN_Pos) /*!< CLK_T::APBCLK0: I2C0CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_I2C1CKEN_Pos (9) /*!< CLK_T::APBCLK0: I2C1CKEN Position */
|
|
#define CLK_APBCLK0_I2C1CKEN_Msk (0x1ul << CLK_APBCLK0_I2C1CKEN_Pos) /*!< CLK_T::APBCLK0: I2C1CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_QSPI0CKEN_Pos (12) /*!< CLK_T::APBCLK0: QSPI0CKEN Position */
|
|
#define CLK_APBCLK0_QSPI0CKEN_Msk (0x1ul << CLK_APBCLK0_QSPI0CKEN_Pos) /*!< CLK_T::APBCLK0: QSPI0CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_SPI0CKEN_Pos (13) /*!< CLK_T::APBCLK0: SPI0CKEN Position */
|
|
#define CLK_APBCLK0_SPI0CKEN_Msk (0x1ul << CLK_APBCLK0_SPI0CKEN_Pos) /*!< CLK_T::APBCLK0: SPI0CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_SPI1CKEN_Pos (14) /*!< CLK_T::APBCLK0: SPI1CKEN Position */
|
|
#define CLK_APBCLK0_SPI1CKEN_Msk (0x1ul << CLK_APBCLK0_SPI1CKEN_Pos) /*!< CLK_T::APBCLK0: SPI1CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_UART0CKEN_Pos (16) /*!< CLK_T::APBCLK0: UART0CKEN Position */
|
|
#define CLK_APBCLK0_UART0CKEN_Msk (0x1ul << CLK_APBCLK0_UART0CKEN_Pos) /*!< CLK_T::APBCLK0: UART0CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_UART1CKEN_Pos (17) /*!< CLK_T::APBCLK0: UART1CKEN Position */
|
|
#define CLK_APBCLK0_UART1CKEN_Msk (0x1ul << CLK_APBCLK0_UART1CKEN_Pos) /*!< CLK_T::APBCLK0: UART1CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_UART2CKEN_Pos (18) /*!< CLK_T::APBCLK0: UART2CKEN Position */
|
|
#define CLK_APBCLK0_UART2CKEN_Msk (0x1ul << CLK_APBCLK0_UART2CKEN_Pos) /*!< CLK_T::APBCLK0: UART2CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_UART3CKEN_Pos (19) /*!< CLK_T::APBCLK0: UART3CKEN Position */
|
|
#define CLK_APBCLK0_UART3CKEN_Msk (0x1ul << CLK_APBCLK0_UART3CKEN_Pos) /*!< CLK_T::APBCLK0: UART3CKEN Mask */
|
|
|
|
#define CLK_APBCLK0_USBDCKEN_Pos (27) /*!< CLK_T::APBCLK0: USBDCKEN Position */
|
|
#define CLK_APBCLK0_USBDCKEN_Msk (0x1ul << CLK_APBCLK0_USBDCKEN_Pos) /*!< CLK_T::APBCLK0: USBDCKEN Mask */
|
|
|
|
#define CLK_APBCLK0_EADCCKEN_Pos (28) /*!< CLK_T::APBCLK0: EADCCKEN Position */
|
|
#define CLK_APBCLK0_EADCCKEN_Msk (0x1ul << CLK_APBCLK0_EADCCKEN_Pos) /*!< CLK_T::APBCLK0: EADCCKEN Mask */
|
|
|
|
#define CLK_APBCLK0_TKCKEN_Pos (29) /*!< CLK_T::APBCLK0: TKCKEN Position */
|
|
#define CLK_APBCLK0_TKCKEN_Msk (0x1ul << CLK_APBCLK0_TKCKEN_Pos) /*!< CLK_T::APBCLK0: TKCKEN Mask */
|
|
|
|
#define CLK_APBCLK1_SC0CKEN_Pos (0) /*!< CLK_T::APBCLK1: SC0CKEN Position */
|
|
#define CLK_APBCLK1_SC0CKEN_Msk (0x1ul << CLK_APBCLK1_SC0CKEN_Pos) /*!< CLK_T::APBCLK1: SC0CKEN Mask */
|
|
|
|
#define CLK_APBCLK1_USCI0CKEN_Pos (8) /*!< CLK_T::APBCLK1: USCI0CKEN Position */
|
|
#define CLK_APBCLK1_USCI0CKEN_Msk (0x1ul << CLK_APBCLK1_USCI0CKEN_Pos) /*!< CLK_T::APBCLK1: USCI0CKEN Mask */
|
|
|
|
#define CLK_APBCLK1_USCI1CKEN_Pos (9) /*!< CLK_T::APBCLK1: USCI1CKEN Position */
|
|
#define CLK_APBCLK1_USCI1CKEN_Msk (0x1ul << CLK_APBCLK1_USCI1CKEN_Pos) /*!< CLK_T::APBCLK1: USCI1CKEN Mask */
|
|
|
|
#define CLK_APBCLK1_USCI2CKEN_Pos (10) /*!< CLK_T::APBCLK1: USCI2CKEN Position */
|
|
#define CLK_APBCLK1_USCI2CKEN_Msk (0x1ul << CLK_APBCLK1_USCI2CKEN_Pos) /*!< CLK_T::APBCLK1: USCI2CKEN Mask */
|
|
|
|
#define CLK_APBCLK1_DACCKEN_Pos (12) /*!< CLK_T::APBCLK1: DACCKEN Position */
|
|
#define CLK_APBCLK1_DACCKEN_Msk (0x1ul << CLK_APBCLK1_DACCKEN_Pos) /*!< CLK_T::APBCLK1: DACCKEN Mask */
|
|
|
|
#define CLK_APBCLK1_LCDCKEN_Pos (14) /*!< CLK_T::APBCLK1: LCDCKEN Position */
|
|
#define CLK_APBCLK1_LCDCKEN_Msk (0x1ul << CLK_APBCLK1_LCDCKEN_Pos) /*!< CLK_T::APBCLK1: LCDCKEN Mask */
|
|
|
|
#define CLK_APBCLK1_LCDCPCKEN_Pos (15) /*!< CLK_T::APBCLK1: LCDCPCKEN Position */
|
|
#define CLK_APBCLK1_LCDCPCKEN_Msk (0x1ul << CLK_APBCLK1_LCDCPCKEN_Pos) /*!< CLK_T::APBCLK1: LCDCPCKEN Mask */
|
|
|
|
#define CLK_APBCLK1_PWM0CKEN_Pos (16) /*!< CLK_T::APBCLK1: PWM0CKEN Position */
|
|
#define CLK_APBCLK1_PWM0CKEN_Msk (0x1ul << CLK_APBCLK1_PWM0CKEN_Pos) /*!< CLK_T::APBCLK1: PWM0CKEN Mask */
|
|
|
|
#define CLK_APBCLK1_PWM1CKEN_Pos (17) /*!< CLK_T::APBCLK1: PWM1CKEN Position */
|
|
#define CLK_APBCLK1_PWM1CKEN_Msk (0x1ul << CLK_APBCLK1_PWM1CKEN_Pos) /*!< CLK_T::APBCLK1: PWM1CKEN Mask */
|
|
|
|
#define CLK_APBCLK1_BPWM0CKEN_Pos (18) /*!< CLK_T::APBCLK1: BPWM0CKEN Position */
|
|
#define CLK_APBCLK1_BPWM0CKEN_Msk (0x1ul << CLK_APBCLK1_BPWM0CKEN_Pos) /*!< CLK_T::APBCLK1: BPWM0CKEN Mask */
|
|
|
|
#define CLK_APBCLK1_BPWM1CKEN_Pos (19) /*!< CLK_T::APBCLK1: BPWM1CKEN Position */
|
|
#define CLK_APBCLK1_BPWM1CKEN_Msk (0x1ul << CLK_APBCLK1_BPWM1CKEN_Pos) /*!< CLK_T::APBCLK1: BPWM1CKEN Mask */
|
|
|
|
#define CLK_APBCLK1_OPACKEN_Pos (30) /*!< CLK_T::APBCLK1: OPACKEN Position */
|
|
#define CLK_APBCLK1_OPACKEN_Msk (0x1ul << CLK_APBCLK1_OPACKEN_Pos) /*!< CLK_T::APBCLK1: OPACKEN Mask */
|
|
|
|
#define CLK_APBCLK1_PSIOCKEN_Pos (31) /*!< CLK_T::APBCLK1: PSIOCKEN Position */
|
|
#define CLK_APBCLK1_PSIOCKEN_Msk (0x1ul << CLK_APBCLK1_PSIOCKEN_Pos) /*!< CLK_T::APBCLK1: PSIOCKEN Mask */
|
|
|
|
#define CLK_CLKSEL0_HCLKSEL_Pos (0) /*!< CLK_T::CLKSEL0: HCLKSEL Position */
|
|
#define CLK_CLKSEL0_HCLKSEL_Msk (0x7ul << CLK_CLKSEL0_HCLKSEL_Pos) /*!< CLK_T::CLKSEL0: HCLKSEL Mask */
|
|
|
|
#define CLK_CLKSEL0_STCLKSEL_Pos (3) /*!< CLK_T::CLKSEL0: STCLKSEL Position */
|
|
#define CLK_CLKSEL0_STCLKSEL_Msk (0x7ul << CLK_CLKSEL0_STCLKSEL_Pos) /*!< CLK_T::CLKSEL0: STCLKSEL Mask */
|
|
|
|
#define CLK_CLKSEL0_USBDSEL_Pos (8) /*!< CLK_T::CLKSEL0: USBDSEL Position */
|
|
#define CLK_CLKSEL0_USBDSEL_Msk (0x1ul << CLK_CLKSEL0_USBDSEL_Pos) /*!< CLK_T::CLKSEL0: USBDSEL Mask */
|
|
|
|
#define CLK_CLKSEL1_WDTSEL_Pos (0) /*!< CLK_T::CLKSEL1: WDTSEL Position */
|
|
#define CLK_CLKSEL1_WDTSEL_Msk (0x3ul << CLK_CLKSEL1_WDTSEL_Pos) /*!< CLK_T::CLKSEL1: WDTSEL Mask */
|
|
|
|
#define CLK_CLKSEL1_WWDTSEL_Pos (2) /*!< CLK_T::CLKSEL1: WWDTSEL Position */
|
|
#define CLK_CLKSEL1_WWDTSEL_Msk (0x3ul << CLK_CLKSEL1_WWDTSEL_Pos) /*!< CLK_T::CLKSEL1: WWDTSEL Mask */
|
|
|
|
#define CLK_CLKSEL1_CLKOSEL_Pos (4) /*!< CLK_T::CLKSEL1: CLKOSEL Position */
|
|
#define CLK_CLKSEL1_CLKOSEL_Msk (0x7ul << CLK_CLKSEL1_CLKOSEL_Pos) /*!< CLK_T::CLKSEL1: CLKOSEL Mask */
|
|
|
|
#define CLK_CLKSEL1_TMR0SEL_Pos (8) /*!< CLK_T::CLKSEL1: TMR0SEL Position */
|
|
#define CLK_CLKSEL1_TMR0SEL_Msk (0x7ul << CLK_CLKSEL1_TMR0SEL_Pos) /*!< CLK_T::CLKSEL1: TMR0SEL Mask */
|
|
|
|
#define CLK_CLKSEL1_TMR1SEL_Pos (12) /*!< CLK_T::CLKSEL1: TMR1SEL Position */
|
|
#define CLK_CLKSEL1_TMR1SEL_Msk (0x7ul << CLK_CLKSEL1_TMR1SEL_Pos) /*!< CLK_T::CLKSEL1: TMR1SEL Mask */
|
|
|
|
#define CLK_CLKSEL1_TMR2SEL_Pos (16) /*!< CLK_T::CLKSEL1: TMR2SEL Position */
|
|
#define CLK_CLKSEL1_TMR2SEL_Msk (0x7ul << CLK_CLKSEL1_TMR2SEL_Pos) /*!< CLK_T::CLKSEL1: TMR2SEL Mask */
|
|
|
|
#define CLK_CLKSEL1_TMR3SEL_Pos (20) /*!< CLK_T::CLKSEL1: TMR3SEL Position */
|
|
#define CLK_CLKSEL1_TMR3SEL_Msk (0x7ul << CLK_CLKSEL1_TMR3SEL_Pos) /*!< CLK_T::CLKSEL1: TMR3SEL Mask */
|
|
|
|
#define CLK_CLKSEL1_UART0SEL_Pos (24) /*!< CLK_T::CLKSEL1: UART0SEL Position */
|
|
#define CLK_CLKSEL1_UART0SEL_Msk (0x7ul << CLK_CLKSEL1_UART0SEL_Pos) /*!< CLK_T::CLKSEL1: UART0SEL Mask */
|
|
|
|
#define CLK_CLKSEL1_UART1SEL_Pos (28) /*!< CLK_T::CLKSEL1: UART1SEL Position */
|
|
#define CLK_CLKSEL1_UART1SEL_Msk (0x7ul << CLK_CLKSEL1_UART1SEL_Pos) /*!< CLK_T::CLKSEL1: UART1SEL Mask */
|
|
|
|
#define CLK_CLKSEL2_PWM0SEL_Pos (0) /*!< CLK_T::CLKSEL2: PWM0SEL Position */
|
|
#define CLK_CLKSEL2_PWM0SEL_Msk (0x1ul << CLK_CLKSEL2_PWM0SEL_Pos) /*!< CLK_T::CLKSEL2: PWM0SEL Mask */
|
|
|
|
#define CLK_CLKSEL2_PWM1SEL_Pos (1) /*!< CLK_T::CLKSEL2: PWM1SEL Position */
|
|
#define CLK_CLKSEL2_PWM1SEL_Msk (0x1ul << CLK_CLKSEL2_PWM1SEL_Pos) /*!< CLK_T::CLKSEL2: PWM1SEL Mask */
|
|
|
|
#define CLK_CLKSEL2_QSPI0SEL_Pos (2) /*!< CLK_T::CLKSEL2: QSPI0SEL Position */
|
|
#define CLK_CLKSEL2_QSPI0SEL_Msk (0x3ul << CLK_CLKSEL2_QSPI0SEL_Pos) /*!< CLK_T::CLKSEL2: QSPI0SEL Mask */
|
|
|
|
#define CLK_CLKSEL2_SPI0SEL_Pos (4) /*!< CLK_T::CLKSEL2: SPI0SEL Position */
|
|
#define CLK_CLKSEL2_SPI0SEL_Msk (0x3ul << CLK_CLKSEL2_SPI0SEL_Pos) /*!< CLK_T::CLKSEL2: SPI0SEL Mask */
|
|
|
|
#define CLK_CLKSEL2_SPI1SEL_Pos (6) /*!< CLK_T::CLKSEL2: SPI1SEL Position */
|
|
#define CLK_CLKSEL2_SPI1SEL_Msk (0x3ul << CLK_CLKSEL2_SPI1SEL_Pos) /*!< CLK_T::CLKSEL2: SPI1SEL Mask */
|
|
|
|
#define CLK_CLKSEL2_BPWM0SEL_Pos (8) /*!< CLK_T::CLKSEL2: BPWM0SEL Position */
|
|
#define CLK_CLKSEL2_BPWM0SEL_Msk (0x1ul << CLK_CLKSEL2_BPWM0SEL_Pos) /*!< CLK_T::CLKSEL2: BPWM0SEL Mask */
|
|
|
|
#define CLK_CLKSEL2_BPWM1SEL_Pos (9) /*!< CLK_T::CLKSEL2: BPWM1SEL Position */
|
|
#define CLK_CLKSEL2_BPWM1SEL_Msk (0x1ul << CLK_CLKSEL2_BPWM1SEL_Pos) /*!< CLK_T::CLKSEL2: BPWM1SEL Mask */
|
|
|
|
#define CLK_CLKSEL2_LCDSEL_Pos (24) /*!< CLK_T::CLKSEL2: LCDSEL Position */
|
|
#define CLK_CLKSEL2_LCDSEL_Msk (0x1ul << CLK_CLKSEL2_LCDSEL_Pos) /*!< CLK_T::CLKSEL2: LCDSEL Mask */
|
|
|
|
#define CLK_CLKSEL2_LCDCPSEL_Pos (25) /*!< CLK_T::CLKSEL2: LCDCPSEL Position */
|
|
#define CLK_CLKSEL2_LCDCPSEL_Msk (0x1ul << CLK_CLKSEL2_LCDCPSEL_Pos) /*!< CLK_T::CLKSEL2: LCDCPSEL Mask */
|
|
|
|
#define CLK_CLKSEL2_PSIOSEL_Pos (28) /*!< CLK_T::CLKSEL2: PSIOSEL Position */
|
|
#define CLK_CLKSEL2_PSIOSEL_Msk (0x7ul << CLK_CLKSEL2_PSIOSEL_Pos) /*!< CLK_T::CLKSEL2: PSIOSEL Mask */
|
|
|
|
#define CLK_CLKSEL3_SC0SEL_Pos (0) /*!< CLK_T::CLKSEL3: SC0SEL Position */
|
|
#define CLK_CLKSEL3_SC0SEL_Msk (0x3ul << CLK_CLKSEL3_SC0SEL_Pos) /*!< CLK_T::CLKSEL3: SC0SEL Mask */
|
|
|
|
#define CLK_CLKSEL3_UART2SEL_Pos (24) /*!< CLK_T::CLKSEL3: UART2SEL Position */
|
|
#define CLK_CLKSEL3_UART2SEL_Msk (0x7ul << CLK_CLKSEL3_UART2SEL_Pos) /*!< CLK_T::CLKSEL3: UART2SEL Mask */
|
|
|
|
#define CLK_CLKSEL3_UART3SEL_Pos (28) /*!< CLK_T::CLKSEL3: UART3SEL Position */
|
|
#define CLK_CLKSEL3_UART3SEL_Msk (0x7ul << CLK_CLKSEL3_UART3SEL_Pos) /*!< CLK_T::CLKSEL3: UART3SEL Mask */
|
|
|
|
#define CLK_CLKDIV0_HCLKDIV_Pos (0) /*!< CLK_T::CLKDIV0: HCLKDIV Position */
|
|
#define CLK_CLKDIV0_HCLKDIV_Msk (0xful << CLK_CLKDIV0_HCLKDIV_Pos) /*!< CLK_T::CLKDIV0: HCLKDIV Mask */
|
|
|
|
#define CLK_CLKDIV0_USBDIV_Pos (4) /*!< CLK_T::CLKDIV0: USBDIV Position */
|
|
#define CLK_CLKDIV0_USBDIV_Msk (0xful << CLK_CLKDIV0_USBDIV_Pos) /*!< CLK_T::CLKDIV0: USBDIV Mask */
|
|
|
|
#define CLK_CLKDIV0_UART0DIV_Pos (8) /*!< CLK_T::CLKDIV0: UART0DIV Position */
|
|
#define CLK_CLKDIV0_UART0DIV_Msk (0xful << CLK_CLKDIV0_UART0DIV_Pos) /*!< CLK_T::CLKDIV0: UART0DIV Mask */
|
|
|
|
#define CLK_CLKDIV0_UART1DIV_Pos (12) /*!< CLK_T::CLKDIV0: UART1DIV Position */
|
|
#define CLK_CLKDIV0_UART1DIV_Msk (0xful << CLK_CLKDIV0_UART1DIV_Pos) /*!< CLK_T::CLKDIV0: UART1DIV Mask */
|
|
|
|
#define CLK_CLKDIV0_EADCDIV_Pos (16) /*!< CLK_T::CLKDIV0: EADCDIV Position */
|
|
#define CLK_CLKDIV0_EADCDIV_Msk (0xfful << CLK_CLKDIV0_EADCDIV_Pos) /*!< CLK_T::CLKDIV0: EADCDIV Mask */
|
|
|
|
#define CLK_CLKDIV1_SC0DIV_Pos (0) /*!< CLK_T::CLKDIV1: SC0DIV Position */
|
|
#define CLK_CLKDIV1_SC0DIV_Msk (0xfful << CLK_CLKDIV1_SC0DIV_Pos) /*!< CLK_T::CLKDIV1: SC0DIV Mask */
|
|
|
|
#define CLK_CLKDIV1_PSIODIV_Pos (24) /*!< CLK_T::CLKDIV1: PSIODIV Position */
|
|
#define CLK_CLKDIV1_PSIODIV_Msk (0xfful << CLK_CLKDIV1_PSIODIV_Pos) /*!< CLK_T::CLKDIV1: PSIODIV Mask */
|
|
|
|
#define CLK_CLKDIV4_UART2DIV_Pos (0) /*!< CLK_T::CLKDIV4: UART2DIV Position */
|
|
#define CLK_CLKDIV4_UART2DIV_Msk (0xful << CLK_CLKDIV4_UART2DIV_Pos) /*!< CLK_T::CLKDIV4: UART2DIV Mask */
|
|
|
|
#define CLK_CLKDIV4_UART3DIV_Pos (4) /*!< CLK_T::CLKDIV4: UART3DIV Position */
|
|
#define CLK_CLKDIV4_UART3DIV_Msk (0xful << CLK_CLKDIV4_UART3DIV_Pos) /*!< CLK_T::CLKDIV4: UART3DIV Mask */
|
|
|
|
#define CLK_PCLKDIV_APB0DIV_Pos (0) /*!< CLK_T::PCLKDIV: APB0DIV Position */
|
|
#define CLK_PCLKDIV_APB0DIV_Msk (0x7ul << CLK_PCLKDIV_APB0DIV_Pos) /*!< CLK_T::PCLKDIV: APB0DIV Mask */
|
|
|
|
#define CLK_PCLKDIV_APB1DIV_Pos (4) /*!< CLK_T::PCLKDIV: APB1DIV Position */
|
|
#define CLK_PCLKDIV_APB1DIV_Msk (0x7ul << CLK_PCLKDIV_APB1DIV_Pos) /*!< CLK_T::PCLKDIV: APB1DIV Mask */
|
|
|
|
#define CLK_PLLCTL_FBDIV_Pos (0) /*!< CLK_T::PLLCTL: FBDIV Position */
|
|
#define CLK_PLLCTL_FBDIV_Msk (0x3ful << CLK_PLLCTL_FBDIV_Pos) /*!< CLK_T::PLLCTL: FBDIV Mask */
|
|
|
|
#define CLK_PLLCTL_INDIV_Pos (9) /*!< CLK_T::PLLCTL: INDIV Position */
|
|
#define CLK_PLLCTL_INDIV_Msk (0xful << CLK_PLLCTL_INDIV_Pos) /*!< CLK_T::PLLCTL: INDIV Mask */
|
|
|
|
#define CLK_PLLCTL_OUTDIV_Pos (14) /*!< CLK_T::PLLCTL: OUTDIV Position */
|
|
#define CLK_PLLCTL_OUTDIV_Msk (0x3ul << CLK_PLLCTL_OUTDIV_Pos) /*!< CLK_T::PLLCTL: OUTDIV Mask */
|
|
|
|
#define CLK_PLLCTL_PD_Pos (16) /*!< CLK_T::PLLCTL: PD Position */
|
|
#define CLK_PLLCTL_PD_Msk (0x1ul << CLK_PLLCTL_PD_Pos) /*!< CLK_T::PLLCTL: PD Mask */
|
|
|
|
#define CLK_PLLCTL_BP_Pos (17) /*!< CLK_T::PLLCTL: BP Position */
|
|
#define CLK_PLLCTL_BP_Msk (0x1ul << CLK_PLLCTL_BP_Pos) /*!< CLK_T::PLLCTL: BP Mask */
|
|
|
|
#define CLK_PLLCTL_OE_Pos (18) /*!< CLK_T::PLLCTL: OE Position */
|
|
#define CLK_PLLCTL_OE_Msk (0x1ul << CLK_PLLCTL_OE_Pos) /*!< CLK_T::PLLCTL: OE Mask */
|
|
|
|
#define CLK_PLLCTL_PLLSRC_Pos (19) /*!< CLK_T::PLLCTL: PLLSRC Position */
|
|
#define CLK_PLLCTL_PLLSRC_Msk (0x3ul << CLK_PLLCTL_PLLSRC_Pos) /*!< CLK_T::PLLCTL: PLLSRC Mask */
|
|
|
|
#define CLK_PLLCTL_STBSEL_Pos (23) /*!< CLK_T::PLLCTL: STBSEL Position */
|
|
#define CLK_PLLCTL_STBSEL_Msk (0x1ul << CLK_PLLCTL_STBSEL_Pos) /*!< CLK_T::PLLCTL: STBSEL Mask */
|
|
|
|
#define CLK_PLLCTL_PLL_CLF_EN_Pos (24) /*!< CLK_T::PLLCTL: PLL_CLF_EN Position */
|
|
#define CLK_PLLCTL_PLL_CLF_EN_Msk (0x1ul << CLK_PLLCTL_PLL_CLF_EN_Pos) /*!< CLK_T::PLLCTL: PLL_CLF_EN Mask */
|
|
|
|
#define CLK_STATUS_HXTSTB_Pos (0) /*!< CLK_T::STATUS: HXTSTB Position */
|
|
#define CLK_STATUS_HXTSTB_Msk (0x1ul << CLK_STATUS_HXTSTB_Pos) /*!< CLK_T::STATUS: HXTSTB Mask */
|
|
|
|
#define CLK_STATUS_LXTSTB_Pos (1) /*!< CLK_T::STATUS: LXTSTB Position */
|
|
#define CLK_STATUS_LXTSTB_Msk (0x1ul << CLK_STATUS_LXTSTB_Pos) /*!< CLK_T::STATUS: LXTSTB Mask */
|
|
|
|
#define CLK_STATUS_PLLSTB_Pos (2) /*!< CLK_T::STATUS: PLLSTB Position */
|
|
#define CLK_STATUS_PLLSTB_Msk (0x1ul << CLK_STATUS_PLLSTB_Pos) /*!< CLK_T::STATUS: PLLSTB Mask */
|
|
|
|
#define CLK_STATUS_LIRCSTB_Pos (3) /*!< CLK_T::STATUS: LIRCSTB Position */
|
|
#define CLK_STATUS_LIRCSTB_Msk (0x1ul << CLK_STATUS_LIRCSTB_Pos) /*!< CLK_T::STATUS: LIRCSTB Mask */
|
|
|
|
#define CLK_STATUS_HIRCSTB_Pos (4) /*!< CLK_T::STATUS: HIRCSTB Position */
|
|
#define CLK_STATUS_HIRCSTB_Msk (0x1ul << CLK_STATUS_HIRCSTB_Pos) /*!< CLK_T::STATUS: HIRCSTB Mask */
|
|
|
|
#define CLK_STATUS_MIRCSTB_Pos (6) /*!< CLK_T::STATUS: MIRCSTB Position */
|
|
#define CLK_STATUS_MIRCSTB_Msk (0x1ul << CLK_STATUS_MIRCSTB_Pos) /*!< CLK_T::STATUS: MIRCSTB Mask */
|
|
|
|
#define CLK_STATUS_CLKSFAIL_Pos (7) /*!< CLK_T::STATUS: CLKSFAIL Position */
|
|
#define CLK_STATUS_CLKSFAIL_Msk (0x1ul << CLK_STATUS_CLKSFAIL_Pos) /*!< CLK_T::STATUS: CLKSFAIL Mask */
|
|
|
|
#define CLK_CLKOCTL_FREQSEL_Pos (0) /*!< CLK_T::CLKOCTL: FREQSEL Position */
|
|
#define CLK_CLKOCTL_FREQSEL_Msk (0xful << CLK_CLKOCTL_FREQSEL_Pos) /*!< CLK_T::CLKOCTL: FREQSEL Mask */
|
|
|
|
#define CLK_CLKOCTL_CLKOEN_Pos (4) /*!< CLK_T::CLKOCTL: CLKOEN Position */
|
|
#define CLK_CLKOCTL_CLKOEN_Msk (0x1ul << CLK_CLKOCTL_CLKOEN_Pos) /*!< CLK_T::CLKOCTL: CLKOEN Mask */
|
|
|
|
#define CLK_CLKOCTL_DIV1EN_Pos (5) /*!< CLK_T::CLKOCTL: DIV1EN Position */
|
|
#define CLK_CLKOCTL_DIV1EN_Msk (0x1ul << CLK_CLKOCTL_DIV1EN_Pos) /*!< CLK_T::CLKOCTL: DIV1EN Mask */
|
|
|
|
#define CLK_CLKOCTL_CLK1HZEN_Pos (6) /*!< CLK_T::CLKOCTL: CLK1HZEN Position */
|
|
#define CLK_CLKOCTL_CLK1HZEN_Msk (0x1ul << CLK_CLKOCTL_CLK1HZEN_Pos) /*!< CLK_T::CLKOCTL: CLK1HZEN Mask */
|
|
|
|
#define CLK_CLKDCTL_HXTFDEN_Pos (4) /*!< CLK_T::CLKDCTL: HXTFDEN Position */
|
|
#define CLK_CLKDCTL_HXTFDEN_Msk (0x1ul << CLK_CLKDCTL_HXTFDEN_Pos) /*!< CLK_T::CLKDCTL: HXTFDEN Mask */
|
|
|
|
#define CLK_CLKDCTL_HXTFIEN_Pos (5) /*!< CLK_T::CLKDCTL: HXTFIEN Position */
|
|
#define CLK_CLKDCTL_HXTFIEN_Msk (0x1ul << CLK_CLKDCTL_HXTFIEN_Pos) /*!< CLK_T::CLKDCTL: HXTFIEN Mask */
|
|
|
|
#define CLK_CLKDCTL_LXTFDEN_Pos (12) /*!< CLK_T::CLKDCTL: LXTFDEN Position */
|
|
#define CLK_CLKDCTL_LXTFDEN_Msk (0x1ul << CLK_CLKDCTL_LXTFDEN_Pos) /*!< CLK_T::CLKDCTL: LXTFDEN Mask */
|
|
|
|
#define CLK_CLKDCTL_LXTFIEN_Pos (13) /*!< CLK_T::CLKDCTL: LXTFIEN Position */
|
|
#define CLK_CLKDCTL_LXTFIEN_Msk (0x1ul << CLK_CLKDCTL_LXTFIEN_Pos) /*!< CLK_T::CLKDCTL: LXTFIEN Mask */
|
|
|
|
#define CLK_CLKDCTL_HXTFQDEN_Pos (16) /*!< CLK_T::CLKDCTL: HXTFQDEN Position */
|
|
#define CLK_CLKDCTL_HXTFQDEN_Msk (0x1ul << CLK_CLKDCTL_HXTFQDEN_Pos) /*!< CLK_T::CLKDCTL: HXTFQDEN Mask */
|
|
|
|
#define CLK_CLKDCTL_HXTFQIEN_Pos (17) /*!< CLK_T::CLKDCTL: HXTFQIEN Position */
|
|
#define CLK_CLKDCTL_HXTFQIEN_Msk (0x1ul << CLK_CLKDCTL_HXTFQIEN_Pos) /*!< CLK_T::CLKDCTL: HXTFQIEN Mask */
|
|
|
|
#define CLK_CLKDSTS_HXTFIF_Pos (0) /*!< CLK_T::CLKDSTS: HXTFIF Position */
|
|
#define CLK_CLKDSTS_HXTFIF_Msk (0x1ul << CLK_CLKDSTS_HXTFIF_Pos) /*!< CLK_T::CLKDSTS: HXTFIF Mask */
|
|
|
|
#define CLK_CLKDSTS_LXTFIF_Pos (1) /*!< CLK_T::CLKDSTS: LXTFIF Position */
|
|
#define CLK_CLKDSTS_LXTFIF_Msk (0x1ul << CLK_CLKDSTS_LXTFIF_Pos) /*!< CLK_T::CLKDSTS: LXTFIF Mask */
|
|
|
|
#define CLK_CLKDSTS_HXTFQIF_Pos (8) /*!< CLK_T::CLKDSTS: HXTFQIF Position */
|
|
#define CLK_CLKDSTS_HXTFQIF_Msk (0x1ul << CLK_CLKDSTS_HXTFQIF_Pos) /*!< CLK_T::CLKDSTS: HXTFQIF Mask */
|
|
|
|
#define CLK_CDUPB_UPERBD_Pos (0) /*!< CLK_T::CDUPB: UPERBD Position */
|
|
#define CLK_CDUPB_UPERBD_Msk (0x3fful << CLK_CDUPB_UPERBD_Pos) /*!< CLK_T::CDUPB: UPERBD Mask */
|
|
|
|
#define CLK_CDLOWB_LOWERBD_Pos (0) /*!< CLK_T::CDLOWB: LOWERBD Position */
|
|
#define CLK_CDLOWB_LOWERBD_Msk (0x3fful << CLK_CDLOWB_LOWERBD_Pos) /*!< CLK_T::CDLOWB: LOWERBD Mask */
|
|
|
|
#define CLK_PMUCTL_PDMSEL_Pos (0) /*!< CLK_T::PMUCTL: PDMSEL Position */
|
|
#define CLK_PMUCTL_PDMSEL_Msk (0x7ul << CLK_PMUCTL_PDMSEL_Pos) /*!< CLK_T::PMUCTL: PDMSEL Mask */
|
|
|
|
#define CLK_PMUCTL_WKTMREN_Pos (8) /*!< CLK_T::PMUCTL: WKTMREN Position */
|
|
#define CLK_PMUCTL_WKTMREN_Msk (0x1ul << CLK_PMUCTL_WKTMREN_Pos) /*!< CLK_T::PMUCTL: WKTMREN Mask */
|
|
|
|
#define CLK_PMUCTL_WKTMRIS_Pos (9) /*!< CLK_T::PMUCTL: WKTMRIS Position */
|
|
#define CLK_PMUCTL_WKTMRIS_Msk (0x7ul << CLK_PMUCTL_WKTMRIS_Pos) /*!< CLK_T::PMUCTL: WKTMRIS Mask */
|
|
|
|
#define CLK_PMUCTL_WKPINEN0_Pos (16) /*!< CLK_T::PMUCTL: WKPINEN0 Position */
|
|
#define CLK_PMUCTL_WKPINEN0_Msk (0x3ul << CLK_PMUCTL_WKPINEN0_Pos) /*!< CLK_T::PMUCTL: WKPINEN0 Mask */
|
|
|
|
#define CLK_PMUCTL_WKPINDBEN_Pos (22) /*!< CLK_T::PMUCTL: WKPINDBEN Position */
|
|
#define CLK_PMUCTL_WKPINDBEN_Msk (0x1ul << CLK_PMUCTL_WKPINDBEN_Pos) /*!< CLK_T::PMUCTL: WKPINDBEN Mask */
|
|
|
|
#define CLK_PMUCTL_RTCWKEN_Pos (23) /*!< CLK_T::PMUCTL: RTCWKEN Position */
|
|
#define CLK_PMUCTL_RTCWKEN_Msk (0x1ul << CLK_PMUCTL_RTCWKEN_Pos) /*!< CLK_T::PMUCTL: RTCWKEN Mask */
|
|
|
|
#define CLK_PMUCTL_WKPINEN1_Pos (24) /*!< CLK_T::PMUCTL: WKPINEN1 Position */
|
|
#define CLK_PMUCTL_WKPINEN1_Msk (0x3ul << CLK_PMUCTL_WKPINEN1_Pos) /*!< CLK_T::PMUCTL: WKPINEN1 Mask */
|
|
|
|
#define CLK_PMUCTL_WKPINEN2_Pos (26) /*!< CLK_T::PMUCTL: WKPINEN2 Position */
|
|
#define CLK_PMUCTL_WKPINEN2_Msk (0x3ul << CLK_PMUCTL_WKPINEN2_Pos) /*!< CLK_T::PMUCTL: WKPINEN2 Mask */
|
|
|
|
#define CLK_PMUCTL_WKPINEN3_Pos (28) /*!< CLK_T::PMUCTL: WKPINEN3 Position */
|
|
#define CLK_PMUCTL_WKPINEN3_Msk (0x3ul << CLK_PMUCTL_WKPINEN3_Pos) /*!< CLK_T::PMUCTL: WKPINEN3 Mask */
|
|
|
|
#define CLK_PMUCTL_WKPINEN4_Pos (30) /*!< CLK_T::PMUCTL: WKPINEN4 Position */
|
|
#define CLK_PMUCTL_WKPINEN4_Msk (0x3ul << CLK_PMUCTL_WKPINEN4_Pos) /*!< CLK_T::PMUCTL: WKPINEN4 Mask */
|
|
|
|
#define CLK_PMUSTS_PINWK0_Pos (0) /*!< CLK_T::PMUSTS: PINWK0 Position */
|
|
#define CLK_PMUSTS_PINWK0_Msk (0x1ul << CLK_PMUSTS_PINWK0_Pos) /*!< CLK_T::PMUSTS: PINWK0 Mask */
|
|
|
|
#define CLK_PMUSTS_TMRWK_Pos (1) /*!< CLK_T::PMUSTS: TMRWK Position */
|
|
#define CLK_PMUSTS_TMRWK_Msk (0x1ul << CLK_PMUSTS_TMRWK_Pos) /*!< CLK_T::PMUSTS: TMRWK Mask */
|
|
|
|
#define CLK_PMUSTS_RTCWK_Pos (2) /*!< CLK_T::PMUSTS: RTCWK Position */
|
|
#define CLK_PMUSTS_RTCWK_Msk (0x1ul << CLK_PMUSTS_RTCWK_Pos) /*!< CLK_T::PMUSTS: RTCWK Mask */
|
|
|
|
#define CLK_PMUSTS_PINWK1_Pos (3) /*!< CLK_T::PMUSTS: PINWK1 Position */
|
|
#define CLK_PMUSTS_PINWK1_Msk (0x1ul << CLK_PMUSTS_PINWK1_Pos) /*!< CLK_T::PMUSTS: PINWK1 Mask */
|
|
|
|
#define CLK_PMUSTS_PINWK2_Pos (4) /*!< CLK_T::PMUSTS: PINWK2 Position */
|
|
#define CLK_PMUSTS_PINWK2_Msk (0x1ul << CLK_PMUSTS_PINWK2_Pos) /*!< CLK_T::PMUSTS: PINWK2 Mask */
|
|
|
|
#define CLK_PMUSTS_PINWK3_Pos (5) /*!< CLK_T::PMUSTS: PINWK3 Position */
|
|
#define CLK_PMUSTS_PINWK3_Msk (0x1ul << CLK_PMUSTS_PINWK3_Pos) /*!< CLK_T::PMUSTS: PINWK3 Mask */
|
|
|
|
#define CLK_PMUSTS_PINWK4_Pos (6) /*!< CLK_T::PMUSTS: PINWK4 Position */
|
|
#define CLK_PMUSTS_PINWK4_Msk (0x1ul << CLK_PMUSTS_PINWK4_Pos) /*!< CLK_T::PMUSTS: PINWK4 Mask */
|
|
|
|
#define CLK_PMUSTS_LVRWK_Pos (12) /*!< CLK_T::PMUSTS: LVRWK Position */
|
|
#define CLK_PMUSTS_LVRWK_Msk (0x1ul << CLK_PMUSTS_LVRWK_Pos) /*!< CLK_T::PMUSTS: LVRWK Mask */
|
|
|
|
#define CLK_PMUSTS_CLRWK_Pos (31) /*!< CLK_T::PMUSTS: CLRWK Position */
|
|
#define CLK_PMUSTS_CLRWK_Msk (0x1ul << CLK_PMUSTS_CLRWK_Pos) /*!< CLK_T::PMUSTS: CLRWK Mask */
|
|
|
|
#define CLK_HXTFSEL_HXTFSEL_Pos (0) /*!< CLK_T::HXTFSEL: HXTFSEL Position */
|
|
#define CLK_HXTFSEL_HXTFSEL_Msk (0x1ul << CLK_HXTFSEL_HXTFSEL_Pos) /*!< CLK_T::HXTFSEL: HXTFSEL Mask */
|
|
|
|
/** @} CLK_CONST */
|
|
/** @} end of CLK register group */
|
|
/** @} end of REGISTER group */
|
|
|
|
#if defined ( __CC_ARM )
|
|
#pragma no_anon_unions
|
|
#endif
|
|
|
|
#endif /* __CLK_REG_H__ */
|