Macintosh-SW/mac-rom-simm-programmer
1
0
Fork 0
mirror of https://github.com/dougg3/mac-rom-simm-programmer.git synced 2024-12-11 07:50:36 +00:00
Code Issues Projects Releases Wiki Activity
71164460f3
mac-rom-simm-programmer/hal/m258ke/nuvoton/pdma_reg.h

735 lines
53 KiB
C
Raw Blame History

/**************************************************************************//**
* @file pdma_reg.h
* @version V1.00
* @brief PDMA register definition header file
*
* SPDX-License-Identifier: Apache-2.0
* @copyright (C) 2019 Nuvoton Technology Corp. All rights reserved.
*****************************************************************************/
#ifndef __PDMA_REG_H__
#define __PDMA_REG_H__
#if defined ( __CC_ARM )
#pragma anon_unions
#endif
/**
@addtogroup REGISTER Control Register
@{
*/
/**
@addtogroup PDMA Peripheral Direct Memory Access Controller (PDMA)
Memory Mapped Structure for PDMA Controller
@{
*/
typedef struct
{
/**
* @var DSCT_T::CTL
* Offset: 0x00 Descriptor Table Control Register of PDMA Channel n
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[1:0] |OPMODE |PDMA Operation Mode Selection
* | | |00 = Idle state: Channel is stopped or this table is complete, when PDMA finish channel table task, OPMODE will be cleared to idle state automatically.
* | | |01 = Basic mode: The descriptor table only has one task
* | | |When this task is finished, the PDMA_INTSTS[n] will be asserted.
* | | |10 = Scatter-Gather mode: When operating in this mode, user must give the next descriptor table address in PDMA_DSCT_NEXT register; PDMA controller will ignore this task, then load the next task to execute.
* | | |11 = Reserved.
* | | |Note: Before filling transfer task in the Descriptor Table, user must check if the descriptor table is complete.
* |[2] |TXTYPE |Transfer Type
* | | |0 = Burst transfer type.
* | | |1 = Single transfer type.
* |[6:4] |BURSIZE |Burst Size
* | | |This field is used for peripheral to determine the burst size or used for determine the re-arbitration size.
* | | |000 = 128 Transfers.
* | | |001 = 64 Transfers.
* | | |010 = 32 Transfers.
* | | |011 = 16 Transfers.
* | | |100 = 8 Transfers.
* | | |101 = 4 Transfers.
* | | |110 = 2 Transfers.
* | | |111 = 1 Transfers.
* | | |Note: This field is only useful in burst transfer type.
* |[7] |TBINTDIS |Table Interrupt Disable Bit
* | | |This field can be used to decide whether to enable table interrupt or not
* | | |If the TBINTDIS bit is enabled when PDMA controller finishes transfer task, it will not generates transfer done interrupt.
* | | |0 = Table interrupt Enabled.
* | | |1 = Table interrupt Disabled.
* |[9:8] |SAINC |Source Address Increment
* | | |This field is used to set the source address increment size.
* | | |11 = No increment (fixed address).
* | | |Others = Increment and size is depended on TXWIDTH selection.
* |[11:10] |DAINC |Destination Address Increment
* | | |This field is used to set the destination address increment size.
* | | |11 = No increment (fixed address).
* | | |Others = Increment and size is depended on TXWIDTH selection.
* |[13:12] |TXWIDTH |Transfer Width Selection
* | | |This field is used for transfer width.
* | | |00 = One byte (8 bit) is transferred for every operation.
* | | |01= One half-word (16 bit) is transferred for every operation.
* | | |10 = One word (32-bit) is transferred for every operation.
* | | |11 = Reserved.
* | | |Note: The PDMA transfer source address (PDMA_DSCT_SA) and PDMA transfer destination address (PDMA_DSCT_DA) should be alignment under the TXWIDTH selection
* |[14] |TXACK |Transfer Acknowledge Selection
* | | |0 = transfer ack when transfer done.
* | | |1 = transfer ack when PDMA get transfer data.
* | | |Note: This function only support UART_RX and SPI_RX.
* |[15] |STRIDEEN |Stride Mode Enable Bit
* | | |0 = Stride transfer mode Disabled.
* | | |1 = Stride transfer mode Enabled.
* |[31:16] |TXCNT |Transfer Count
* | | |The TXCNT represents the required number of PDMA transfer, the real transfer count is (TXCNT + 1); The maximum transfer count is 65536, every transfer may be byte, half-word or word that is dependent on TXWIDTH field.
* | | |Note: When PDMA finish each transfer data, this field will be decrease immediately.
* @var DSCT_T::SA
* Offset: 0x04 Source Address Register of PDMA Channel n
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[31:0] |SA |PDMA Transfer Source Address
* | | |This field indicates a 32-bit source address of PDMA controller.
* @var DSCT_T::DA
* Offset: 0x08 Destination Address Register of PDMA Channel n
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[31:0] |DA |PDMA Transfer Destination Address
* | | |This field indicates a 32-bit destination address of PDMA controller.
* @var DSCT_T::NEXT
* Offset: 0x0C Next Scatter-gather Descriptor Table Offset Address of PDMA Channel n
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[15:0] |NEXT |PDMA Next Descriptor Table Offset
* | | |This field indicates the offset of the next descriptor table address in system memory.
* | | |Write Operation:
* | | |If the system memory based address is 0x2000_0000 (PDMA_SCATBA), and the next descriptor table is start from 0x2000_0100, then this field must fill in 0x0100.
* | | |Read Operation:
* | | |When operating in scatter-gather mode, the last two bits NEXT[1:0] will become reserved, and indicate the first next address of system memory.
* | | |When operating in scatter-gather mode, the last two bits NEXT[1:0] will become scatter-gather mode control indicator as below.
* | | |0 = Idle mode.
* | | |1 = operating in the basic mode (final scatter-gather table).
* | | |2 = loading scatter-gather table from SRAM.
* | | |3 = operating in the scatter-gather mode.
* | | |Note1: The descriptor table address must be word boundary.
* | | |Note2: Before filled transfer task in the descriptor table, user must check if the descriptor table is complete.
* |[31:16] |EXENEXT |PDMA Execution Next Descriptor Table Offset
* | | |This field indicates the offset of next descriptor table address of current execution descriptor table in system memory.
* | | |Note: write operation is useless in this field.
*/
__IO uint32_t CTL; /*!< [0x0000] Descriptor Table Control Register of PDMA Channel n. */
__IO uint32_t SA; /*!< [0x0004] Source Address Register of PDMA Channel n */
__IO uint32_t DA; /*!< [0x0008] Destination Address Register of PDMA Channel n */
__IO uint32_t NEXT; /*!< [0x000c] First Scatter-Gather Descriptor Table Offset Address of PDMA Channel n */
} DSCT_T;
typedef struct
{
/**
* @var STRIDE_T::STC
* Offset: 0x500 Stride Transfer Count Register of PDMA Channel n
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[15:0] |STC |PDMA Stride Transfer Count
* | | |The 16-bit register defines the stride transfer count of each row.
* @var STRIDE_T::ASOCR
* Offset: 0x504 Address Stride Offset Register of PDMA Channel n
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[15:0] |SASOL |VDMA Source Address Stride Offset Length
* | | |The 16-bit register defines the source address stride transfer offset count of each row.
* |[31:16] |DASOL |VDMA Destination Address Stride Offset Length
* | | |The 16-bit register defines the destination address stride transfer offset count of each row.
*/
__IO uint32_t STC; /*!< [0x0500] Stride Transfer Count Register of PDMA Channel 0 */
__IO uint32_t ASOCR; /*!< [0x0504] Address Stride Offset Register of PDMA Channel 0 */
} STRIDE_T;
typedef struct
{
/**
* @var PDMA_T::CURSCAT
* Offset: 0x100 Current Scatter-gather Descriptor Table Address of PDMA Channel n
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[31:0] |CURADDR |PDMA Current Description Address (Read Only)
* | | |This field indicates a 32-bit current external description address of PDMA controller.
* | | |Note: This field is read only and used for Scatter-Gather mode only to indicate the current external description address.
* @var PDMA_T::CHCTL
* Offset: 0x400 PDMA Channel Control Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |CHENn |PDMA Channel Enable Bits
* | | |Set this bit to 1 to enable PDMAn operation. Channel cannot be active if it is not set as enabled.
* | | |0 = PDMA channel [n] Disabled.
* | | |1 = PDMA channel [n] Enabled.
* | | |Note: Setting the corresponding bit of PDMA_PAUSE or PDMA_CHRST register will also clear this bit.
* @var PDMA_T::PAUSE
* Offset: 0x404 PDMA Transfer Pause Control Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |PAUSEn |PDMA Channel N Transfer Pause Control (Write Only)
* | | |User can set PAUSEn bit field to pause the PDMA transfer
* | | |When user sets PAUSEn bit, the PDMA controller will pause the on-going transfer, then clear the channel enable bit CHEN(PDMA_CHCTL [n], n=0,1..7) and clear request active flag
* | | |If the paused channel is re-enabled again, the remaining transfers will be processed.
* | | |0 = No effect.
* | | |1 = Pause PDMA channel n transfer.
* @var PDMA_T::SWREQ
* Offset: 0x408 PDMA Software Request Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |SWREQn |PDMA Software Request (Write Only)
* | | |Set this bit to 1 to generate a software request to PDMA [n].
* | | |0 = No effect.
* | | |1 = Generate a software request.
* | | |Note1: User can read PDMA_TRGSTS register to know which channel is on active
* | | |Active flag may be triggered by software request or peripheral request.
* | | |Note2: If user does not enable corresponding PDMA channel, the software request will be ignored.
* @var PDMA_T::TRGSTS
* Offset: 0x40C PDMA Channel Request Status Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |REQSTSn |PDMA Channel Request Status (Read Only)
* | | |This flag indicates whether channel[n] have a request or not, no matter request from software or peripheral
* | | |When PDMA controller finishes channel transfer, this bit will be cleared automatically.
* | | |0 = PDMA Channel n has no request.
* | | |1 = PDMA Channel n has a request.
* | | |Note: If user pauses or resets each PDMA transfer by setting PDMA_PAUSE or PDMA_CHRST register respectively, this bit will be cleared automatically after finishing the current transfer.
* @var PDMA_T::PRISET
* Offset: 0x410 PDMA Fixed Priority Setting Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |FPRISETn |PDMA Fixed Priority Setting
* | | |Set this bit to 1 to enable fixed priority level.
* | | |Write Operation:
* | | |0 = No effect.
* | | |1 = Set PDMA channel [n] to fixed priority channel.
* | | |Read Operation:
* | | |0 = Corresponding PDMA channel is round-robin priority.
* | | |1 = Corresponding PDMA channel is fixed priority.
* | | |Note: This field only set to fixed priority, clear fixed priority use PDMA_PRICLR register.
* @var PDMA_T::PRICLR
* Offset: 0x414 PDMA Fixed Priority Clear Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |FPRICLRn |PDMA Fixed Priority Clear Bits (Write Only)
* | | |Set this bit to 1 to clear fixed priority level.
* | | |0 = No effect.
* | | |1 = Clear PDMA channel [n] fixed priority setting.
* | | |Note: User can read PDMA_PRISET register to know the channel priority.
* @var PDMA_T::INTEN
* Offset: 0x418 PDMA Interrupt Enable Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |INTENn |PDMA Interrupt Enable Bits
* | | |This field is used to enable PDMA channel[n] interrupt.
* | | |0 = PDMA channel n interrupt Disabled.
* | | |1 = PDMA channel n interrupt Enabled.
* @var PDMA_T::INTSTS
* Offset: 0x41C PDMA Interrupt Status Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[0] |ABTIF |PDMA Read/Write Target Abort Interrupt Flag (Read Only)
* | | |This bit indicates that PDMA has target abort error; Software can read PDMA_ABTSTS register to find which channel has target abort error.
* | | |0 = No AHB bus ERROR response received.
* | | |1 = AHB bus ERROR response received.
* |[1] |TDIF |Transfer Done Interrupt Flag (Read Only)
* | | |This bit indicates that PDMA controller has finished transmission; User can read PDMA_TDSTS register to indicate which channel finished transfer.
* | | |0 = Not finished yet.
* | | |1 = PDMA channel has finished transmission.
* |[2] |ALIGNF |Transfer Alignment Interrupt Flag (Read Only)
* | | |0 = PDMA channel source address and destination address both follow transfer width setting.
* | | |1 = PDMA channel source address or destination address is not follow transfer width setting.
* |[8] |REQTOF0 |Request Time-out Flag for Channel 0
* | | |This flag indicates that PDMA controller has waited peripheral request for a period defined by PDMA_TOC0, user can write 1 to clear these bits.
* | | |0 = No request time-out.
* | | |1 = Peripheral request time-out.
* |[9] |REQTOF1 |Request Time-out Flag for Channel 1
* | | |This flag indicates that PDMA controller has waited peripheral request for a period defined by PDMA_TOC1, user can write 1 to clear these bits.
* | | |0 = No request time-out.
* | | |1 = Peripheral request time-out.
* @var PDMA_T::ABTSTS
* Offset: 0x420 PDMA Channel Read/Write Target Abort Flag Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |ABTIFn |PDMA Read/Write Target Abort Interrupt Status Flag
* | | |This bit indicates which PDMA controller has target abort error; User can write 1 to clear these bits.
* | | |0 = No AHB bus ERROR response received when channel n transfer.
* | | |1 = AHB bus ERROR response received when channel n transfer.
* @var PDMA_T::TDSTS
* Offset: 0x424 PDMA Channel Transfer Done Flag Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |TDIF0 |Transfer Done Flag
* | | |This bit indicates whether PDMA controller channel transfer has been finished or not, user can write 1 to clear these bits.
* | | |0 = PDMA channel transfer has not finished.
* | | |1 = PDMA channel has finished transmission.
* @var PDMA_T::ALIGN
* Offset: 0x428 PDMA Transfer Alignment Status Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |ALIGNn |Transfer Alignment Flag
* | | |0 = PDMA channel source address and destination address both follow transfer width setting.
* | | |1 = PDMA channel source address or destination address is not follow transfer width setting.
* @var PDMA_T::TACTSTS
* Offset: 0x42C PDMA Transfer Active Flag Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |TXACTFn |Transfer on Active Flag (Read Only)
* | | |This bit indicates which PDMA channel is in active.
* | | |0 = PDMA channel is not finished.
* | | |1 = PDMA channel is active.
* @var PDMA_T::TOUTPSC
* Offset: 0x430 PDMA Time-out Prescaler Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[2:0] |TOUTPSC0 |PDMA Channel 0 Time-out Clock Source Prescaler Bits
* | | |000 = PDMA channel 0 time-out clock source is HCLK/28.
* | | |001 = PDMA channel 0 time-out clock source is HCLK/29.
* | | |010 = PDMA channel 0 time-out clock source is HCLK/210.
* | | |011 = PDMA channel 0 time-out clock source is HCLK/211.
* | | |100 = PDMA channel 0 time-out clock source is HCLK/212.
* | | |101 = PDMA channel 0 time-out clock source is HCLK/213.
* | | |110 = PDMA channel 0 time-out clock source is HCLK/214.
* | | |111 = PDMA channel 0 time-out clock source is HCLK/215.
* |[6:4] |TOUTPSC1 |PDMA Channel 1 Time-out Clock Source Prescaler Bits
* | | |000 = PDMA channel 1 time-out clock source is HCLK/28.
* | | |001 = PDMA channel 1 time-out clock source is HCLK/29.
* | | |010 = PDMA channel 1 time-out clock source is HCLK/210.
* | | |011 = PDMA channel 1 time-out clock source is HCLK/211.
* | | |100 = PDMA channel 1 time-out clock source is HCLK/212.
* | | |101 = PDMA channel 1 time-out clock source is HCLK/213.
* | | |110 = PDMA channel 1 time-out clock source is HCLK/214.
* | | |111 = PDMA channel 1 time-out clock source is HCLK/215.
* @var PDMA_T::TOUTEN
* Offset: 0x434 PDMA Time-out Enable Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[1:0] |TOUTENn |PDMA Time-out Enable Bits
* | | |0 = PDMA Channel n time-out function Disabled.
* | | |1 = PDMA Channel n time-out function Enabled.
* @var PDMA_T::TOUTIEN
* Offset: 0x438 PDMA Time-out Interrupt Enable Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[1:0] |TOUTIENn |PDMA Time-out Interrupt Enable Bits
* | | |0 = PDMA Channel n time-out interrupt Disabled.
* | | |1 = PDMA Channel n time-out interrupt Enabled.
* @var PDMA_T::SCATBA
* Offset: 0x43C PDMA Scatter-gather Descriptor Table Base Address Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[31:16] |SCATBA |PDMA Scatter-gather Descriptor Table Address
* | | |In Scatter-Gather mode, this is the base address for calculating the next link - list address
* | | |The next link address equation is
* | | |Next Link Address = PDMA_SCATBA + PDMA_DSCT_NEXT.
* | | |Note: Only useful in Scatter-Gather mode.
* @var PDMA_T::TOC0_1
* Offset: 0x440 PDMA Time-out Counter Ch1 and Ch0 Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[15:0] |TOC0 |Time-out Counter for Channel 0
* | | |This controls the period of time-out function for channel 0
* | | |The calculation unit is based on 10 kHz clock.
* |[31:16] |TOC1 |Time-out Counter for Channel 1
* | | |This controls the period of time-out function for channel 1
* | | |The calculation unit is based on 10 kHz clock.
* @var PDMA_T::CHRST
* Offset: 0x460 PDMA Channel Reset Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[15:0] |CHnRST |Channel N Reset
* | | |0 = corresponding channel n is not reset.
* | | |1 = corresponding channel n is reset.
* @var PDMA_T::REQSEL0_3
* Offset: 0x480 PDMA Request Source Select Register 0
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[6:0] |REQSRC0 |Channel 0 Request Source Selection
* | | |This filed defines which peripheral is connected to PDMA channel 0
* | | |User can configure the peripheral by setting REQSRC0.
* | | |0 = Disable PDMA peripheral request.
* | | |1 = Reserved.
* | | |2 = Channel connects to USB_TX.
* | | |3 = Channel connects to USB_RX.
* | | |4 = Channel connects to UART0_TX.
* | | |5 = Channel connects to UART0_RX.
* | | |6 = Channel connects to UART1_TX.
* | | |7 = Channel connects to UART1_RX.
* | | |8 = Channel connects to UART2_TX.
* | | |9 = Channel connects to UART2_RX.
* | | |10=Channel connects to UART3_TX.
* | | |11 = Channel connects to UART3_RX.
* | | |12 = Channel connects to UART4_TX.
* | | |13 = Channel connects to UART4_RX.
* | | |14 = Channel connects to UART5_TX.
* | | |15 = Channel connects to UART5_RX.
* | | |16 = Channel connects to USCI0_TX.
* | | |17 = Channel connects to USCI0_RX.
* | | |18 = Channel connects to USCI1_TX.
* | | |19 = Channel connects to USCI1_RX.
* | | |20 = Channel connects to SPI0_TX.
* | | |21 = Channel connects to SPI0_RX.
* | | |22 = Channel connects to SPI1_TX.
* | | |23 = Channel connects to SPI1_RX.
* | | |24 = Channel connects to SPI2_TX.
* | | |25 = Channel connects to SPI2_RX.
* | | |26 = Channel connects to SPI3_TX.
* | | |27 = Channel connects to SPI3_RX.
* | | |28 = Channel connects to SPI4_TX.
* | | |29 = Channel connects to SPI4_RX.
* | | |30 = Reserved.
* | | |31 = Reserved.
* | | |32 = Channel connects to PWM0_P1_RX.
* | | |33 = Channel connects to PWM0_P2_RX.
* | | |34 = Channel connects to PWM0_P3_RX.
* | | |35 = Channel connects to PWM1_P1_RX.
* | | |36 = Channel connects to PWM1_P2_RX.
* | | |37 = Channel connects to PWM1_P3_RX.
* | | |38 = Channel connects to I2C0_TX.
* | | |39 = Channel connects to I2C0_RX.
* | | |40 = Channel connects to I2C1_TX.
* | | |41 = Channel connects to I2C1_RX.
* | | |42 = Channel connects to I2C2_TX.
* | | |43 = Channel connects to I2C2_RX.
* | | |44 = Channel connects to I2S0_TX.
* | | |45 = Channel connects to I2S0_RX.
* | | |46 = Channel connects to TMR0.
* | | |47 = Channel connects to TMR1.
* | | |48 = Channel connects to TMR2.
* | | |49 = Channel connects to TMR3.
* | | |50 = Channel connects to ADC_RX.
* | | |51 = Channel connects to DAC0_TX.
* | | |52 = Channel connects to DAC1_TX.
* | | |53 = Channel connects to PWM0_CH0_TX.
* | | |54 = Channel connects to PWM0_CH1_TX.
* | | |55 = Channel connects to PWM0_CH2_TX.
* | | |56 = Channel connects to PWM0_CH3_TX.
* | | |57 = Channel connects to PWM0_CH4_TX.
* | | |58 = Channel connects to PWM0_CH5_TX.
* | | |59 = Channel connects to PWM1_CH0_TX.
* | | |60 = Channel connects to PWM1_CH1_TX.
* | | |61 = Channel connects to PWM1_CH2_TX.
* | | |62 = Channel connects to PWM1_CH3_TX.
* | | |63 = Channel connects to PWM1_CH4_TX.
* | | |64 = Channel connects to PWM1_CH5_TX.
* | | |65 = Channel connects to ETMC_RX.
* | | |Others = Reserved.
* | | |Note 1: A peripheral cannot be assigned to two channels at the same time.
* | | |Note 2: This field is useless when transfer between memory and memory.
* |[14:8] |REQSRC1 |Channel 1 Request Source Selection
* | | |This filed defines which peripheral is connected to PDMA channel 1
* | | |User can configure the peripheral setting by REQSRC1.
* | | |Note: The channel configuration is the same as REQSRC0 field
* | | |Please refer to the explanation of REQSRC0.
* |[22:16] |REQSRC2 |Channel 2 Request Source Selection
* | | |This filed defines which peripheral is connected to PDMA channel 2
* | | |User can configure the peripheral setting by REQSRC2.
* | | |Note: The channel configuration is the same as REQSRC0 field
* | | |Please refer to the explanation of REQSRC0.
* |[30:24] |REQSRC3 |Channel 3 Request Source Selection
* | | |This filed defines which peripheral is connected to PDMA channel 3
* | | |User can configure the peripheral setting by REQSRC3.
* | | |Note: The channel configuration is the same as REQSRC0 field
* | | |Please refer to the explanation of REQSRC0.
* @var PDMA_T::REQSEL4_7
* Offset: 0x484 PDMA Request Source Select Register 1
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[6:0] |REQSRC4 |Channel 4 Request Source Selection
* | | |This filed defines which peripheral is connected to PDMA channel 4
* | | |User can configure the peripheral setting by REQSRC4.
* | | |Note: The channel configuration is the same as REQSRC0 field
* | | |Please refer to the explanation of REQSRC0.
* |[14:8] |REQSRC5 |Channel 5 Request Source Selection
* | | |This filed defines which peripheral is connected to PDMA channel 5
* | | |User can configure the peripheral setting by REQSRC5.
* | | |Note: The channel configuration is the same as REQSRC0 field
* | | |Please refer to the explanation of REQSRC0.
* |[22:16] |REQSRC6 |Channel 6 Request Source Selection
* | | |This filed defines which peripheral is connected to PDMA channel 6
* | | |User can configure the peripheral setting by REQSRC6.
* | | |Note: The channel configuration is the same as REQSRC0 field
* | | |Please refer to the explanation of REQSRC0.
* |[30:24] |REQSRC7 |Channel 7 Request Source Selection
* | | |This filed defines which peripheral is connected to PDMA channel 7
* | | |User can configure the peripheral setting by REQSRC7.
* | | |Note: The channel configuration is the same as REQSRC0 field
* | | |Please refer to the explanation of REQSRC0.
*/
DSCT_T DSCT[8]; /*!< [0x0000 ~ 0x007C] Control Register of PDMA Channel 0 ~ 7 */
/// @cond HIDDEN_SYMBOLS
__I uint32_t RESERVE0[32];
/// @endcond //HIDDEN_SYMBOLS
__I uint32_t CURSCAT[8]; /*!< [0x0100 ~ 0x11c] Current Scatter-gather Descriptor Table Address of PDMA Channel n */
/// @cond HIDDEN_SYMBOLS
__I uint32_t RESERVE1[184];
/// @endcond //HIDDEN_SYMBOLS
__IO uint32_t CHCTL; /*!< [0x0400] PDMA Channel Control Register */
__O uint32_t PAUSE; /*!< [0x0404] PDMA Transfer Pause Control Register */
__O uint32_t SWREQ; /*!< [0x0408] PDMA Software Request Register */
__I uint32_t TRGSTS; /*!< [0x040c] PDMA Channel Request Status Register */
__IO uint32_t PRISET; /*!< [0x0410] PDMA Fixed Priority Setting Register */
__O uint32_t PRICLR; /*!< [0x0414] PDMA Fixed Priority Clear Register */
__IO uint32_t INTEN; /*!< [0x0418] PDMA Interrupt Enable Register */
__IO uint32_t INTSTS; /*!< [0x041c] PDMA Interrupt Status Register */
__IO uint32_t ABTSTS; /*!< [0x0420] PDMA Channel Read/Write Target Abort Flag Register */
__IO uint32_t TDSTS; /*!< [0x0424] PDMA Channel Transfer Done Flag Register */
__IO uint32_t ALIGN; /*!< [0x0428] PDMA Transfer Alignment Status Register */
__I uint32_t TACTSTS; /*!< [0x042c] PDMA Transfer Active Flag Register */
__IO uint32_t TOUTPSC; /*!< [0x0430] PDMA Time-out Prescaler Register */
__IO uint32_t TOUTEN; /*!< [0x0434] PDMA Time-out Enable Register */
__IO uint32_t TOUTIEN; /*!< [0x0438] PDMA Time-out Interrupt Enable Register */
__IO uint32_t SCATBA; /*!< [0x043c] PDMA Scatter-gather Descriptor Table Base Address Register */
__IO uint32_t TOC0_1; /*!< [0x0440] PDMA Time-out Counter Ch1 and Ch0 Register */
/// @cond HIDDEN_SYMBOLS
__I uint32_t RESERVE2[7];
/// @endcond //HIDDEN_SYMBOLS
__IO uint32_t CHRST; /*!< [0x0460] PDMA Channel Reset Register */
/// @cond HIDDEN_SYMBOLS
__I uint32_t RESERVE3[7];
/// @endcond //HIDDEN_SYMBOLS
__IO uint32_t REQSEL0_3; /*!< [0x0480] PDMA Request Source Select Register 0 */
__IO uint32_t REQSEL4_7; /*!< [0x0484] PDMA Request Source Select Register 1 */
/// @cond HIDDEN_SYMBOLS
__I uint32_t RESERVE4[30];
/// @endcond //HIDDEN_SYMBOLS
STRIDE_T STRIDE[6]; /*!< [0x0500 ~ 0x528] Stride Register of PDMA Channel 0 ~ 5 */
} PDMA_T;
/**
@addtogroup PDMA_CONST PDMA Bit Field Definition
Constant Definitions for PDMA Controller
@{ */
#define PDMA_DSCT_CTL_OPMODE_Pos (0) /*!< PDMA_T::DSCT_CTL: OPMODE Position */
#define PDMA_DSCT_CTL_OPMODE_Msk (0x3ul << PDMA_DSCT_CTL_OPMODE_Pos) /*!< PDMA_T::DSCT_CTL: OPMODE Mask */
#define PDMA_DSCT_CTL_TXTYPE_Pos (2) /*!< PDMA_T::DSCT_CTL: TXTYPE Position */
#define PDMA_DSCT_CTL_TXTYPE_Msk (0x1ul << PDMA_DSCT_CTL_TXTYPE_Pos) /*!< PDMA_T::DSCT_CTL: TXTYPE Mask */
#define PDMA_DSCT_CTL_BURSIZE_Pos (4) /*!< PDMA_T::DSCT_CTL: BURSIZE Position */
#define PDMA_DSCT_CTL_BURSIZE_Msk (0x7ul << PDMA_DSCT_CTL_BURSIZE_Pos) /*!< PDMA_T::DSCT_CTL: BURSIZE Mask */
#define PDMA_DSCT_CTL_TBINTDIS_Pos (7) /*!< PDMA_T::DSCT_CTL: TBINTDIS Position */
#define PDMA_DSCT_CTL_TBINTDIS_Msk (0x1ul << PDMA_DSCT_CTL_TBINTDIS_Pos) /*!< PDMA_T::DSCT_CTL: TBINTDIS Mask */
#define PDMA_DSCT_CTL_SAINC_Pos (8) /*!< PDMA_T::DSCT_CTL: SAINC Position */
#define PDMA_DSCT_CTL_SAINC_Msk (0x3ul << PDMA_DSCT_CTL_SAINC_Pos) /*!< PDMA_T::DSCT_CTL: SAINC Mask */
#define PDMA_DSCT_CTL_DAINC_Pos (10) /*!< PDMA_T::DSCT_CTL: DAINC Position */
#define PDMA_DSCT_CTL_DAINC_Msk (0x3ul << PDMA_DSCT_CTL_DAINC_Pos) /*!< PDMA_T::DSCT_CTL: DAINC Mask */
#define PDMA_DSCT_CTL_TXWIDTH_Pos (12) /*!< PDMA_T::DSCT_CTL: TXWIDTH Position */
#define PDMA_DSCT_CTL_TXWIDTH_Msk (0x3ul << PDMA_DSCT_CTL_TXWIDTH_Pos) /*!< PDMA_T::DSCT_CTL: TXWIDTH Mask */
#define PDMA_DSCT_CTL_TXACK_Pos (14) /*!< PDMA_T::DSCT_CTL: TXACK Position */
#define PDMA_DSCT_CTL_TXACK_Msk (0x1ul << PDMA_DSCT_CTL_TXACK_Pos) /*!< PDMA_T::DSCT_CTL: TXACK Mask */
#define PDMA_DSCT_CTL_STRIDE_EN_Pos (15) /*!< PDMA_T::DSCT_CTL: STRIDEEN Position */
#define PDMA_DSCT_CTL_STRIDE_EN_Msk (0x1ul << PDMA_DSCT_CTL_STRIDE_EN_Pos) /*!< PDMA_T::DSCT_CTL: STRIDEEN Mask */
#define PDMA_DSCT_CTL_TXCNT_Pos (16) /*!< PDMA_T::DSCT_CTL: TXCNT Position */
#define PDMA_DSCT_CTL_TXCNT_Msk (0xfffful << PDMA_DSCT_CTL_TXCNT_Pos) /*!< PDMA_T::DSCT_CTL: TXCNT Mask */
#define PDMA_DSCT_SA_SA_Pos (0) /*!< PDMA_T::DSCT_SA: SA Position */
#define PDMA_DSCT_SA_SA_Msk (0xfffffffful << PDMA_DSCT_SA_SA_Pos) /*!< PDMA_T::DSCT_SA: SA Mask */
#define PDMA_DSCT_DA_DA_Pos (0) /*!< PDMA_T::DSCT_DA: DA Position */
#define PDMA_DSCT_DA_DA_Msk (0xfffffffful << PDMA_DSCT_DA_DA_Pos) /*!< PDMA_T::DSCT_DA: DA Mask */
#define PDMA_DSCT_NEXT_NEXT_Pos (0) /*!< PDMA_T::DSCT_NEXT: NEXT Position */
#define PDMA_DSCT_NEXT_NEXT_Msk (0xfffful << PDMA_DSCT_NEXT_NEXT_Pos) /*!< PDMA_T::DSCT_NEXT: NEXT Mask */
#define PDMA_DSCT_NEXT_EXENEXT_Pos (16) /*!< PDMA_T::DSCT_NEXT: EXENEXT Position */
#define PDMA_DSCT_NEXT_EXENEXT_Msk (0xfffful << PDMA_DSCT0_NEXT_EXENEXT_Pos) /*!< PDMA_T::DSCT_NEXT: EXENEXT Mask */
#define PDMA_CURSCAT_CURADDR_Pos (0) /*!< PDMA_T::CURSCAT: CURADDR Position */
#define PDMA_CURSCAT_CURADDR_Msk (0xfffffffful << PDMA_CURSCAT_CURADDR_Pos) /*!< PDMA_T::CURSCAT: CURADDR Mask */
#define PDMA_CHCTL_CHENn_Pos (0) /*!< PDMA_T::CHCTL: CHENn Position */
#define PDMA_CHCTL_CHENn_Msk (0xfful << PDMA_CHCTL_CHENn_Pos) /*!< PDMA_T::CHCTL: CHENn Mask */
#define PDMA_PAUSE_PAUSEn_Pos (0) /*!< PDMA_T::PAUSE: PAUSEn Position */
#define PDMA_PAUSE_PAUSEn_Msk (0xfful << PDMA_PAUSE_PAUSEn_Pos) /*!< PDMA_T::PAUSE: PAUSEn Mask */
#define PDMA_SWREQ_SWREQn_Pos (0) /*!< PDMA_T::SWREQ: SWREQn Position */
#define PDMA_SWREQ_SWREQn_Msk (0xfful << PDMA_SWREQ_SWREQn_Pos) /*!< PDMA_T::SWREQ: SWREQn Mask */
#define PDMA_TRGSTS_REQSTSn_Pos (0) /*!< PDMA_T::TRGSTS: REQSTSn Position */
#define PDMA_TRGSTS_REQSTSn_Msk (0xfful << PDMA_TRGSTS_REQSTSn_Pos) /*!< PDMA_T::TRGSTS: REQSTSn Mask */
#define PDMA_PRISET_FPRISETn_Pos (0) /*!< PDMA_T::PRISET: FPRISETn Position */
#define PDMA_PRISET_FPRISETn_Msk (0xfful << PDMA_PRISET_FPRISETn_Pos) /*!< PDMA_T::PRISET: FPRISETn Mask */
#define PDMA_PRICLR_FPRICLRn_Pos (0) /*!< PDMA_T::PRICLR: FPRICLRn Position */
#define PDMA_PRICLR_FPRICLRn_Msk (0xfful << PDMA_PRICLR_FPRICLRn_Pos) /*!< PDMA_T::PRICLR: FPRICLRn Mask */
#define PDMA_INTEN_INTENn_Pos (0) /*!< PDMA_T::INTEN: INTENn Position */
#define PDMA_INTEN_INTENn_Msk (0xfffful << PDMA_INTEN_INTENn_Pos) /*!< PDMA_T::INTEN: INTENn Mask */
#define PDMA_INTSTS_ABTIF_Pos (0) /*!< PDMA_T::INTSTS: ABTIF Position */
#define PDMA_INTSTS_ABTIF_Msk (0x1ul << PDMA_INTSTS_ABTIF_Pos) /*!< PDMA_T::INTSTS: ABTIF Mask */
#define PDMA_INTSTS_TDIF_Pos (1) /*!< PDMA_T::INTSTS: TDIF Position */
#define PDMA_INTSTS_TDIF_Msk (0x1ul << PDMA_INTSTS_TDIF_Pos) /*!< PDMA_T::INTSTS: TDIF Mask */
#define PDMA_INTSTS_ALIGNF_Pos (2) /*!< PDMA_T::INTSTS: ALIGNF Position */
#define PDMA_INTSTS_ALIGNF_Msk (0x1ul << PDMA_INTSTS_ALIGNF_Pos) /*!< PDMA_T::INTSTS: ALIGNF Mask */
#define PDMA_INTSTS_REQTOF0_Pos (8) /*!< PDMA_T::INTSTS: REQTOF0 Position */
#define PDMA_INTSTS_REQTOF0_Msk (0x1ul << PDMA_INTSTS_REQTOF0_Pos) /*!< PDMA_T::INTSTS: REQTOF0 Mask */
#define PDMA_INTSTS_REQTOF1_Pos (9) /*!< PDMA_T::INTSTS: REQTOF1 Position */
#define PDMA_INTSTS_REQTOF1_Msk (0x1ul << PDMA_INTSTS_REQTOF1_Pos) /*!< PDMA_T::INTSTS: REQTOF1 Mask */
#define PDMA_ABTSTS_ABTIF0_Pos (0) /*!< PDMA_T::ABTSTS: ABTIF0 Position */
#define PDMA_ABTSTS_ABTIF0_Msk (0x1ul << PDMA_ABTSTS_ABTIF0_Pos) /*!< PDMA_T::ABTSTS: ABTIF0 Mask */
#define PDMA_ABTSTS_ABTIF1_Pos (1) /*!< PDMA_T::ABTSTS: ABTIF1 Position */
#define PDMA_ABTSTS_ABTIF1_Msk (0x1ul << PDMA_ABTSTS_ABTIF1_Pos) /*!< PDMA_T::ABTSTS: ABTIF1 Mask */
#define PDMA_ABTSTS_ABTIF2_Pos (2) /*!< PDMA_T::ABTSTS: ABTIF2 Position */
#define PDMA_ABTSTS_ABTIF2_Msk (0x1ul << PDMA_ABTSTS_ABTIF2_Pos) /*!< PDMA_T::ABTSTS: ABTIF2 Mask */
#define PDMA_ABTSTS_ABTIF3_Pos (3) /*!< PDMA_T::ABTSTS: ABTIF3 Position */
#define PDMA_ABTSTS_ABTIF3_Msk (0x1ul << PDMA_ABTSTS_ABTIF3_Pos) /*!< PDMA_T::ABTSTS: ABTIF3 Mask */
#define PDMA_ABTSTS_ABTIF4_Pos (4) /*!< PDMA_T::ABTSTS: ABTIF4 Position */
#define PDMA_ABTSTS_ABTIF4_Msk (0x1ul << PDMA_ABTSTS_ABTIF4_Pos) /*!< PDMA_T::ABTSTS: ABTIF4 Mask */
#define PDMA_ABTSTS_ABTIF5_Pos (5) /*!< PDMA_T::ABTSTS: ABTIF5 Position */
#define PDMA_ABTSTS_ABTIF5_Msk (0x1ul << PDMA_ABTSTS_ABTIF5_Pos) /*!< PDMA_T::ABTSTS: ABTIF5 Mask */
#define PDMA_ABTSTS_ABTIF6_Pos (6) /*!< PDMA_T::ABTSTS: ABTIF6 Position */
#define PDMA_ABTSTS_ABTIF6_Msk (0x1ul << PDMA_ABTSTS_ABTIF6_Pos) /*!< PDMA_T::ABTSTS: ABTIF6 Mask */
#define PDMA_ABTSTS_ABTIF7_Pos (7) /*!< PDMA_T::ABTSTS: ABTIF7 Position */
#define PDMA_ABTSTS_ABTIF7_Msk (0x1ul << PDMA_ABTSTS_ABTIF7_Pos) /*!< PDMA_T::ABTSTS: ABTIF7 Mask */
#define PDMA_TDSTS_TDIF0_Pos (0) /*!< PDMA_T::TDSTS: TDIF0 Position */
#define PDMA_TDSTS_TDIF0_Msk (0x1ul << PDMA_TDSTS_TDIF0_Pos) /*!< PDMA_T::TDSTS: TDIF0 Mask */
#define PDMA_TDSTS_TDIF1_Pos (1) /*!< PDMA_T::TDSTS: TDIF1 Position */
#define PDMA_TDSTS_TDIF1_Msk (0x1ul << PDMA_TDSTS_TDIF1_Pos) /*!< PDMA_T::TDSTS: TDIF1 Mask */
#define PDMA_TDSTS_TDIF2_Pos (2) /*!< PDMA_T::TDSTS: TDIF2 Position */
#define PDMA_TDSTS_TDIF2_Msk (0x1ul << PDMA_TDSTS_TDIF2_Pos) /*!< PDMA_T::TDSTS: TDIF2 Mask */
#define PDMA_TDSTS_TDIF3_Pos (3) /*!< PDMA_T::TDSTS: TDIF3 Position */
#define PDMA_TDSTS_TDIF3_Msk (0x1ul << PDMA_TDSTS_TDIF3_Pos) /*!< PDMA_T::TDSTS: TDIF3 Mask */
#define PDMA_TDSTS_TDIF4_Pos (4) /*!< PDMA_T::TDSTS: TDIF4 Position */
#define PDMA_TDSTS_TDIF4_Msk (0x1ul << PDMA_TDSTS_TDIF4_Pos) /*!< PDMA_T::TDSTS: TDIF4 Mask */
#define PDMA_TDSTS_TDIF5_Pos (5) /*!< PDMA_T::TDSTS: TDIF5 Position */
#define PDMA_TDSTS_TDIF5_Msk (0x1ul << PDMA_TDSTS_TDIF5_Pos) /*!< PDMA_T::TDSTS: TDIF5 Mask */
#define PDMA_TDSTS_TDIF6_Pos (6) /*!< PDMA_T::TDSTS: TDIF6 Position */
#define PDMA_TDSTS_TDIF6_Msk (0x1ul << PDMA_TDSTS_TDIF6_Pos) /*!< PDMA_T::TDSTS: TDIF6 Mask */
#define PDMA_TDSTS_TDIF7_Pos (7) /*!< PDMA_T::TDSTS: TDIF7 Position */
#define PDMA_TDSTS_TDIF7_Msk (0x1ul << PDMA_TDSTS_TDIF7_Pos) /*!< PDMA_T::TDSTS: TDIF7 Mask */
#define PDMA_ALIGN_ALIGNn_Pos (0) /*!< PDMA_T::ALIGN: ALIGNn Position */
#define PDMA_ALIGN_ALIGNn_Msk (0xfful << PDMA_ALIGN_ALIGNn_Pos) /*!< PDMA_T::ALIGN: ALIGNn Mask */
#define PDMA_TACTSTS_TXACTFn_Pos (0) /*!< PDMA_T::TACTSTS: TXACTFn Position */
#define PDMA_TACTSTS_TXACTFn_Msk (0xfful << PDMA_TACTSTS_TXACTFn_Pos) /*!< PDMA_T::TACTSTS: TXACTFn Mask */
#define PDMA_TOUTPSC_TOUTPSC0_Pos (0) /*!< PDMA_T::TOUTPSC: TOUTPSC0 Position */
#define PDMA_TOUTPSC_TOUTPSC0_Msk (0x7ul << PDMA_TOUTPSC_TOUTPSC0_Pos) /*!< PDMA_T::TOUTPSC: TOUTPSC0 Mask */
#define PDMA_TOUTPSC_TOUTPSC1_Pos (4) /*!< PDMA_T::TOUTPSC: TOUTPSC1 Position */
#define PDMA_TOUTPSC_TOUTPSC1_Msk (0x7ul << PDMA_TOUTPSC_TOUTPSC1_Pos) /*!< PDMA_T::TOUTPSC: TOUTPSC1 Mask */
#define PDMA_TOUTEN_TOUTENn_Pos (0) /*!< PDMA_T::TOUTEN: TOUTENn Position */
#define PDMA_TOUTEN_TOUTENn_Msk (0x3ul << PDMA_TOUTEN_TOUTENn_Pos) /*!< PDMA_T::TOUTEN: TOUTENn Mask */
#define PDMA_TOUTIEN_TOUTIENn_Pos (0) /*!< PDMA_T::TOUTIEN: TOUTIENn Position */
#define PDMA_TOUTIEN_TOUTIENn_Msk (0x3ul << PDMA_TOUTIEN_TOUTIENn_Pos) /*!< PDMA_T::TOUTIEN: TOUTIENn Mask */
#define PDMA_SCATBA_SCATBA_Pos (16) /*!< PDMA_T::SCATBA: SCATBA Position */
#define PDMA_SCATBA_SCATBA_Msk (0xfffful << PDMA_SCATBA_SCATBA_Pos) /*!< PDMA_T::SCATBA: SCATBA Mask */
#define PDMA_TOC0_1_TOC0_Pos (0) /*!< PDMA_T::TOC0_1: TOC0 Position */
#define PDMA_TOC0_1_TOC0_Msk (0xfffful << PDMA_TOC0_1_TOC0_Pos) /*!< PDMA_T::TOC0_1: TOC0 Mask */
#define PDMA_TOC0_1_TOC1_Pos (16) /*!< PDMA_T::TOC0_1: TOC1 Position */
#define PDMA_TOC0_1_TOC1_Msk (0xfffful << PDMA_TOC0_1_TOC1_Pos) /*!< PDMA_T::TOC0_1: TOC1 Mask */
#define PDMA_CHRST_CHnRST_Pos (0) /*!< PDMA_T::CHRST: CHnRST Position */
#define PDMA_CHRST_CHnRST_Msk (0xfffful << PDMA_CHRST_CHnRST_Pos) /*!< PDMA_T::CHRST: CHnRST Mask */
#define PDMA_REQSEL0_3_REQSRC0_Pos (0) /*!< PDMA_T::REQSEL0_3: REQSRC0 Position */
#define PDMA_REQSEL0_3_REQSRC0_Msk (0x7ful << PDMA_REQSEL0_3_REQSRC0_Pos) /*!< PDMA_T::REQSEL0_3: REQSRC0 Mask */
#define PDMA_REQSEL0_3_REQSRC1_Pos (8) /*!< PDMA_T::REQSEL0_3: REQSRC1 Position */
#define PDMA_REQSEL0_3_REQSRC1_Msk (0x7ful << PDMA_REQSEL0_3_REQSRC1_Pos) /*!< PDMA_T::REQSEL0_3: REQSRC1 Mask */
#define PDMA_REQSEL0_3_REQSRC2_Pos (16) /*!< PDMA_T::REQSEL0_3: REQSRC2 Position */
#define PDMA_REQSEL0_3_REQSRC2_Msk (0x7ful << PDMA_REQSEL0_3_REQSRC2_Pos) /*!< PDMA_T::REQSEL0_3: REQSRC2 Mask */
#define PDMA_REQSEL0_3_REQSRC3_Pos (24) /*!< PDMA_T::REQSEL0_3: REQSRC3 Position */
#define PDMA_REQSEL0_3_REQSRC3_Msk (0x7ful << PDMA_REQSEL0_3_REQSRC3_Pos) /*!< PDMA_T::REQSEL0_3: REQSRC3 Mask */
#define PDMA_REQSEL4_7_REQSRC4_Pos (0) /*!< PDMA_T::REQSEL4_7: REQSRC4 Position */
#define PDMA_REQSEL4_7_REQSRC4_Msk (0x7ful << PDMA_REQSEL4_7_REQSRC4_Pos) /*!< PDMA_T::REQSEL4_7: REQSRC4 Mask */
#define PDMA_REQSEL4_7_REQSRC5_Pos (8) /*!< PDMA_T::REQSEL4_7: REQSRC5 Position */
#define PDMA_REQSEL4_7_REQSRC5_Msk (0x7ful << PDMA_REQSEL4_7_REQSRC5_Pos) /*!< PDMA_T::REQSEL4_7: REQSRC5 Mask */
#define PDMA_REQSEL4_7_REQSRC6_Pos (16) /*!< PDMA_T::REQSEL4_7: REQSRC6 Position */
#define PDMA_REQSEL4_7_REQSRC6_Msk (0x7ful << PDMA_REQSEL4_7_REQSRC6_Pos) /*!< PDMA_T::REQSEL4_7: REQSRC6 Mask */
#define PDMA_REQSEL4_7_REQSRC7_Pos (24) /*!< PDMA_T::REQSEL4_7: REQSRC7 Position */
#define PDMA_REQSEL4_7_REQSRC7_Msk (0x7ful << PDMA_REQSEL4_7_REQSRC7_Pos) /*!< PDMA_T::REQSEL4_7: REQSRC7 Mask */
#define PDMA_STCR_STC_Pos (0) /*!< PDMA_T::STCR: STC Position */
#define PDMA_STCR_STC_Msk (0xfffful << PDMA_STCR_STC_Pos) /*!< PDMA_T::STCR: STC Mask */
#define PDMA_ASOCR_SASOL_Pos (0) /*!< PDMA_T::ASOCR: SASOL Position */
#define PDMA_ASOCR_SASOL_Msk (0xfffful << PDMA_ASOCR_SASOL_Pos) /*!< PDMA_T::ASOCR: SASOL Mask */
#define PDMA_ASOCR_DASOL_Pos (16) /*!< PDMA_T::ASOCR: DASOL Position */
#define PDMA_ASOCR_DASOL_Msk (0xfffful << PDMA_ASOCR_DASOL_Pos) /*!< PDMA_T::ASOCR: DASOL Mask */
/** @} PDMA_CONST */
/** @} end of PDMA register group */
/** @} end of REGISTER group */
#if defined ( __CC_ARM )
#pragma no_anon_unions
#endif
#endif /* __PDMA_REG_H__ */
Reference in New Issue View Git Blame Copy Permalink