Macintosh-SW/mac-rom-simm-programmer
1
0
Fork 0
mirror of https://github.com/dougg3/mac-rom-simm-programmer.git synced 2024-11-29 21:49:19 +00:00
Code Issues Projects Releases Wiki Activity
7a77d583da
mac-rom-simm-programmer/hal/m258ke/nuvoton/sc_reg.h

977 lines
78 KiB
C
Raw Blame History

/**************************************************************************//**
* @file sc_reg.h
* @version V1.00
* @brief SC register definition header file
*
* SPDX-License-Identifier: Apache-2.0
* @copyright (C) 2019 Nuvoton Technology Corp. All rights reserved.
*****************************************************************************/
#ifndef __SC_REG_H__
#define __SC_REG_H__
#if defined ( __CC_ARM )
#pragma anon_unions
#endif
/**
@addtogroup REGISTER Control Register
@{
*/
/**
@addtogroup SC Smart Card Host Interface Controller (SC)
Memory Mapped Structure for SC Controller
@{
*/
typedef struct
{
/**
* @var SC_T::DAT
* Offset: 0x00 SC Receive/Transmit Holding Buffer Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |DAT |Receive/Transmit Holding Buffer
* | | |Write Operation:
* | | |By writing data to DAT, the SC will send out an 8-bit data.
* | | |Note: If SCEN (SCn_CTL[0]) is not enabled, DAT cannot be programmed.
* | | |Read Operation:
* | | |By reading DAT, the SC will return an 8-bit received data.
* @var SC_T::CTL
* Offset: 0x04 SC Control Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[0] |SCEN |SC Controller Enable Bit
* | | |Set this bit to 1 to enable SC operation. If this bit is cleared,
* | | |0 = SC will force all transition to IDLE state.
* | | |1 = SC controller is enabled and all function can work correctly.
* | | |Note: SCEN must be set to 1 before filling in other SC registers, or smart card will not work properly.
* |[1] |RXOFF |RX Transition Disable Control Bit
* | | |This bit is used for disable Rx transition function.
* | | |0 = The receiver Enabled.
* | | |1 = The receiver Disabled.
* | | |Note: If AUTOCEN (SCn_CTL[3]) is enabled, this field is ignored.
* |[2] |TXOFF |TX Transition Disable Control Bit
* | | |This bit is used for disable Tx transition function.
* | | |0 = The transceiver Enabled.
* | | |1 = The transceiver Disabled.
* |[3] |AUTOCEN |Auto Convention Enable Bit
* | | |This bit is used for enable auto convention function.
* | | |0 = Auto-convention Disabled.
* | | |1 = Auto-convention Enabled.
* | | |If user enables auto convention function, the setting step must be done before Answer to Reset (ATR) state and the first data must be 0x3B or 0x3F
* | | |After hardware received first data and stored it at buffer, hardware will decided the convention and change the CONSEL (SCn_CTL[5:4]) bits automatically when received first data is 0x3B or 0x3F
* | | |If received first byte is 0x3B, TS is direct convention, CONSEL (SCn_CTL[5:4]) will be set to 00 automatically, otherwise the TS is inverse convention, and CONSEL (SCn_CTL[5:4]) will be set to 11.
* | | |If the first data is not 0x3B or 0x3F, hardware will set ACERRIF (SCn_INTSTS[10]) and generate an interrupt to CPU when ACERRIEN (SCn_INTEN[10]) is enabled.
* |[5:4] |CONSEL |Convention Selection
* | | |00 = Direct convention.
* | | |01 = Reserved.
* | | |10 = Reserved.
* | | |11 = Inverse convention.
* | | |Note: If AUTOCEN (SCn_CTL[3]) is enabled, this field is ignored.
* |[7:6] |RXTRGLV |Rx Buffer Trigger Level
* | | |When the number of bytes in the receiving buffer equals the RXTRGLV, the RDAIF will be set
* | | |If RDAIEN (SCn_INTEN[0]) is enabled, an interrupt will be generated to CPU.
* | | |00 = Rx Buffer Trigger Level with 01 bytes.
* | | |01 = Rx Buffer Trigger Level with 02 bytes.
* | | |10 = Rx Buffer Trigger Level with 03 bytes.
* | | |11 = Reserved.
* |[12:8] |BGT |Block Guard Time (BGT)
* | | |Block guard time means the minimum interval between the leading edges of two consecutive characters between different transfer directions
* | | |This field indicates the counter for the bit length of block guard time
* | | |According to ISO 7816-3, in T = 0 mode, user must fill 15 (real block guard time = 16.5) to this field; in T = 1 mode, user must fill 21 (real block guard time = 22.5) to it.
* | | |Note: The real block guard time is BGT + 1.
* |[14:13] |TMRSEL |Timer Channel Selection
* | | |00 = All internal timer function Disabled.
* | | |11 = Internal 24 bit timer and two 8 bit timers Enabled
* | | |User can configure them by setting SCn_TMRCTL0[23:0], SCn_TMRCTL1[7:0] and SCn_TMRCTL2[7:0].
* | | |Other configurations are reserved
* |[15] |NSB |Stop Bit Length
* | | |This field indicates the length of stop bit.
* | | |0 = The stop bit length is 2 ETU.
* | | |1= The stop bit length is 1 ETU.
* | | |Note1: The default stop bit length is 2. SC and UART adopts NSB to program the stop bit length.
* | | |Note2: In UART mode, RX can receive the data sequence in 1 stop bit or 2 stop bits with NSB is set to 0.
* |[18:16] |RXRTY |RX Error Retry Count Number
* | | |This field indicates the maximum number of receiver retries that are allowed when parity error has occurred
* | | |Note1: The real retry number is RXRTY + 1, so 8 is the maximum retry number.
* | | |Note2: This field cannot be changed when RXRTYEN enabled
* | | |The change flow is to disable RXRTYEN first and then fill in new retry value.
* |[19] |RXRTYEN |RX Error Retry Enable Bit
* | | |This bit enables receiver retry function when parity error has occurred.
* | | |0 = RX error retry function Disabled.
* | | |1 = RX error retry function Enabled.
* | | |Note: User must fill in the RXRTY value before enabling this bit.
* |[22:20] |TXRTY |TX Error Retry Count Number
* | | |This field indicates the maximum number of transmitter retries that are allowed when parity error has occurred.
* | | |Note1: The real retry number is TXRTY + 1, so 8 is the maximum retry number.
* | | |Note2: This field cannot be changed when TXRTYEN enabled
* | | |The change flow is to disable TXRTYEN first and then fill in new retry value.
* |[23] |TXRTYEN |TX Error Retry Enable Bit
* | | |This bit enables transmitter retry function when parity error has occurred.
* | | |0 = TX error retry function Disabled.
* | | |1 = TX error retry function Enabled.
* |[25:24] |CDDBSEL |Card Detect De-bounce Selection
* | | |This field indicates the card detect de-bounce selection.
* | | |00 = De-bounce sample card insert once per 384 (128 * 3) SC module clocks and de-bounce sample card removal once per 128 SC module clocks.
* | | |Other configurations are reserved.
* |[26] |CDLV |Card Detect Level Selection
* | | |0 = When hardware detects the card detect pin (SCn_CD) from high to low, it indicates a card is detected.
* | | |1 = When hardware detects the card detect pin (SCn_CD) from low to high, it indicates a card is detected.
* | | |Note: User must select card detect level before Smart Card controller enabled.
* |[30] |SYNC |SYNC Flag Indicator (Read Only)
* | | |Due to synchronization, user should check this bit before writing a new value to RXRTY and TXRTY fields.
* | | |0 = Synchronizing is completion, user can write new data to RXRTY and TXRTY.
* | | |1 = Last value is synchronizing.
* @var SC_T::ALTCTL
* Offset: 0x08 SC Alternate Control Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[0] |TXRST |TX Software Reset
* | | |When TXRST is set, all the bytes in the transmit buffer and TX internal state machine will be cleared.
* | | |0 = No effect.
* | | |1 = Reset the TX internal state machine and pointers.
* | | |Note: This bit will be auto cleared after reset is complete.
* |[1] |RXRST |Rx Software Reset
* | | |When RXRST is set, all the bytes in the receive buffer and Rx internal state machine will be cleared.
* | | |0 = No effect.
* | | |1 = Reset the Rx internal state machine and pointers.
* | | |Note: This bit will be auto cleared after reset is complete.
* |[2] |DACTEN |Deactivation Sequence Generator Enable Bit
* | | |This bit enables SC controller to initiate the card by deactivation sequence.
* | | |0 = No effect.
* | | |1 = Deactivation sequence generator Enabled.
* | | |Note1: When the deactivation sequence completed, this bit will be cleared automatically and the INITIF (SCn_INTSTS[8]) will be set to 1.
* | | |Note2: This field will be cleared by TXRST (SCn_ALTCTL[0]) and RXRST (SCn_ALTCTL[1])
* | | |Thus, do not fill in this bit DACTEN, TXRST and RXRST at the same time.
* | | |Note3: If SCEN (SCn_CTL[0]) is not enabled, this filed cannot be programmed.
* |[3] |ACTEN |Activation Sequence Generator Enable Bit
* | | |This bit enables SC controller to initiate the card by activation sequence.
* | | |0 = No effect.
* | | |1 = Activation sequence generator Enabled.
* | | |Note1: When the activation sequence completed, this bit will be cleared automatically and the INITIF (SCn_INTSTS[8]) will be set to 1.
* | | |Note2: This field will be cleared by TXRST (SCn_ALTCTL[0]) and RXRST (SCn_ALTCTL[1])
* | | |Thus, do not fill in this bit ACTEN, TXRST and RXRST at the same time.
* | | |Note3: If SCEN (SCn_CTL[0]) is not enabled, this filed cannot be programmed.
* | | |Note4: During the activation sequence, RX is disabled automatically and can not receive data
* | | |After the activation sequence completion, RXOFF (SCn_CTL[1]) keeps the state before hardware activation.
* |[4] |WARSTEN |Warm Reset Sequence Generator Enable Bit
* | | |This bit enables SC controller to initiate the card by warm reset sequence.
* | | |0 = No effect.
* | | |1 = Warm reset sequence generator Enabled.
* | | |Note1: When the warm reset sequence completed, this bit will be cleared automatically and the INITIF (SCn_INTSTS[8]) will be set to 1.
* | | |Note2: This field will be cleared by TXRST (SCn_ALTCTL[0]) and RXRST (SCn_ALTCTL[1])
* | | |Thus, do not fill in this bit WARSTEN, TXRST and RXRST at the same time.
* | | |Note3: If SCEN (SCn_CTL[0]) is not enabled, this filed cannot be programmed.
* | | |Note4: During the warm reset sequence, RX is disabled automatically and can not receive data
* | | |After the warm reset sequence completion, RXOFF (SCn_CTL[1]) keeps the state before perform warm reset sequence.
* |[5] |CNTEN0 |Internal Timer0 Start Enable Bit
* | | |This bit enables Timer 0 to start counting
* | | |User can fill 0 to stop it and set 1 to reload and count
* | | |The counter unit is ETU base.
* | | |0 = Stops counting.
* | | |1 = Start counting.
* | | |Note1: This field is used for internal 24 bit timer when TMRSEL (SCn_CTL[14:13]) is 11 only.
* | | |Note2: If the operation mode is not in auto-reload mode (SCn_TMRCTL0[26] = 0), this bit will be auto-cleared by hardware.
* | | |Note3: If SCEN (SCn_CTL[0]) is not enabled, this filed cannot be programmed.
* |[6] |CNTEN1 |Internal Timer1 Start Enable Bit
* | | |This bit enables Timer 1 to start counting
* | | |User can fill 0 to stop it and set 1 to reload and count
* | | |The counter unit is ETU base.
* | | |0 = Stops counting.
* | | |1 = Start counting.
* | | |Note1: This field is used for internal 8 bit timer when TMRSEL(SCn_CTL[14:13]) is 11 only
* | | |Do not fill CNTEN1 when TMRSEL (SCn_CTL[14:13]) is not equal to 11.
* | | |Note2: If the operation mode is not in auto-reload mode (SCn_TMRCTL1[26] = 0), this bit will be auto-cleared by hardware.
* | | |Note3: If SCEN (SCn_CTL[0]) is not enabled, this filed cannot be programmed.
* |[7] |CNTEN2 |Internal Timer2 Start Enable Bit
* | | |This bit enables Timer 2 to start counting
* | | |User can fill 0 to stop it and set 1 to reload and count
* | | |The counter unit is ETU base.
* | | |0 = Stops counting.
* | | |1 = Start counting.
* | | |Note1: This field is used for internal 8 bit timer when TMRSEL (SCn_CTL[14:13]) is 11 only
* | | |Do not fill in CNTEN2 when TMRSEL (SCn_CTL[14:13]) is not equal to 11.
* | | |Note2: If the operation mode is not in auto-reload mode (SCn_TMRCTL2[26] = 0), this bit will be auto-cleared by hardware.
* | | |Note3: If SCEN (SCn_CTL[0]) is not enabled, this filed cannot be programmed.
* |[9:8] |INITSEL |Initial Timing Selection
* | | |This fields indicates the initial timing of hardware activation, warm-reset or deactivation.
* | | |The unit of initial timing is SC module clock.
* | | |Activation: refer to SC Activation Sequence in Figure 7.14-54.
* | | |Warm-reset: refer to Warm-Reset Sequence in Figure 7.14-5.
* | | |Deactivation: refer to Deactivation Sequence in Figure 7.14-56.
* | | |Note: When set activation and warm reset in Timer0 operation mode 0011, it may have deviation at most 128 SC module clock cycles.
* |[11] |ADACEN |Auto Deactivation When Card Removal
* | | |This bit is used for enable hardware auto deactivation when smart card is removed.
* | | |0 = Auto deactivation Disabled.
* | | |1 = Auto deactivation Enabled.
* | | |Note: When the card is removed, hardware will stop any process and then do deactivation sequence if this bit is set
* | | |If auto deactivation process completes, hardware will set INITIF (SCn_INTSTS[8]) also.
* |[12] |RXBGTEN |Receiver Block Guard Time Function Enable Bit
* | | |This bit enables the receiver block guard time function.
* | | |0 = Receiver block guard time function Disabled.
* | | |1 = Receiver block guard time function Enabled.
* |[13] |ACTSTS0 |Internal Timer0 Active Status (Read Only)
* | | |This bit indicates the timer counter status of timer0.
* | | |0 = Timer0 is not active.
* | | |1 = Timer0 is active.
* | | |Note: Timer0 is active does not always mean timer0 is counting the CNT (SCn_TMRCTL0[23:0]).
* |[14] |ACTSTS1 |Internal Timer1 Active Status (Read Only)
* | | |This bit indicates the timer counter status of timer1.
* | | |0 = Timer1 is not active.
* | | |1 = Timer1 is active.
* | | |Note: Timer1 is active does not always mean timer1 is counting the CNT (SCn_TMRCTL1[7:0]).
* |[15] |ACTSTS2 |Internal Timer2 Active Status (Read Only)
* | | |This bit indicates the timer counter status of timer2.
* | | |0 = Timer2 is not active.
* | | |1 = Timer2 is active.
* | | |Note: Timer2 is active does not always mean timer2 is counting the CNT (SCn_TMRCTL2[7:0]).
* |[31] |SYNC |SYNC Flag Indicator (Read Only)
* | | |Due to synchronization, user should check this bit when writing a new value to SCn_ALTCTL register.
* | | |0 = Synchronizing is completion, user can write new data to SCn_ALTCTL register.
* | | |1 = Last value is synchronizing.
* @var SC_T::EGT
* Offset: 0x0C SC Extra Guard Time Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |EGT |Extra Guard Time
* | | |This field indicates the extra guard time value.
* | | |Note: The extra guard time unit is ETU base.
* @var SC_T::RXTOUT
* Offset: 0x10 SC Receive Buffer Time-out Counter Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[8:0] |RFTM |SC Receiver FIFO Time-out Counter
* | | |The time-out down counter resets and starts counting whenever the RX buffer received a new data
* | | |Once the counter decrease to 1 and no new data is received or CPU does not read data by reading SCn_DAT, a receiver time-out flag RXTOIF (SCn_INTSTS[9]) will be set, and hardware will generate an interrupt to CPU when RXTOIEN (SCn_INTEN[9]) is enabled.
* | | |Note1: The counter unit is ETU based and the interval of time-out is RFTM + 0.5.
* | | |Note2: Filling in all 0 to this field indicates to disable this function.
* @var SC_T::ETUCTL
* Offset: 0x14 SC Element Time Unit Control Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[11:0] |ETURDIV |ETU Rate Divider
* | | |The field is used for ETU clock rate divider.
* | | |The real ETU is ETURDIV + 1.
* | | |Note: User can configure this field, but this field must be greater than 0x04.
* @var SC_T::INTEN
* Offset: 0x18 SC Interrupt Enable Control Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[0] |RDAIEN |Receive Data Reach Interrupt Enable Bit
* | | |This field is used to enable received data reaching trigger level RXTRGLV (SCn_CTL[7:6]) interrupt.
* | | |0 = Receive data reach trigger level interrupt Disabled.
* | | |1 = Receive data reach trigger level interrupt Enabled.
* |[1] |TBEIEN |Transmit Buffer Empty Interrupt Enable Bit
* | | |This field is used to enable transmit buffer empty interrupt.
* | | |0 = Transmit buffer empty interrupt Disabled.
* | | |1 = Transmit buffer empty interrupt Enabled.
* |[2] |TERRIEN |Transfer Error Interrupt Enable Bit
* | | |This field is used to enable transfer error interrupt
* | | |The transfer error states is at SCn_STATUS register which includes receiver break error BEF (SCn_STATUS[6]), frame error FEF (SCn_STATUS[5]), parity error PEF (SCn_STATUS[4]), receive buffer overflow error RXOV (SCn_STATUS[0]), transmit buffer overflow error TXOV (SCn_STATUS[8]), receiver retry over limit error RXOVERR (SCn_STATUS[22]) and transmitter retry over limit error TXOVERR (SCn_STATUS[30]).
* | | |0 = Transfer error interrupt Disabled.
* | | |1 = Transfer error interrupt Enabled.
* |[3] |TMR0IEN |Timer0 Interrupt Enable Bit
* | | |This field is used to enable Timer0 interrupt function.
* | | |0 = Timer0 interrupt Disabled.
* | | |1 = Timer0 interrupt Enabled.
* |[4] |TMR1IEN |Timer1 Interrupt Enable Bit
* | | |This field is used to enable the Timer1 interrupt function.
* | | |0 = Timer1 interrupt Disabled.
* | | |1 = Timer1 interrupt Enabled.
* |[5] |TMR2IEN |Timer2 Interrupt Enable Bit
* | | |This field is used to enable Timer2 interrupt function.
* | | |0 = Timer2 interrupt Disabled.
* | | |1 = Timer2 interrupt Enabled.
* |[6] |BGTIEN |Block Guard Time Interrupt Enable Bit
* | | |This field is used to enable block guard time interrupt in receive direction.
* | | |0 = Block guard time interrupt Disabled.
* | | |1 = Block guard time interrupt Enabled.
* | | |Note: This bit is valid only for receive direction block guard time.
* |[7] |CDIEN |Card Detect Interrupt Enable Bit
* | | |This field is used to enable card detect interrupt
* | | |The card detect status is CDPINSTS (SCn_STATUS[13]).
* | | |0 = Card detect interrupt Disabled.
* | | |1 = Card detect interrupt Enabled.
* |[8] |INITIEN |Initial End Interrupt Enable Bit
* | | |This field is used to enable activation (ACTEN (SCn_ALTCTL[3] = 1)), deactivation (DACTEN (SCn_ALTCTL[2] = 1)) and warm reset (WARSTEN (SCn_ALTCTL [4])) sequence complete interrupt.
* | | |0 = Initial end interrupt Disabled.
* | | |1 = Initial end interrupt Enabled.
* |[9] |RXTOIEN |Receiver Buffer Time-out Interrupt Enable Bit
* | | |This field is used to enable receiver buffer time-out interrupt.
* | | |0 = Receiver buffer time-out interrupt Disabled.
* | | |1 = Receiver buffer time-out interrupt Enabled.
* |[10] |ACERRIEN |Auto Convention Error Interrupt Enable Bit
* | | |This field is used to enable auto-convention error interrupt.
* | | |0 = Auto-convention error interrupt Disabled.
* | | |1 = Auto-convention error interrupt Enabled.
* @var SC_T::INTSTS
* Offset: 0x1C SC Interrupt Status Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[0] |RDAIF |Receive Data Reach Interrupt Status Flag (Read Only)
* | | |This field is used for received data reaching trigger level RXTRGLV (SCn_CTL[7:6]) interrupt status flag.
* | | |0 = Number of receive buffer is less than RXTRGLV setting.
* | | |1 = Number of receive buffer data equals the RXTRGLV setting.
* | | |Note: This bit is read only
* | | |If user reads data from SCn_DAT and receiver buffer data byte number is less than RXTRGLV, this bit will be cleared automatically.
* |[1] |TBEIF |Transmit Buffer Empty Interrupt Status Flag (Read Only)
* | | |This field is used for transmit buffer empty interrupt status flag.
* | | |0 = Transmit buffer is not empty.
* | | |1 = Transmit buffer is empty.
* | | |Note: This bit is read only
* | | |If user wants to clear this bit, user must write data to DAT (SCn_DAT[7:0]) and then this bit will be cleared automatically.
* |[2] |TERRIF |Transfer Error Interrupt Status Flag
* | | |This field is used for transfer error interrupt status flag
* | | |The transfer error states is at SCn_STATUS register which includes receiver break error BEF (SCn_STATUS[6]), frame error FEF (SCn_STATUS[5], parity error PEF (SCn_STATUS[4] and receive buffer overflow error RXOV (SCn_STATUS[0]), transmit buffer overflow error TXOV (SCn_STATUS[8]), receiver retry over limit error RXOVERR (SCn_STATUS[22] or transmitter retry over limit error TXOVERR (SCn_STATUS[30]).
* | | |0 = Transfer error interrupt did not occur.
* | | |1 = Transfer error interrupt occurred.
* | | |Note1: This field is the status flag of BEF, FEF, PEF, RXOV, TXOV, RXOVERR or TXOVERR.
* | | |Note2: This bit can be cleared by writing 1 to it.
* |[3] |TMR0IF |Timer0 Interrupt Status Flag
* | | |This field is used for Timer0 interrupt status flag.
* | | |0 = Timer0 interrupt did not occur.
* | | |1 = Timer0 interrupt occurred.
* | | |Note: This bit can be cleared by writing 1 to it.
* |[4] |TMR1IF |Timer1 Interrupt Status Flag
* | | |This field is used for Timer1 interrupt status flag.
* | | |0 = Timer1 interrupt did not occur.
* | | |1 = Timer1 interrupt occurred.
* | | |Note: This bit can be cleared by writing 1 to it.
* |[5] |TMR2IF |Timer2 Interrupt Status Flag
* | | |This field is used for Timer2 interrupt status flag.
* | | |0 = Timer2 interrupt did not occur.
* | | |1 = Timer2 interrupt occurred.
* | | |Note: This bit can be cleared by writing 1 to it.
* |[6] |BGTIF |Block Guard Time Interrupt Status Flag
* | | |This field is used for indicate block guard time interrupt status flag in receive direction.
* | | |0 = Block guard time interrupt did not occur.
* | | |1 = Block guard time interrupt occurred.
* | | |Note1: This bit is valid only when RXBGTEN (SCn_ALTCTL[12]) is enabled.
* | | |Note2: This bit can be cleared by writing 1 to it.
* |[7] |CDIF |Card Detect Interrupt Status Flag (Read Only)
* | | |This field is used for card detect interrupt status flag
* | | |The card detect status is CINSERT (SCn_STATUS[12]) and CREMOVE (SCn_STATUS[11]).
* | | |0 = Card detect event did not occur.
* | | |1 = Card detect event occurred.
* | | |Note: This bit is read only, user must to clear CINSERT or CREMOVE status to clear it.
* |[8] |INITIF |Initial End Interrupt Status Flag
* | | |This field is used for activation (ACTEN (SCn_ALTCTL[3])), deactivation (DACTEN (SCn_ALTCTL[2])) and warm reset (WARSTEN (SCn_ALTCTL[4])) sequence interrupt status flag.
* | | |0 = Initial sequence is not complete.
* | | |1 = Initial sequence is completed.
* | | |Note: This bit can be cleared by writing 1 to it.
* |[9] |RXTOIF |Receive Buffer Time-out Interrupt Status Flag (Read Only)
* | | |This field is used for indicate receive buffer time-out interrupt status flag.
* | | |0 = Receive buffer time-out interrupt did not occur.
* | | |1 = Receive buffer time-out interrupt occurred.
* | | |Note: This bit is read only, user must read all receive buffer remaining data by reading SCn_DAT register to clear it.
* |[10] |ACERRIF |Auto Convention Error Interrupt Status Flag
* | | |This field indicates auto convention sequence error.
* | | |0 = Received TS at ATR state is 0x3B or 0x3F.
* | | |1 = Received TS at ATR state is neither 0x3B nor 0x3F.
* | | |Note: This bit can be cleared by writing 1 to it.
* @var SC_T::STATUS
* Offset: 0x20 SC Transfer Status Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[0] |RXOV |Receive Overflow Error Status Flag
* | | |This bit is set when Rx buffer overflow.
* | | |0 = Rx buffer is not overflow.
* | | |1 = Rx buffer is overflow when the number of received bytes is greater than Rx buffer size (4 bytes).
* | | |Note: This bit can be cleared by writing 1 to it.
* |[1] |RXEMPTY |Receive Buffer Empty Status Flag (Read Only)
* | | |This bit indicates Rx buffer empty or not.
* | | |0 = Rx buffer is not empty.
* | | |1 = Rx buffer is empty, it means the last byte of Rx buffer has read from DAT (SCn_DAT[7:0]) by CPU.
* |[2] |RXFULL |Receive Buffer Full Status Flag (Read Only)
* | | |This bit indicates Rx buffer full or not.
* | | |0 = Rx buffer count is less than 4.
* | | |1 = Rx buffer count equals to 4.
* |[4] |PEF |Receiver Parity Error Status Flag
* | | |This bit is set to logic 1 whenever the received character does not have a valid "parity bit".
* | | |0 = Receiver parity error flag did not occur.
* | | |1 = Receiver parity error flag occurred.
* | | |Note1: This bit can be cleared by writing 1 to it.
* | | |Note2: If CPU sets receiver retries function by setting RXRTYEN (SCn_CTL[19]), hardware will not set this flag.
* |[5] |FEF |Receiver Frame Error Status Flag
* | | |This bit is set to logic 1 whenever the received character does not have a valid "stop bit" (that is, the stop bit following the last data bit or parity bit is detected as logic 0).
* | | |0 = Receiver frame error flag did not occur.
* | | |1 = Receiver frame error flag occurred.
* | | |Note1: This bit can be cleared by writing 1 to it.
* | | |Note2: If CPU sets receiver retries function by setting RXRTYEN (SCn_CTL[19]), hardware will not set this flag.
* |[6] |BEF |Receiver Break Error Status Flag
* | | |This bit is set to logic 1 whenever the received data input (Rx) held in the "spacing state" (logic 0) is longer than a full word transmission time (that is, the total time of "start bit" + "data bits" + "parity bit" + "stop bits").
* | | |0 = Receiver break error flag did not occur.
* | | |1 = Receiver break error flag occurred.
* | | |Note1: This bit can be cleared by writing 1 to it.
* | | |Note2: If CPU sets receiver retries function by setting RXRTYEN (SCn_CTL[19]), hardware will not set this flag.
* |[8] |TXOV |Transmit Overflow Error Interrupt Status Flag
* | | |This bit is set when Tx buffer overflow.
* | | |0 = Tx buffer is not overflow.
* | | |1 = Tx buffer is overflow when Tx buffer is full and an additional write operation to DAT (SCn_DAT[7:0]).
* | | |Note: This bit can be cleared by writing 1 to it.
* |[9] |TXEMPTY |Transmit Buffer Empty Status Flag (Read Only)
* | | |This bit indicates TX buffer empty or not.
* | | |0 = Tx buffer is not empty.
* | | |1 = Tx buffer is empty, it means the last byte of Tx buffer has been transferred to Transmitter Shift Register.
* | | |Note: This bit will be cleared when writing data into DAT (SCn_DAT[7:0]).
* |[10] |TXFULL |Transmit Buffer Full Status Flag (Read Only)
* | | |This bit indicates Tx buffer full or not.
* | | |0 = Tx buffer count is less than 4.
* | | |1 = Tx buffer count equals to 4.
* |[11] |CREMOVE |Card Removal Status of SCn_CD Pin
* | | |This bit is set whenever card has been removal.
* | | |0 = No effect.
* | | |1 = Card removed.
* | | |Note1: This bit can be cleared by writing "1" to it.
* | | |Note2: Card detect function will start after SCEN (SCn_CTL[0]) set.
* |[12] |CINSERT |Card Insert Status of SCn_CD Pin
* | | |This bit is set whenever card has been inserted.
* | | |0 = No effect.
* | | |1 = Card insert.
* | | |Note1: This bit can be cleared by writing "1" to it.
* | | |Note2: The card detect function will start after SCEN (SCn_CTL[0]) set.
* |[13] |CDPINSTS |Card Detect Pin Status (Read Only)
* | | |This bit is the pin status of SCn_CD.
* | | |0 = The SCn_CD pin state at low.
* | | |1 = The SCn_CD pin state at high.
* |[18:16] |RXPOINT |Receive Buffer Pointer Status (Read Only)
* | | |This field indicates the Rx buffer pointer status
* | | |When SC controller receives one byte from external device, RXPOINT increases one
* | | |When one byte of Rx buffer is read by CPU, RXPOINT decreases one.
* |[21] |RXRERR |Receiver Retry Error
* | | |This bit is used for receiver error retry and set by hardware.
* | | |0 = No Rx retry transfer.
* | | |1 = Rx has any error and retries transfer.
* | | |Note1: This bit can be cleared by writing 1 to it.
* | | |Note2 This bit is a flag and cannot generate any interrupt to CPU.
* | | |Note3: If CPU enables receiver retries function by setting RXRTYEN (SCn_CTL[19]), hardware will not set this flag.
* |[22] |RXOVERR |Receiver over Retry Error
* | | |This bit is used for receiver retry counts over than retry number limitation.
* | | |0 = Receiver retries counts is less than RXRTY (SCn_CTL[18:16]) + 1.
* | | |1 = Receiver retries counts is equal or over than RXRTY (SCn_CTL[18:16]) + 1.
* | | |Note1: This bit can be cleared by writing 1 to it.
* | | |Note2: If CPU enables receiver retries function by setting RXRTYEN (SCn_CTL[19]), hardware will not set this flag.
* |[23] |RXACT |Receiver in Active Status Flag (Read Only)
* | | |This bit indicates Rx transfer status.
* | | |0 = This bit is cleared automatically when Rx transfer is finished.
* | | |1 = This bit is set by hardware when Rx transfer is in active.
* |[26:24] |TXPOINT |Transmit Buffer Pointer Status (Read Only)
* | | |This field indicates the Tx buffer pointer status
* | | |When CPU writes data into SCn_DAT, TXPOINT increases one
* | | |When one byte of Tx buffer is transferred to transmitter shift register, TXPOINT decreases one.
* |[29] |TXRERR |Transmitter Retry Error
* | | |This bit is used for indicate transmitter error retry and set by hardware..
* | | |0 = No Tx retry transfer.
* | | |1 = Tx has any error and retries transfer.
* | | |Note1: This bit can be cleared by writing 1 to it.
* | | |Note2: This bit is a flag and cannot generate any interrupt to CPU.
* |[30] |TXOVERR |Transmitter over Retry Error
* | | |This bit is used for transmitter retry counts over than retry number limitation.
* | | |0 = Transmitter retries counts is less than TXRTY (SCn_CTL[22:20]) + 1.
* | | |1 = Transmitter retries counts is equal or over to TXRTY (SCn_CTL[22:20]) + 1.
* | | |Note: This bit can be cleared by writing 1 to it.
* |[31] |TXACT |Transmit in Active Status Flag (Read Only)
* | | |This bit indicates Tx transmit status.
* | | |0 = This bit is cleared automatically when Tx transfer is finished or the last byte transmission has completed.
* | | |1 = Transmit is active and this bit is set by hardware when Tx transfer is in active and the STOP bit of the last byte has not been transmitted.
* @var SC_T::PINCTL
* Offset: 0x24 SC Pin Control State Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[0] |PWREN |SCn_PWR Pin Signal
* | | |User can set PWRINV (SCn_PINCTL[11]) and PWREN (SCn_PINCTL[0]) to decide SCn_PWR pin is in high or low level.
* | | |Write this field to drive SCn_PWR pin
* | | |Refer PWRINV (SCn_PINCTL[11]) description for programming SCn_PWR pin voltage level.
* | | |Read this field to get SCn_PWR signal status.
* | | |0 = SCn_PWR signal status is low.
* | | |1 = SCn_PWR signal status is high.
* | | |Note: When operating at activation, warm reset or deactivation mode, this bit will be changed automatically
* | | |Thus, do not fill in this field when operating in these modes.
* |[1] |RSTEN |SCn_RST Pin Signal
* | | |User can set RSTEN (SCn_PINCTL[1]) to decide SCn_RST pin is in high or low level.
* | | |Write this field to drive SCn_RST pin.
* | | |0 = Drive SCn_RST pin to low.
* | | |1 = Drive SCn_RST pin to high.
* | | |Read this field to get SCn_RST signal status.
* | | |0 = SCn_RST signal status is low.
* | | |1 = SCn_RST signal status is high.
* | | |Note: When operating at activation, warm reset or deactivation mode, this bit will be changed automatically
* | | |Thus, do not fill in this field when operating in these modes.
* |[6] |CLKKEEP |SC Clock Enable Bit
* | | |0 = SC clock generation Disabled.
* | | |1 = SC clock always keeps free running.
* | | |Note: When operating in activation, warm reset or deactivation mode, this bit will be changed automatically
* | | |Thus, do not fill in this field when operating in these modes.
* |[9] |SCDATA |SCn_DATA Pin Signal
* | | |This bit is the signal status of SCn_DATA but user can drive SCn_DATA pin to high or low by setting this bit.
* | | |0 = Drive SCn_DATA pin to low.
* | | |1 = Drive SCn_DATA pin to high.
* | | |Read this field to get SCn_DATA signal status.
* | | |0 = SCn_DATA signal status is low.
* | | |1 = SCn_DATA signal status is high.
* | | |Note: When SC is at activation, warm reset or deactivation mode, this bit will be changed automatically
* | | |Thus, do not fill in this field when SC is in these modes.
* |[11] |PWRINV |SCn_PWR Pin Inverse
* | | |This bit is used for inverse the SCn_PWR pin.
* | | |There are four kinds of combination for SCn_PWR pin setting by PWRINV (SCn_PINCTL[11]) and PWREN (SCn_PINCTL[0]).
* | | |PWRINV (SCn_PINCTL[11]) is bit 1 and PWREN (SCn_PINCTL[0]) is bit 0 and all conditions as below list,
* | | |00 = SCn_PWR pin is 0.
* | | |01 = SCn_PWR pin is 1.
* | | |10 = SCn_PWR pin is 1.
* | | |11 = SCn_PWR pin is 0.
* | | |Note: User must select PWRINV (SCn_PINCTL[11]) before smart card is enabled by SCEN (SCn_CTL[0]).
* |[16] |DATASTS |SCn_DATA Pin Status (Read Only)
* | | |This bit is the pin status of SCn_DATA.
* | | |0 = The SCn_DATA pin status is low.
* | | |1 = The SCn_DATA pin status is high.
* |[17] |PWRSTS |SCn_PWR Pin Status (Read Only)
* | | |This bit is the pin status of SCn_PWR.
* | | |0 = SCn_PWR pin to low.
* | | |1 = SCn_PWR pin to high.
* |[18] |RSTSTS |SCn_RST Pin Status (Read Only)
* | | |This bit is the pin status of SCn_RST.
* | | |0 = SCn_RST pin is low.
* | | |1 = SCn_RST pin is high.
* |[30] |SYNC |SYNC Flag Indicator (Read Only)
* | | |Due to synchronization, user should check this bit when writing a new value to SCn_PINCTL register.
* | | |0 = Synchronizing is completion, user can write new data to SCn_PINCTL register.
* | | |1 = Last value is synchronizing.
* @var SC_T::TMRCTL0
* Offset: 0x28 SC Internal Timer0 Control Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[23:0] |CNT |Timer0 Counter Value
* | | |This field indicates the internal Timer0 counter values.
* | | |Note: Unit of Timer0 counter is ETU base.
* |[27:24] |OPMODE |Timer0 Operation Mode Selection
* | | |This field indicates the internal 24-bit Timer0 operation selection.
* | | |Refer to Table 7.14-3 for programming Timer0.
* |[31] |SYNC |SYNC Flag Indicator (Read Only)
* | | |Due to synchronization, user should check this bit when writing a new value to the SCn_TMRCTL0 register.
* | | |0 = Synchronizing is completion, user can write new data to SCn_TMRCTL0 register.
* | | |1 = Last value is synchronizing.
* @var SC_T::TMRCTL1
* Offset: 0x2C SC Internal Timer1 Control Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |CNT |Timer 1 Counter Value
* | | |This field indicates the internal Timer1 counter values.
* | | |Note: Unit of Timer1 counter is ETU base.
* |[27:24] |OPMODE |Timer 1 Operation Mode Selection
* | | |This field indicates the internal 8-bit Timer1 operation selection.
* | | |Refer to Table 7.14-3 for programming Timer1.
* |[31] |SYNC |SYNC Flag Indicator (Read Only)
* | | |Due to synchronization, software should check this bit when writing a new value to SCn_TMRCTL1 register.
* | | |0 = Synchronizing is completion, user can write new data to SCn_TMRCTL1 register.
* | | |1 = Last value is synchronizing.
* @var SC_T::TMRCTL2
* Offset: 0x30 SC Internal Timer2 Control Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[7:0] |CNT |Timer 2 Counter Value
* | | |This field indicates the internal Timer2 counter values.
* | | |Note: Unit of Timer2 counter is ETU base.
* |[27:24] |OPMODE |Timer 2 Operation Mode Selection
* | | |This field indicates the internal 8-bit Timer2 operation selection
* | | |Refer to Table 7.14-3 for programming Timer2.
* |[31] |SYNC |SYNC Flag Indicator (Read Only)
* | | |Due to synchronization, user should check this bit when writing a new value to SCn_TMRCTL2 register.
* | | |0 = Synchronizing is completion, user can write new data to SCn_TMRCTL2 register.
* | | |1 = Last value is synchronizing.
* @var SC_T::UARTCTL
* Offset: 0x34 SC UART Mode Control Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[0] |UARTEN |UART Mode Enable Bit
* | | |Sets this bit to enable UART mode function.
* | | |0 = Smart Card mode.
* | | |1 = UART mode.
* | | |Note1: When operating in UART mode, user must set CONSEL (SCn_CTL[5:4]) = 00 and AUTOCEN (SCn_CTL[3]) = 0.
* | | |Note2: When operating in Smart Card mode, user must set UARTEN (SCn_UARTCTL[0]) = 0.
* | | |Note3: When UART mode is enabled, hardware will generate a reset to reset FIFO and internal state machine.
* |[5:4] |WLS |Word Length Selection
* | | |This field is used for select UART data length.
* | | |00 = Word length is 8 bits.
* | | |01 = Word length is 7 bits.
* | | |10 = Word length is 6 bits.
* | | |11 = Word length is 5 bits.
* | | |Note: In smart card mode, this WLS must be 00.
* |[6] |PBOFF |Parity Bit Disable Bit
* | | |Sets this bit is used for disable parity check function.
* | | |0 = Parity bit is generated or checked between the "last data word bit" and "stop bit" of the serial data.
* | | |1 = Parity bit is not generated (transmitting data) or checked (receiving data) during transfer.
* | | |Note: In smart card mode, this field must be 0 (default setting is with parity bit).
* |[7] |OPE |Odd Parity Enable Bit
* | | |This is used for odd/even parity selection.
* | | |0 = Even number of logic 1 are transmitted or check the data word and parity bits in receiving mode.
* | | |1 = Odd number of logic 1 are transmitted or check the data word and parity bits in receiving mode.
* | | |Note: This bit has effect only when PBOFF bit is 0.
* @var SC_T::ACTCTL
* Offset: 0x4C SC Activation Control Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[4:0] |T1EXT |T1 Extend Time of Hardware Activation
* | | |This field provide the configurable cycles to extend the activation time T1 period.
* | | |The cycle scaling factor is 2048.
* | | |Extend cycles = (filled value * 2048) cycles.
* | | |Refer to SC activation sequence in Figure 7.14-4.
* | | |For example,
* | | |SCLK = 4MHz, each cycle = 0.25us,.
* | | |Filled 20 to this field
* | | |Extend time = 20 * 2048 * 0.25us = 10.24 ms.
* | | |Note: Setting 0 to this field conforms to the protocol ISO/IEC 7816-3
*/
__IO uint32_t DAT; /*!< [0x0000] SC Receive/Transmit Holding Buffer Register */
__IO uint32_t CTL; /*!< [0x0004] SC Control Register */
__IO uint32_t ALTCTL; /*!< [0x0008] SC Alternate Control Register */
__IO uint32_t EGT; /*!< [0x000c] SC Extra Guard Time Register */
__IO uint32_t RXTOUT; /*!< [0x0010] SC Receive Buffer Time-out Counter Register */
__IO uint32_t ETUCTL; /*!< [0x0014] SC Element Time Unit Control Register */
__IO uint32_t INTEN; /*!< [0x0018] SC Interrupt Enable Control Register */
__IO uint32_t INTSTS; /*!< [0x001c] SC Interrupt Status Register */
__IO uint32_t STATUS; /*!< [0x0020] SC Transfer Status Register */
__IO uint32_t PINCTL; /*!< [0x0024] SC Pin Control State Register */
__IO uint32_t TMRCTL0; /*!< [0x0028] SC Internal Timer0 Control Register */
__IO uint32_t TMRCTL1; /*!< [0x002c] SC Internal Timer1 Control Register */
__IO uint32_t TMRCTL2; /*!< [0x0030] SC Internal Timer2 Control Register */
__IO uint32_t UARTCTL; /*!< [0x0034] SC UART Mode Control Register */
/// @cond HIDDEN_SYMBOLS
__I uint32_t RESERVE0[5];
/// @endcond //HIDDEN_SYMBOLS
__IO uint32_t ACTCTL; /*!< [0x004c] SC Activation Control Register */
} SC_T;
/**
@addtogroup SC_CONST SC Bit Field Definition
Constant Definitions for SC Controller
@{ */
#define SC_DAT_DAT_Pos (0) /*!< SC_T::DAT: DAT Position */
#define SC_DAT_DAT_Msk (0xfful << SC_DAT_DAT_Pos) /*!< SC_T::DAT: DAT Mask */
#define SC_CTL_SCEN_Pos (0) /*!< SC_T::CTL: SCEN Position */
#define SC_CTL_SCEN_Msk (0x1ul << SC_CTL_SCEN_Pos) /*!< SC_T::CTL: SCEN Mask */
#define SC_CTL_RXOFF_Pos (1) /*!< SC_T::CTL: RXOFF Position */
#define SC_CTL_RXOFF_Msk (0x1ul << SC_CTL_RXOFF_Pos) /*!< SC_T::CTL: RXOFF Mask */
#define SC_CTL_TXOFF_Pos (2) /*!< SC_T::CTL: TXOFF Position */
#define SC_CTL_TXOFF_Msk (0x1ul << SC_CTL_TXOFF_Pos) /*!< SC_T::CTL: TXOFF Mask */
#define SC_CTL_AUTOCEN_Pos (3) /*!< SC_T::CTL: AUTOCEN Position */
#define SC_CTL_AUTOCEN_Msk (0x1ul << SC_CTL_AUTOCEN_Pos) /*!< SC_T::CTL: AUTOCEN Mask */
#define SC_CTL_CONSEL_Pos (4) /*!< SC_T::CTL: CONSEL Position */
#define SC_CTL_CONSEL_Msk (0x3ul << SC_CTL_CONSEL_Pos) /*!< SC_T::CTL: CONSEL Mask */
#define SC_CTL_RXTRGLV_Pos (6) /*!< SC_T::CTL: RXTRGLV Position */
#define SC_CTL_RXTRGLV_Msk (0x3ul << SC_CTL_RXTRGLV_Pos) /*!< SC_T::CTL: RXTRGLV Mask */
#define SC_CTL_BGT_Pos (8) /*!< SC_T::CTL: BGT Position */
#define SC_CTL_BGT_Msk (0x1ful << SC_CTL_BGT_Pos) /*!< SC_T::CTL: BGT Mask */
#define SC_CTL_TMRSEL_Pos (13) /*!< SC_T::CTL: TMRSEL Position */
#define SC_CTL_TMRSEL_Msk (0x3ul << SC_CTL_TMRSEL_Pos) /*!< SC_T::CTL: TMRSEL Mask */
#define SC_CTL_NSB_Pos (15) /*!< SC_T::CTL: NSB Position */
#define SC_CTL_NSB_Msk (0x1ul << SC_CTL_NSB_Pos) /*!< SC_T::CTL: NSB Mask */
#define SC_CTL_RXRTY_Pos (16) /*!< SC_T::CTL: RXRTY Position */
#define SC_CTL_RXRTY_Msk (0x7ul << SC_CTL_RXRTY_Pos) /*!< SC_T::CTL: RXRTY Mask */
#define SC_CTL_RXRTYEN_Pos (19) /*!< SC_T::CTL: RXRTYEN Position */
#define SC_CTL_RXRTYEN_Msk (0x1ul << SC_CTL_RXRTYEN_Pos) /*!< SC_T::CTL: RXRTYEN Mask */
#define SC_CTL_TXRTY_Pos (20) /*!< SC_T::CTL: TXRTY Position */
#define SC_CTL_TXRTY_Msk (0x7ul << SC_CTL_TXRTY_Pos) /*!< SC_T::CTL: TXRTY Mask */
#define SC_CTL_TXRTYEN_Pos (23) /*!< SC_T::CTL: TXRTYEN Position */
#define SC_CTL_TXRTYEN_Msk (0x1ul << SC_CTL_TXRTYEN_Pos) /*!< SC_T::CTL: TXRTYEN Mask */
#define SC_CTL_CDDBSEL_Pos (24) /*!< SC_T::CTL: CDDBSEL Position */
#define SC_CTL_CDDBSEL_Msk (0x3ul << SC_CTL_CDDBSEL_Pos) /*!< SC_T::CTL: CDDBSEL Mask */
#define SC_CTL_CDLV_Pos (26) /*!< SC_T::CTL: CDLV Position */
#define SC_CTL_CDLV_Msk (0x1ul << SC_CTL_CDLV_Pos) /*!< SC_T::CTL: CDLV Mask */
#define SC_CTL_SYNC_Pos (30) /*!< SC_T::CTL: SYNC Position */
#define SC_CTL_SYNC_Msk (0x1ul << SC_CTL_SYNC_Pos) /*!< SC_T::CTL: SYNC Mask */
#define SC_ALTCTL_TXRST_Pos (0) /*!< SC_T::ALTCTL: TXRST Position */
#define SC_ALTCTL_TXRST_Msk (0x1ul << SC_ALTCTL_TXRST_Pos) /*!< SC_T::ALTCTL: TXRST Mask */
#define SC_ALTCTL_RXRST_Pos (1) /*!< SC_T::ALTCTL: RXRST Position */
#define SC_ALTCTL_RXRST_Msk (0x1ul << SC_ALTCTL_RXRST_Pos) /*!< SC_T::ALTCTL: RXRST Mask */
#define SC_ALTCTL_DACTEN_Pos (2) /*!< SC_T::ALTCTL: DACTEN Position */
#define SC_ALTCTL_DACTEN_Msk (0x1ul << SC_ALTCTL_DACTEN_Pos) /*!< SC_T::ALTCTL: DACTEN Mask */
#define SC_ALTCTL_ACTEN_Pos (3) /*!< SC_T::ALTCTL: ACTEN Position */
#define SC_ALTCTL_ACTEN_Msk (0x1ul << SC_ALTCTL_ACTEN_Pos) /*!< SC_T::ALTCTL: ACTEN Mask */
#define SC_ALTCTL_WARSTEN_Pos (4) /*!< SC_T::ALTCTL: WARSTEN Position */
#define SC_ALTCTL_WARSTEN_Msk (0x1ul << SC_ALTCTL_WARSTEN_Pos) /*!< SC_T::ALTCTL: WARSTEN Mask */
#define SC_ALTCTL_CNTEN0_Pos (5) /*!< SC_T::ALTCTL: CNTEN0 Position */
#define SC_ALTCTL_CNTEN0_Msk (0x1ul << SC_ALTCTL_CNTEN0_Pos) /*!< SC_T::ALTCTL: CNTEN0 Mask */
#define SC_ALTCTL_CNTEN1_Pos (6) /*!< SC_T::ALTCTL: CNTEN1 Position */
#define SC_ALTCTL_CNTEN1_Msk (0x1ul << SC_ALTCTL_CNTEN1_Pos) /*!< SC_T::ALTCTL: CNTEN1 Mask */
#define SC_ALTCTL_CNTEN2_Pos (7) /*!< SC_T::ALTCTL: CNTEN2 Position */
#define SC_ALTCTL_CNTEN2_Msk (0x1ul << SC_ALTCTL_CNTEN2_Pos) /*!< SC_T::ALTCTL: CNTEN2 Mask */
#define SC_ALTCTL_INITSEL_Pos (8) /*!< SC_T::ALTCTL: INITSEL Position */
#define SC_ALTCTL_INITSEL_Msk (0x3ul << SC_ALTCTL_INITSEL_Pos) /*!< SC_T::ALTCTL: INITSEL Mask */
#define SC_ALTCTL_ADACEN_Pos (11) /*!< SC_T::ALTCTL: ADACEN Position */
#define SC_ALTCTL_ADACEN_Msk (0x1ul << SC_ALTCTL_ADACEN_Pos) /*!< SC_T::ALTCTL: ADACEN Mask */
#define SC_ALTCTL_RXBGTEN_Pos (12) /*!< SC_T::ALTCTL: RXBGTEN Position */
#define SC_ALTCTL_RXBGTEN_Msk (0x1ul << SC_ALTCTL_RXBGTEN_Pos) /*!< SC_T::ALTCTL: RXBGTEN Mask */
#define SC_ALTCTL_ACTSTS0_Pos (13) /*!< SC_T::ALTCTL: ACTSTS0 Position */
#define SC_ALTCTL_ACTSTS0_Msk (0x1ul << SC_ALTCTL_ACTSTS0_Pos) /*!< SC_T::ALTCTL: ACTSTS0 Mask */
#define SC_ALTCTL_ACTSTS1_Pos (14) /*!< SC_T::ALTCTL: ACTSTS1 Position */
#define SC_ALTCTL_ACTSTS1_Msk (0x1ul << SC_ALTCTL_ACTSTS1_Pos) /*!< SC_T::ALTCTL: ACTSTS1 Mask */
#define SC_ALTCTL_ACTSTS2_Pos (15) /*!< SC_T::ALTCTL: ACTSTS2 Position */
#define SC_ALTCTL_ACTSTS2_Msk (0x1ul << SC_ALTCTL_ACTSTS2_Pos) /*!< SC_T::ALTCTL: ACTSTS2 Mask */
#define SC_ALTCTL_SYNC_Pos (31) /*!< SC_T::ALTCTL: SYNC Position */
#define SC_ALTCTL_SYNC_Msk (0x1ul << SC_ALTCTL_SYNC_Pos) /*!< SC_T::ALTCTL: SYNC Mask */
#define SC_EGT_EGT_Pos (0) /*!< SC_T::EGT: EGT Position */
#define SC_EGT_EGT_Msk (0xfful << SC_EGT_EGT_Pos) /*!< SC_T::EGT: EGT Mask */
#define SC_RXTOUT_RFTM_Pos (0) /*!< SC_T::RXTOUT: RFTM Position */
#define SC_RXTOUT_RFTM_Msk (0x1fful << SC_RXTOUT_RFTM_Pos) /*!< SC_T::RXTOUT: RFTM Mask */
#define SC_ETUCTL_ETURDIV_Pos (0) /*!< SC_T::ETUCTL: ETURDIV Position */
#define SC_ETUCTL_ETURDIV_Msk (0xffful << SC_ETUCTL_ETURDIV_Pos) /*!< SC_T::ETUCTL: ETURDIV Mask */
#define SC_INTEN_RDAIEN_Pos (0) /*!< SC_T::INTEN: RDAIEN Position */
#define SC_INTEN_RDAIEN_Msk (0x1ul << SC_INTEN_RDAIEN_Pos) /*!< SC_T::INTEN: RDAIEN Mask */
#define SC_INTEN_TBEIEN_Pos (1) /*!< SC_T::INTEN: TBEIEN Position */
#define SC_INTEN_TBEIEN_Msk (0x1ul << SC_INTEN_TBEIEN_Pos) /*!< SC_T::INTEN: TBEIEN Mask */
#define SC_INTEN_TERRIEN_Pos (2) /*!< SC_T::INTEN: TERRIEN Position */
#define SC_INTEN_TERRIEN_Msk (0x1ul << SC_INTEN_TERRIEN_Pos) /*!< SC_T::INTEN: TERRIEN Mask */
#define SC_INTEN_TMR0IEN_Pos (3) /*!< SC_T::INTEN: TMR0IEN Position */
#define SC_INTEN_TMR0IEN_Msk (0x1ul << SC_INTEN_TMR0IEN_Pos) /*!< SC_T::INTEN: TMR0IEN Mask */
#define SC_INTEN_TMR1IEN_Pos (4) /*!< SC_T::INTEN: TMR1IEN Position */
#define SC_INTEN_TMR1IEN_Msk (0x1ul << SC_INTEN_TMR1IEN_Pos) /*!< SC_T::INTEN: TMR1IEN Mask */
#define SC_INTEN_TMR2IEN_Pos (5) /*!< SC_T::INTEN: TMR2IEN Position */
#define SC_INTEN_TMR2IEN_Msk (0x1ul << SC_INTEN_TMR2IEN_Pos) /*!< SC_T::INTEN: TMR2IEN Mask */
#define SC_INTEN_BGTIEN_Pos (6) /*!< SC_T::INTEN: BGTIEN Position */
#define SC_INTEN_BGTIEN_Msk (0x1ul << SC_INTEN_BGTIEN_Pos) /*!< SC_T::INTEN: BGTIEN Mask */
#define SC_INTEN_CDIEN_Pos (7) /*!< SC_T::INTEN: CDIEN Position */
#define SC_INTEN_CDIEN_Msk (0x1ul << SC_INTEN_CDIEN_Pos) /*!< SC_T::INTEN: CDIEN Mask */
#define SC_INTEN_INITIEN_Pos (8) /*!< SC_T::INTEN: INITIEN Position */
#define SC_INTEN_INITIEN_Msk (0x1ul << SC_INTEN_INITIEN_Pos) /*!< SC_T::INTEN: INITIEN Mask */
#define SC_INTEN_RXTOIEN_Pos (9) /*!< SC_T::INTEN: RXTOIEN Position */
#define SC_INTEN_RXTOIEN_Msk (0x1ul << SC_INTEN_RXTOIEN_Pos) /*!< SC_T::INTEN: RXTOIEN Mask */
#define SC_INTEN_ACERRIEN_Pos (10) /*!< SC_T::INTEN: ACERRIEN Position */
#define SC_INTEN_ACERRIEN_Msk (0x1ul << SC_INTEN_ACERRIEN_Pos) /*!< SC_T::INTEN: ACERRIEN Mask */
#define SC_INTSTS_RDAIF_Pos (0) /*!< SC_T::INTSTS: RDAIF Position */
#define SC_INTSTS_RDAIF_Msk (0x1ul << SC_INTSTS_RDAIF_Pos) /*!< SC_T::INTSTS: RDAIF Mask */
#define SC_INTSTS_TBEIF_Pos (1) /*!< SC_T::INTSTS: TBEIF Position */
#define SC_INTSTS_TBEIF_Msk (0x1ul << SC_INTSTS_TBEIF_Pos) /*!< SC_T::INTSTS: TBEIF Mask */
#define SC_INTSTS_TERRIF_Pos (2) /*!< SC_T::INTSTS: TERRIF Position */
#define SC_INTSTS_TERRIF_Msk (0x1ul << SC_INTSTS_TERRIF_Pos) /*!< SC_T::INTSTS: TERRIF Mask */
#define SC_INTSTS_TMR0IF_Pos (3) /*!< SC_T::INTSTS: TMR0IF Position */
#define SC_INTSTS_TMR0IF_Msk (0x1ul << SC_INTSTS_TMR0IF_Pos) /*!< SC_T::INTSTS: TMR0IF Mask */
#define SC_INTSTS_TMR1IF_Pos (4) /*!< SC_T::INTSTS: TMR1IF Position */
#define SC_INTSTS_TMR1IF_Msk (0x1ul << SC_INTSTS_TMR1IF_Pos) /*!< SC_T::INTSTS: TMR1IF Mask */
#define SC_INTSTS_TMR2IF_Pos (5) /*!< SC_T::INTSTS: TMR2IF Position */
#define SC_INTSTS_TMR2IF_Msk (0x1ul << SC_INTSTS_TMR2IF_Pos) /*!< SC_T::INTSTS: TMR2IF Mask */
#define SC_INTSTS_BGTIF_Pos (6) /*!< SC_T::INTSTS: BGTIF Position */
#define SC_INTSTS_BGTIF_Msk (0x1ul << SC_INTSTS_BGTIF_Pos) /*!< SC_T::INTSTS: BGTIF Mask */
#define SC_INTSTS_CDIF_Pos (7) /*!< SC_T::INTSTS: CDIF Position */
#define SC_INTSTS_CDIF_Msk (0x1ul << SC_INTSTS_CDIF_Pos) /*!< SC_T::INTSTS: CDIF Mask */
#define SC_INTSTS_INITIF_Pos (8) /*!< SC_T::INTSTS: INITIF Position */
#define SC_INTSTS_INITIF_Msk (0x1ul << SC_INTSTS_INITIF_Pos) /*!< SC_T::INTSTS: INITIF Mask */
#define SC_INTSTS_RXTOIF_Pos (9) /*!< SC_T::INTSTS: RXTOIF Position */
#define SC_INTSTS_RXTOIF_Msk (0x1ul << SC_INTSTS_RXTOIF_Pos) /*!< SC_T::INTSTS: RXTOIF Mask */
#define SC_INTSTS_ACERRIF_Pos (10) /*!< SC_T::INTSTS: ACERRIF Position */
#define SC_INTSTS_ACERRIF_Msk (0x1ul << SC_INTSTS_ACERRIF_Pos) /*!< SC_T::INTSTS: ACERRIF Mask */
#define SC_STATUS_RXOV_Pos (0) /*!< SC_T::STATUS: RXOV Position */
#define SC_STATUS_RXOV_Msk (0x1ul << SC_STATUS_RXOV_Pos) /*!< SC_T::STATUS: RXOV Mask */
#define SC_STATUS_RXEMPTY_Pos (1) /*!< SC_T::STATUS: RXEMPTY Position */
#define SC_STATUS_RXEMPTY_Msk (0x1ul << SC_STATUS_RXEMPTY_Pos) /*!< SC_T::STATUS: RXEMPTY Mask */
#define SC_STATUS_RXFULL_Pos (2) /*!< SC_T::STATUS: RXFULL Position */
#define SC_STATUS_RXFULL_Msk (0x1ul << SC_STATUS_RXFULL_Pos) /*!< SC_T::STATUS: RXFULL Mask */
#define SC_STATUS_PEF_Pos (4) /*!< SC_T::STATUS: PEF Position */
#define SC_STATUS_PEF_Msk (0x1ul << SC_STATUS_PEF_Pos) /*!< SC_T::STATUS: PEF Mask */
#define SC_STATUS_FEF_Pos (5) /*!< SC_T::STATUS: FEF Position */
#define SC_STATUS_FEF_Msk (0x1ul << SC_STATUS_FEF_Pos) /*!< SC_T::STATUS: FEF Mask */
#define SC_STATUS_BEF_Pos (6) /*!< SC_T::STATUS: BEF Position */
#define SC_STATUS_BEF_Msk (0x1ul << SC_STATUS_BEF_Pos) /*!< SC_T::STATUS: BEF Mask */
#define SC_STATUS_TXOV_Pos (8) /*!< SC_T::STATUS: TXOV Position */
#define SC_STATUS_TXOV_Msk (0x1ul << SC_STATUS_TXOV_Pos) /*!< SC_T::STATUS: TXOV Mask */
#define SC_STATUS_TXEMPTY_Pos (9) /*!< SC_T::STATUS: TXEMPTY Position */
#define SC_STATUS_TXEMPTY_Msk (0x1ul << SC_STATUS_TXEMPTY_Pos) /*!< SC_T::STATUS: TXEMPTY Mask */
#define SC_STATUS_TXFULL_Pos (10) /*!< SC_T::STATUS: TXFULL Position */
#define SC_STATUS_TXFULL_Msk (0x1ul << SC_STATUS_TXFULL_Pos) /*!< SC_T::STATUS: TXFULL Mask */
#define SC_STATUS_CREMOVE_Pos (11) /*!< SC_T::STATUS: CREMOVE Position */
#define SC_STATUS_CREMOVE_Msk (0x1ul << SC_STATUS_CREMOVE_Pos) /*!< SC_T::STATUS: CREMOVE Mask */
#define SC_STATUS_CINSERT_Pos (12) /*!< SC_T::STATUS: CINSERT Position */
#define SC_STATUS_CINSERT_Msk (0x1ul << SC_STATUS_CINSERT_Pos) /*!< SC_T::STATUS: CINSERT Mask */
#define SC_STATUS_CDPINSTS_Pos (13) /*!< SC_T::STATUS: CDPINSTS Position */
#define SC_STATUS_CDPINSTS_Msk (0x1ul << SC_STATUS_CDPINSTS_Pos) /*!< SC_T::STATUS: CDPINSTS Mask */
#define SC_STATUS_RXPOINT_Pos (16) /*!< SC_T::STATUS: RXPOINT Position */
#define SC_STATUS_RXPOINT_Msk (0x7ul << SC_STATUS_RXPOINT_Pos) /*!< SC_T::STATUS: RXPOINT Mask */
#define SC_STATUS_RXRERR_Pos (21) /*!< SC_T::STATUS: RXRERR Position */
#define SC_STATUS_RXRERR_Msk (0x1ul << SC_STATUS_RXRERR_Pos) /*!< SC_T::STATUS: RXRERR Mask */
#define SC_STATUS_RXOVERR_Pos (22) /*!< SC_T::STATUS: RXOVERR Position */
#define SC_STATUS_RXOVERR_Msk (0x1ul << SC_STATUS_RXOVERR_Pos) /*!< SC_T::STATUS: RXOVERR Mask */
#define SC_STATUS_RXACT_Pos (23) /*!< SC_T::STATUS: RXACT Position */
#define SC_STATUS_RXACT_Msk (0x1ul << SC_STATUS_RXACT_Pos) /*!< SC_T::STATUS: RXACT Mask */
#define SC_STATUS_TXPOINT_Pos (24) /*!< SC_T::STATUS: TXPOINT Position */
#define SC_STATUS_TXPOINT_Msk (0x7ul << SC_STATUS_TXPOINT_Pos) /*!< SC_T::STATUS: TXPOINT Mask */
#define SC_STATUS_TXRERR_Pos (29) /*!< SC_T::STATUS: TXRERR Position */
#define SC_STATUS_TXRERR_Msk (0x1ul << SC_STATUS_TXRERR_Pos) /*!< SC_T::STATUS: TXRERR Mask */
#define SC_STATUS_TXOVERR_Pos (30) /*!< SC_T::STATUS: TXOVERR Position */
#define SC_STATUS_TXOVERR_Msk (0x1ul << SC_STATUS_TXOVERR_Pos) /*!< SC_T::STATUS: TXOVERR Mask */
#define SC_STATUS_TXACT_Pos (31) /*!< SC_T::STATUS: TXACT Position */
#define SC_STATUS_TXACT_Msk (0x1ul << SC_STATUS_TXACT_Pos) /*!< SC_T::STATUS: TXACT Mask */
#define SC_PINCTL_PWREN_Pos (0) /*!< SC_T::PINCTL: PWREN Position */
#define SC_PINCTL_PWREN_Msk (0x1ul << SC_PINCTL_PWREN_Pos) /*!< SC_T::PINCTL: PWREN Mask */
#define SC_PINCTL_RSTEN_Pos (1) /*!< SC_T::PINCTL: RSTEN Position */
#define SC_PINCTL_RSTEN_Msk (0x1ul << SC_PINCTL_RSTEN_Pos) /*!< SC_T::PINCTL: RSTEN Mask */
#define SC_PINCTL_CLKKEEP_Pos (6) /*!< SC_T::PINCTL: CLKKEEP Position */
#define SC_PINCTL_CLKKEEP_Msk (0x1ul << SC_PINCTL_CLKKEEP_Pos) /*!< SC_T::PINCTL: CLKKEEP Mask */
#define SC_PINCTL_SCDATA_Pos (9) /*!< SC_T::PINCTL: SCDATA Position */
#define SC_PINCTL_SCDATA_Msk (0x1ul << SC_PINCTL_SCDATA_Pos) /*!< SC_T::PINCTL: SCDATA Mask */
#define SC_PINCTL_PWRINV_Pos (11) /*!< SC_T::PINCTL: PWRINV Position */
#define SC_PINCTL_PWRINV_Msk (0x1ul << SC_PINCTL_PWRINV_Pos) /*!< SC_T::PINCTL: PWRINV Mask */
#define SC_PINCTL_DATASTS_Pos (16) /*!< SC_T::PINCTL: DATASTS Position */
#define SC_PINCTL_DATASTS_Msk (0x1ul << SC_PINCTL_DATASTS_Pos) /*!< SC_T::PINCTL: DATASTS Mask */
#define SC_PINCTL_PWRSTS_Pos (17) /*!< SC_T::PINCTL: PWRSTS Position */
#define SC_PINCTL_PWRSTS_Msk (0x1ul << SC_PINCTL_PWRSTS_Pos) /*!< SC_T::PINCTL: PWRSTS Mask */
#define SC_PINCTL_RSTSTS_Pos (18) /*!< SC_T::PINCTL: RSTSTS Position */
#define SC_PINCTL_RSTSTS_Msk (0x1ul << SC_PINCTL_RSTSTS_Pos) /*!< SC_T::PINCTL: RSTSTS Mask */
#define SC_PINCTL_SYNC_Pos (30) /*!< SC_T::PINCTL: SYNC Position */
#define SC_PINCTL_SYNC_Msk (0x1ul << SC_PINCTL_SYNC_Pos) /*!< SC_T::PINCTL: SYNC Mask */
#define SC_TMRCTL0_CNT_Pos (0) /*!< SC_T::TMRCTL0: CNT Position */
#define SC_TMRCTL0_CNT_Msk (0xfffffful << SC_TMRCTL0_CNT_Pos) /*!< SC_T::TMRCTL0: CNT Mask */
#define SC_TMRCTL0_OPMODE_Pos (24) /*!< SC_T::TMRCTL0: OPMODE Position */
#define SC_TMRCTL0_OPMODE_Msk (0xful << SC_TMRCTL0_OPMODE_Pos) /*!< SC_T::TMRCTL0: OPMODE Mask */
#define SC_TMRCTL0_SYNC_Pos (31) /*!< SC_T::TMRCTL0: SYNC Position */
#define SC_TMRCTL0_SYNC_Msk (0x1ul << SC_TMRCTL0_SYNC_Pos) /*!< SC_T::TMRCTL0: SYNC Mask */
#define SC_TMRCTL1_CNT_Pos (0) /*!< SC_T::TMRCTL1: CNT Position */
#define SC_TMRCTL1_CNT_Msk (0xfful << SC_TMRCTL1_CNT_Pos) /*!< SC_T::TMRCTL1: CNT Mask */
#define SC_TMRCTL1_OPMODE_Pos (24) /*!< SC_T::TMRCTL1: OPMODE Position */
#define SC_TMRCTL1_OPMODE_Msk (0xful << SC_TMRCTL1_OPMODE_Pos) /*!< SC_T::TMRCTL1: OPMODE Mask */
#define SC_TMRCTL1_SYNC_Pos (31) /*!< SC_T::TMRCTL1: SYNC Position */
#define SC_TMRCTL1_SYNC_Msk (0x1ul << SC_TMRCTL1_SYNC_Pos) /*!< SC_T::TMRCTL1: SYNC Mask */
#define SC_TMRCTL2_CNT_Pos (0) /*!< SC_T::TMRCTL2: CNT Position */
#define SC_TMRCTL2_CNT_Msk (0xfful << SC_TMRCTL2_CNT_Pos) /*!< SC_T::TMRCTL2: CNT Mask */
#define SC_TMRCTL2_OPMODE_Pos (24) /*!< SC_T::TMRCTL2: OPMODE Position */
#define SC_TMRCTL2_OPMODE_Msk (0xful << SC_TMRCTL2_OPMODE_Pos) /*!< SC_T::TMRCTL2: OPMODE Mask */
#define SC_TMRCTL2_SYNC_Pos (31) /*!< SC_T::TMRCTL2: SYNC Position */
#define SC_TMRCTL2_SYNC_Msk (0x1ul << SC_TMRCTL2_SYNC_Pos) /*!< SC_T::TMRCTL2: SYNC Mask */
#define SC_UARTCTL_UARTEN_Pos (0) /*!< SC_T::UARTCTL: UARTEN Position */
#define SC_UARTCTL_UARTEN_Msk (0x1ul << SC_UARTCTL_UARTEN_Pos) /*!< SC_T::UARTCTL: UARTEN Mask */
#define SC_UARTCTL_WLS_Pos (4) /*!< SC_T::UARTCTL: WLS Position */
#define SC_UARTCTL_WLS_Msk (0x3ul << SC_UARTCTL_WLS_Pos) /*!< SC_T::UARTCTL: WLS Mask */
#define SC_UARTCTL_PBOFF_Pos (6) /*!< SC_T::UARTCTL: PBOFF Position */
#define SC_UARTCTL_PBOFF_Msk (0x1ul << SC_UARTCTL_PBOFF_Pos) /*!< SC_T::UARTCTL: PBOFF Mask */
#define SC_UARTCTL_OPE_Pos (7) /*!< SC_T::UARTCTL: OPE Position */
#define SC_UARTCTL_OPE_Msk (0x1ul << SC_UARTCTL_OPE_Pos) /*!< SC_T::UARTCTL: OPE Mask */
#define SC_ACTCTL_T1EXT_Pos (0) /*!< SC_T::ACTCTL: T1EXT Position */
#define SC_ACTCTL_T1EXT_Msk (0x1ful << SC_ACTCTL_T1EXT_Pos) /*!< SC_T::ACTCTL: T1EXT Mask */
/** @} SC_CONST */
/** @} end of SC register group */
/** @} end of REGISTER group */
#if defined ( __CC_ARM )
#pragma no_anon_unions
#endif
#endif /* __SC_REG_H__ */
Reference in New Issue View Git Blame Copy Permalink