121 lines
4.9 KiB
C
121 lines
4.9 KiB
C
/* Name: main.c
|
|
* Project: hid-custom-rq example
|
|
* Author: Christian Starkjohann
|
|
* Creation Date: 2008-04-07
|
|
* Tabsize: 4
|
|
* Copyright: (c) 2008 by OBJECTIVE DEVELOPMENT Software GmbH
|
|
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
|
* This Revision: $Id: main.c 790 2010-05-30 21:00:26Z cs $
|
|
*/
|
|
|
|
/*
|
|
This example should run on most AVRs with only little changes. No special
|
|
hardware resources except INT0 are used. You may have to change usbconfig.h for
|
|
different I/O pins for USB. Please note that USB D+ must be the INT0 pin, or
|
|
at least be connected to INT0 as well.
|
|
We assume that an LED is connected to port B bit 0. If you connect it to a
|
|
different port or bit, change the macros below:
|
|
*/
|
|
#define LED_PORT_DDR DDRB
|
|
#define LED_PORT_OUTPUT PORTB
|
|
#define LED_BIT 0
|
|
|
|
#include <avr/io.h>
|
|
#include <avr/wdt.h>
|
|
#include <avr/interrupt.h> /* for sei() */
|
|
#include <util/delay.h> /* for _delay_ms() */
|
|
|
|
#include <avr/pgmspace.h> /* required by usbdrv.h */
|
|
#include "usbdrv.h"
|
|
#include "oddebug.h" /* This is also an example for using debug macros */
|
|
#include "requests.h" /* The custom request numbers we use */
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
/* ----------------------------- USB interface ----------------------------- */
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
PROGMEM char usbHidReportDescriptor[22] = { /* USB report descriptor */
|
|
0x06, 0x00, 0xff, // USAGE_PAGE (Generic Desktop)
|
|
0x09, 0x01, // USAGE (Vendor Usage 1)
|
|
0xa1, 0x01, // COLLECTION (Application)
|
|
0x15, 0x00, // LOGICAL_MINIMUM (0)
|
|
0x26, 0xff, 0x00, // LOGICAL_MAXIMUM (255)
|
|
0x75, 0x08, // REPORT_SIZE (8)
|
|
0x95, 0x01, // REPORT_COUNT (1)
|
|
0x09, 0x00, // USAGE (Undefined)
|
|
0xb2, 0x02, 0x01, // FEATURE (Data,Var,Abs,Buf)
|
|
0xc0 // END_COLLECTION
|
|
};
|
|
/* The descriptor above is a dummy only, it silences the drivers. The report
|
|
* it describes consists of one byte of undefined data.
|
|
* We don't transfer our data through HID reports, we use custom requests
|
|
* instead.
|
|
*/
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
usbMsgLen_t usbFunctionSetup(uchar data[8])
|
|
{
|
|
usbRequest_t *rq = (void *)data;
|
|
|
|
if((rq->bmRequestType & USBRQ_TYPE_MASK) == USBRQ_TYPE_VENDOR){
|
|
DBG1(0x50, &rq->bRequest, 1); /* debug output: print our request */
|
|
if(rq->bRequest == CUSTOM_RQ_SET_STATUS){
|
|
if(rq->wValue.bytes[0] & 1){ /* set LED */
|
|
LED_PORT_OUTPUT |= _BV(LED_BIT);
|
|
}else{ /* clear LED */
|
|
LED_PORT_OUTPUT &= ~_BV(LED_BIT);
|
|
}
|
|
}else if(rq->bRequest == CUSTOM_RQ_GET_STATUS){
|
|
static uchar dataBuffer[1]; /* buffer must stay valid when usbFunctionSetup returns */
|
|
dataBuffer[0] = ((LED_PORT_OUTPUT & _BV(LED_BIT)) != 0);
|
|
usbMsgPtr = dataBuffer; /* tell the driver which data to return */
|
|
return 1; /* tell the driver to send 1 byte */
|
|
}
|
|
}else{
|
|
/* calss requests USBRQ_HID_GET_REPORT and USBRQ_HID_SET_REPORT are
|
|
* not implemented since we never call them. The operating system
|
|
* won't call them either because our descriptor defines no meaning.
|
|
*/
|
|
}
|
|
return 0; /* default for not implemented requests: return no data back to host */
|
|
}
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
int __attribute__((noreturn)) main(void)
|
|
{
|
|
uchar i;
|
|
|
|
wdt_enable(WDTO_1S);
|
|
/* Even if you don't use the watchdog, turn it off here. On newer devices,
|
|
* the status of the watchdog (on/off, period) is PRESERVED OVER RESET!
|
|
*/
|
|
/* RESET status: all port bits are inputs without pull-up.
|
|
* That's the way we need D+ and D-. Therefore we don't need any
|
|
* additional hardware initialization.
|
|
*/
|
|
odDebugInit();
|
|
DBG1(0x00, 0, 0); /* debug output: main starts */
|
|
usbInit();
|
|
usbDeviceDisconnect(); /* enforce re-enumeration, do this while interrupts are disabled! */
|
|
i = 0;
|
|
while(--i){ /* fake USB disconnect for > 250 ms */
|
|
wdt_reset();
|
|
_delay_ms(1);
|
|
}
|
|
usbDeviceConnect();
|
|
LED_PORT_DDR |= _BV(LED_BIT); /* make the LED bit an output */
|
|
sei();
|
|
DBG1(0x01, 0, 0); /* debug output: main loop starts */
|
|
for(;;){ /* main event loop */
|
|
#if 0 /* this is a bit too aggressive for a debug output */
|
|
DBG2(0x02, 0, 0); /* debug output: main loop iterates */
|
|
#endif
|
|
wdt_reset();
|
|
usbPoll();
|
|
}
|
|
}
|
|
|
|
/* ------------------------------------------------------------------------- */
|