ProDOS-ROM-Drive/Firmware/Firmware.lst
Terence Boldt 678e68b1c4 Update driver to not need JSR $FF58 on entry
Save and restore zero page values
2022-07-12 18:32:24 -04:00

222 lines
9.1 KiB
Plaintext

ca65 V2.18 - N/A
Main file : Firmware.asm
Current file: Firmware.asm
000000r 1 ;i/o ports to write to
000000r 1 writeLatchHigh = $C081
000000r 1 writeLatchLow = $C080
000000r 1
000000r 1 ;ProDOS defines
000000r 1 command = $42 ;ProDOS command
000000r 1 unit = $43 ;7=drive 6-4=slot 3-0=not used
000000r 1 buflo = $44 ;low address of buffer
000000r 1 bufhi = $45 ;hi address of buffer
000000r 1 blklo = $46 ;low block
000000r 1 blkhi = $47 ;hi block
000000r 1 ioerr = $27 ;I/O error code
000000r 1 nodev = $28 ;no device connected
000000r 1 wperr = $2B ;write protect error
000000r 1
000000r 1 ;for relocatable code
000000r 1 ioAddressLo = $FA
000000r 1 ioAddressHi = $FB
000000r 1 tempY = $FC
000000r 1 blockHalfCounter = $FD
000000r 1 lowLatch = $FE
000000r 1 highLatch = $FF
000000r 1 knownRts = $FF58
000000r 1
000000r 1 .org $C700
00C700 1 ;code is relocatable
00C700 1 ; but set to $c700 for
00C700 1 ; readability
00C700 1
00C700 1 ;ID bytes for booting and drive detection
00C700 1 E0 20 cpx #$20 ;ID bytes for ProDOS and the
00C702 1 A0 00 ldy #$00 ; Apple Autostart ROM
00C704 1 E0 03 cpx #$03 ;
00C706 1 E0 3C cpx #$3C ;this one for older II's
00C708 1
00C708 1 ;zero out block numbers and buffer address
00C708 1 84 44 sty buflo
00C70A 1 84 46 sty blklo
00C70C 1 84 47 sty blkhi
00C70E 1 C8 iny ;set command = 1 for read block
00C70F 1 84 42 sty command
00C711 1 20 58 FF jsr knownRts ;jump to known RTS to get our address from the stack
00C714 1 BA tsx
00C715 1 BD 00 01 lda $0100,x ;this for example would be $C7 in slot 7
00C718 1 85 45 sta bufhi ;keep the slot here
00C71A 1 0A asl
00C71B 1 0A asl
00C71C 1 0A asl
00C71D 1 0A asl
00C71E 1 85 43 sta unit
00C720 1
00C720 1 ;display copyright message
00C720 1 A0 CE ldy #<text
00C722 1 drawtxt:
00C722 1 B1 44 lda (buflo),y
00C724 1 F0 06 beq boot
00C726 1 99 02 07 sta $07D0-<text,y ;put text on last line
00C729 1 C8 iny
00C72A 1 D0 F6 bne drawtxt
00C72C 1
00C72C 1 ;load block 0000 at $0800
00C72C 1 boot:
00C72C 1 A9 08 lda #$08 ;push $0800 onto the stack so an RTS will run at $0801
00C72E 1 85 45 sta bufhi
00C730 1 48 pha
00C731 1 A9 00 lda #$00
00C733 1 48 pha
00C734 1 ;This is the ProDOS entry point for this card
00C734 1 entry:
00C734 1 A6 43 ldx unit ;make sure it's drive 1
00C736 1 10 04 bpl docmd ;yep, do command
00C738 1 38 sec ;nope, set device not connected
00C739 1 A9 28 lda #nodev
00C73B 1 60 rts ;go back to ProDOS
00C73C 1
00C73C 1 docmd:
00C73C 1 A5 42 lda command
00C73E 1 F0 08 beq getstat ;command 0 is GetStatus
00C740 1 C9 01 cmp #$01
00C742 1 F0 0C beq readblk ;command 1 is ReadBlock
00C744 1 38 sec ;Format/Write not permitted
00C745 1 A9 2B lda #wperr ;write protect error
00C747 1 60 rts ;go back to ProDOS
00C748 1
00C748 1 getstat:
00C748 1 18 clc ;send back status
00C749 1 A9 00 lda #$00 ;good status
00C74B 1 A2 00 ldx #$00 ;1024 blocks
00C74D 1 A0 04 ldy #$04 ;
00C74F 1 60 rts
00C750 1
00C750 1 readblk:
00C750 1 A5 FA lda ioAddressLo
00C752 1 48 pha
00C753 1 A5 FB lda ioAddressHi
00C755 1 48 pha
00C756 1 A5 FC lda tempY
00C758 1 48 pha
00C759 1 A5 FD lda blockHalfCounter
00C75B 1 48 pha
00C75C 1 A5 FE lda lowLatch
00C75E 1 48 pha
00C75F 1 A5 FF lda highLatch
00C761 1 48 pha
00C762 1
00C762 1 A5 47 lda blkhi ;get hi block
00C764 1 0A asl a ;shift up to top 3 bits
00C765 1 0A asl a ;since that's all the high
00C766 1 0A asl a ;blocks we can handle
00C767 1 0A asl a ;
00C768 1 0A asl a ;
00C769 1 85 FF sta highLatch
00C76B 1 A5 46 lda blklo ;get low block
00C76D 1 4A lsr a ;shift so we get the top 5
00C76E 1 4A lsr a ;bits - this also goes in
00C76F 1 4A lsr a ;the high latch
00C770 1 05 FF ora highLatch ;add it to those top 3 bits
00C772 1 85 FF sta highLatch ;save it back in scratch ram
00C774 1 9D 81 C0 sta writeLatchHigh,x ;set high latch for card
00C777 1 A5 46 lda blklo ;get low block
00C779 1 0A asl a ;shift it to top 3 bits
00C77A 1 0A asl a ;
00C77B 1 0A asl a ;
00C77C 1 0A asl a ;
00C77D 1 0A asl a ;
00C77E 1 85 FE sta lowLatch
00C780 1 A9 02 lda #$02
00C782 1 85 FD sta blockHalfCounter
00C784 1 A9 C0 lda #$C0
00C786 1 85 FB sta ioAddressHi
00C788 1
00C788 1 ;This gets 256 bytes from the ROM card
00C788 1
00C788 1 read256:
00C788 1 A0 00 ldy #$00
00C78A 1 loop256:
00C78A 1 A5 FE lda lowLatch
00C78C 1 9D 80 C0 sta writeLatchLow,x
00C78F 1 8A txa
00C790 1 09 80 ora #$80
00C792 1 85 FA sta ioAddressLo
00C794 1
00C794 1 loop16:
00C794 1 84 FC sty tempY
00C796 1 A0 00 ldy #$00
00C798 1 B1 FA lda (ioAddressLo),y
00C79A 1 A4 FC ldy tempY
00C79C 1 91 44 sta (buflo),y
00C79E 1 C8 iny
00C79F 1 E6 FA inc ioAddressLo
00C7A1 1 A5 FA lda ioAddressLo
00C7A3 1 29 0F and #$0F
00C7A5 1 D0 ED bne loop16
00C7A7 1
00C7A7 1 continue256:
00C7A7 1 E6 FE inc lowLatch
00C7A9 1 C0 00 cpy #$00
00C7AB 1 D0 DD bne loop256
00C7AD 1 C6 FD dec blockHalfCounter
00C7AF 1 D0 18 bne readnext256
00C7B1 1
00C7B1 1 finish:
00C7B1 1 68 pla
00C7B2 1 85 FF sta highLatch
00C7B4 1 68 pla
00C7B5 1 85 FE sta lowLatch
00C7B7 1 68 pla
00C7B8 1 85 FD sta blockHalfCounter
00C7BA 1 68 pla
00C7BB 1 85 FC sta tempY
00C7BD 1 68 pla
00C7BE 1 85 FB sta ioAddressHi
00C7C0 1 68 pla
00C7C1 1 85 FA sta ioAddressLo
00C7C3 1
00C7C3 1 C6 45 dec bufhi
00C7C5 1 18 clc ;clear error code for success
00C7C6 1 A9 00 lda #$00
00C7C8 1 60 rts
00C7C9 1
00C7C9 1 readnext256:
00C7C9 1 E6 45 inc bufhi ; set buffer to receive next 256 bytes
00C7CB 1 18 clc ; effectively a branch always
00C7CC 1 90 BA bcc read256
00C7CE 1
00C7CE 1 ;macro for string with high-bit set
00C7CE 1 .macro aschi str
00C7CE 1 .repeat .strlen (str), c
00C7CE 1 .byte .strat (str, c) | $80
00C7CE 1 .endrep
00C7CE 1 .endmacro
00C7CE 1
00C7CE 1 D2 CF CD AD text: aschi "ROM-Drive (c)1998-2022 Terence J. Boldt"
00C7D2 1 C4 F2 E9 F6
00C7D6 1 E5 A0 A8 E3
00C7DA 1 A9 B1 B9 B9
00C7DE 1 B8 AD B2 B0
00C7E2 1 B2 B2 A0 D4
00C7E6 1 E5 F2 E5 EE
00C7EA 1 E3 E5 A0 CA
00C7EE 1 AE A0 C2 EF
00C7F2 1 EC E4 F4
00C7F5 1 end:
00C7F5 1 00 .byte 0
00C7F6 1
00C7F6 1 ; These bytes need to be at the top of the 256 byte firmware as ProDOS
00C7F6 1 ; uses these to find the entry point and drive capabilities
00C7F6 1
00C7F6 1 00 00 00 00 .repeat 251-<end
00C7FA 1 00 00
00C7FC 1 .byte 0
00C7FC 1 .endrepeat
00C7FC 1
00C7FC 1 00 00 .byte 0,0 ;0000 blocks = check status
00C7FE 1 03 .byte 3 ;bit 0=read 1=status
00C7FF 1 34 .byte <entry ;low byte of entry
00C7FF 1