Apple-1 Serial Interface
Go to file
2021-03-10 11:54:04 +01:00
firmware hardware recognition memory addresses added, fixed apple-1 to remote test program 2021-01-07 23:32:09 +01:00
gerber Added gerber files 2021-03-10 11:54:04 +01:00
mapping fixed pins configuration on address decoder && limited ROM address space 2021-03-04 23:20:08 +01:00
src changed assembly source files extension to *.a65 2021-02-06 23:28:49 +01:00
.gitignore First commit 2020-05-22 09:55:24 +02:00
apple1serial.jpg Added hardware installation section to README.md 2021-03-04 21:26:58 +01:00
LICENSE Create LICENSE 2021-03-04 23:21:01 +01:00
Makefile changed assembly source files extension to *.a65 2021-02-06 23:28:49 +01:00
README.md Added gerber files 2021-03-10 11:54:04 +01:00

apple1serial

apple1serial

This repository contains firmware files for the Apple-1 Serial Interface expansion card.

Description

This project aims to provide an alternative to the ACI for the Apple-1 computer via use of the serial communication (9600/8-N-1). The expansion card is based around ATMega328P MCU which operates as half-duplex UART. The signal levels are TTL, so adapter boards may be required if you need some other standard. The best way to connect the device to a regular modern PC is to use one of those cheap FTDI FT232RL USB dongles available everywhere.

Memory map

address function
$C0FC-$C0FF these addresses contain the 'A1SI' string which might be used to determine whether the A1SI expansion card is present
$C100-$C7FF address space reserved for on-board ROM
$C100 the original ACI loader program adapted to the A1SI
$C300 "teletype on apple-1" test program - the data from remote terminal appears on Apple-1 screen
$C400 "teletype on remote" test program - the data from Apple-1 appears on remote terminal
$C500 0-255 repeating counter - all possible bytes are repeatedly sent to remote terminal
$C600 serialmonitor - the well known Woz Monitor, but now on the remote terminal

entries for programmers:

address function
$C000 ready flag - contains 0x01 if the device is ready to write/read, 0x00 otherwise
$C080 read address - the location for data read from the interface, first read of this address switches the device to read mode
$C081 write address - the location for data to be written via the interface, first write to this address switches the device to write mode
$C23A software reset routine - resets the MCU
$C1EC block read routine - reads data from the interface to the specified address range
$C213 block write routine - writes the data from the specified address range via the interface
$0034 lower byte of the end address for block read/write routines
$0035 upper byte of the end address for block read/write routines
$0036 lower byte of the beginning address for block read/write routines
$0037 upper byte of the beginning address for block read/write routines

Contents

The contents of this repository are as following:

  • gerber/ - gerber files needed to manufacture the PCB
  • firmware/ - contains source code for the ATMega328 MCU firmware
  • mapping/ - contains EQN and JED files for GAL20V8 based address decoder for the board
  • src/ - contains the 6502 assembly sources for the A1SI onboard ROM routines

Requirements

You need the following to successfully build the firmware:

  • xa cross assembler
  • avr-gcc toolchain
  • avr-libc set of libraries
  • AVRDUDE AVR programmer software or equivalent to program the ATMega328P MCU
  • Some software capable of translating the EQN files into JED's. I used for this purpose the DOS based EQN2JED from OPALjr PLD Development Package. This is only required if you wish to make some changes to the GAL based address decoder. The default JED file should be fine for most users.
  • EEPROM programmer. I used TL866 programmer for this purpose. It can also program the ATMega328P MCU.

How to build?

To build the firmware just type:

make

And to clean the build:

make clean

PCB

The KiCad project files with board design and schematics can be found here:

http://github.com/flowenol/Apple1SerialPcb

Applesoft BASIC support

You can also LOAD and SAVE your Applesoft BASIC programs thanks to the branch of the applesoft-lite project which has been modified to make use of the A1SI expansion card:

http://github.com/flowenol/applesoft-lite

How to install hardware?

Solder the "C" memory segment line near 74154 demultiplexer to the "T" signal line. Afterwards just put the board in right orientation (as marked on the PCB) in the Apple-1 expansion slot. Or you can use the port expander if the on board slot is already occupied:

https://github.com/flowenol/Apple1ExpanderPcb