SD card based ProFile replacement for IIe
Go to file
2017-11-01 16:50:56 +01:00
Datasheets Merge remote-tracking branch 'origin/devel' into devel 2017-10-05 23:12:47 +02:00
Hardware IRQ Pin removed, A11 added 2017-10-16 21:42:57 +02:00
Images AddressDecoder testbench 2017-10-12 20:37:37 +02:00
VHDL SPI Mode 3 2017-11-01 16:50:56 +01:00
.gitattributes Update .gitattributes 2017-08-02 19:50:12 +02:00
.gitignore Reset inited on card remove 2017-09-10 14:07:23 +02:00
AppleIISd.bin Save and restore ZP locations 2017-11-01 16:22:35 +01:00
AppleIISd.bom.txt Schematic as PDF and BOM 2017-08-24 17:39:23 +02:00
AppleIISd.hex Save and restore ZP locations 2017-11-01 16:22:35 +01:00
AppleIISd.json Timing diagram added 2017-10-09 08:49:22 +02:00
AppleIISd.lst Save and restore ZP locations 2017-11-01 16:22:35 +01:00
AppleIISd.pdf Schematic as PDF and BOM 2017-08-24 17:39:23 +02:00
AppleIISd.s Save and restore ZP locations 2017-11-01 16:22:35 +01:00
README.md Support for second partition, card detect and write protect added 2017-09-09 20:34:24 +02:00

Apple][Sd

SD card based ProFile replacement for enhanced Apple IIe computers

The Apple][Sd is a SD card based replaced for the ProFile harddrive. In contrast to other SD card based devices, this card does not replace a Disk II drive. Data is saved directly onto the SD card, not via images on a FAT system, like on other cards. The SD card is accessable with CiderPress.

A Xilinx CPLD is used as a SPI controller and translates, together with the ROM driver, SD card data to/from the Apple IIe. The VHDL source is based on SPI65/B by André Fachat.

The assembler sources were written in Merlin-8. The schematics are available as PDF.

Features

  • up to 64MB storage space (2x 65535 blocks)
  • ProDOS driver in ROM
  • Auto boot
  • Access LED
  • Card detect and write protect sensing

Requirements

The Apple][Sd requires and has been tested on an enhanced IIe computer. The ROM code uses some 65c02 opcodes and will therefore not work on a II, II+ or unenhanced IIe. ProDOS versions 1.1 to 2.4.1 seem to work.

When a 2732 type ROM is used, the binary image has to be programmed at offset 0x800, because A11 is always high for compatibility with 2716 type ROMs.

Timing

The clock of the SPI bus SCK may be derived from either Phi0 or the 7M clock. Additionally, the divisor may be 2 to 8.

The following measurements were taken with the divisor set to 2, resulting in fSCK of 500kHz and 3.5MHz. Reading of a byte requires that a dummy byte is sent on the bus, before the answer can be read. Therefore the measurement is the time between sending the byte and receiving the answer. The measurement for reading of a whole 512 byte block includes the SD card commands to do so.

Clock Byte Block Image
Phi0 17.7µs 28.8ms Byte, Block
7M 3.9µs 15ms Byte, Block

This shows that the required to read a single byte can be reduced significantly by increasing fSCK (as one might have guessed). Reading at 500kHz actualy requires NOPs to be inserted (or checking the TC bit in the STATUS register), while reading at 3.5MHz can be done immediately.

The time for reading a 512 byte block could only be halved, but there are for sure opportunities for optimization in the code surrounding the reading.

* single byte @ 500kHz
LDA #$FF
STA $C0C0
NOP
NOP
NOP
NOP
NOP
NOP
NOP
LDA $C0C0

* single byte @ 3.5MHz
LDA #$FF
STA $C0C0
LDA $C0C0

TODOs

  • Much more testing
  • SRAM option (may never work, though)
  • Find a use for the IRQ pin
  • Use 28 pin socket to support other EPROMS than 2716 and 2732

Known Bugs

  • Does not always boot in slot 7 (may be a faulty connector, though)
  • Does not work, when a Z80 card is present

Front_Img