mirror of
https://github.com/garrettsworkshop/RAM2E.git
synced 2024-11-24 15:31:38 +00:00
832 lines
28 KiB
Verilog
832 lines
28 KiB
Verilog
module RAM2E(C14M, PHI1, LED,
|
|
nWE, nWE80, nEN80, nC07X,
|
|
Ain, Din, Dout, nDOE, Vout, nVOE,
|
|
CKE, nCS, nRAS, nCAS, nRWE,
|
|
BA, RA, RD, DQML, DQMH);
|
|
|
|
/* Clocks */
|
|
input C14M, PHI1;
|
|
|
|
/* Control inputs */
|
|
input nWE, nWE80, nEN80, nC07X;
|
|
|
|
/* Delay for EN80 signal */
|
|
//output DelayOut = 1'b0;
|
|
//input DelayIn;
|
|
wire EN80 = !nEN80;
|
|
|
|
/* Activity LED */
|
|
reg LEDEN = 0;
|
|
output LED;
|
|
assign LED = !(!nEN80 && LEDEN);
|
|
|
|
/* Address Bus */
|
|
input [7:0] Ain; // Multiplexed DRAM address input
|
|
|
|
/* 6502 Data Bus */
|
|
input [7:0] Din; // 6502 data bus inputs
|
|
reg DOEEN = 0; // 6502 data bus output enable from state machine
|
|
output nDOE;
|
|
assign nDOE = !(EN80 && nWE && DOEEN); // 6502 data bus output enable
|
|
output reg [7:0] Dout; // 6502 data Bus output
|
|
|
|
/* Video Data Bus */
|
|
output nVOE;
|
|
assign nVOE = !(!PHI1); /// Video data bus output enable
|
|
output reg [7:0] Vout; // Video data bus
|
|
|
|
/* SDRAM */
|
|
output reg CKE = 0;
|
|
output reg nCS = 1, nRAS = 1, nCAS = 1, nRWE = 1;
|
|
output reg [1:0] BA;
|
|
output reg [11:0] RA;
|
|
output reg DQML = 1, DQMH = 1;
|
|
wire RDOE = EN80 && !nWE80;
|
|
inout [7:0] RD;
|
|
assign RD[7:0] = RDOE ? Din[7:0] : 8'bZ;
|
|
|
|
/* RAMWorks Bank Register and Capacity Mask */
|
|
reg [7:0] RWBank = 0; // RAMWorks bank register
|
|
reg [7:0] RWMask = 0; // RAMWorks bank reg. capacity mask
|
|
reg RWSel = 0; // RAMWorks bank register select
|
|
reg CmdRWMaskSet = 0; // RAMWorks Mask register set flag
|
|
// Causes RWBank to be zeroed next RWSel access
|
|
//reg CmdSetRWBankFFMAX = 0;
|
|
//reg CmdSetRWBankFFSPI = 0;
|
|
reg CmdSetRWBankFFMXO2 = 0;
|
|
reg CmdSetRWBankFFLED = 0;
|
|
reg CmdLEDSet = 0;
|
|
reg CmdLEDGet = 0;
|
|
|
|
/* Command Sequence Detector */
|
|
reg [2:0] CS = 0; // Command sequence state
|
|
reg [2:0] CmdTout = 0; // Command sequence timeout
|
|
|
|
/* UFM Interface */
|
|
reg wb_rst;
|
|
reg wb_cyc_stb;
|
|
reg wb_req;
|
|
reg wb_we;
|
|
reg [7:0] wb_adr;
|
|
reg [7:0] wb_dati;
|
|
wire wb_ack;
|
|
wire [7:0] wb_dato;
|
|
wire ufm_irq;
|
|
REFB ufmefb(
|
|
.wb_clk_i(C14M),
|
|
.wb_rst_i(wb_rst),
|
|
.wb_cyc_i(wb_cyc_stb),
|
|
.wb_stb_i(wb_cyc_stb),
|
|
.wb_we_i(wb_we),
|
|
.wb_adr_i(wb_adr),
|
|
.wb_dat_i(wb_dati),
|
|
.wb_dat_o(wb_dato),
|
|
.wb_ack_o(wb_ack),
|
|
.wbc_ufm_irq(ufm_irq));
|
|
|
|
/* UFM State and User Command Triggers */
|
|
//reg CmdBitbangMAX = 0; // Set by user command. Loads UFM outputs next RWSel
|
|
//reg CmdBitbangSPI = 0;
|
|
reg CmdBitbangMXO2 = 0;
|
|
reg CmdExecMXO2 = 0;
|
|
//reg CmdPrgmMAX = 0; // Set by user command. Programs UFM
|
|
//reg CmdEraseMAX = 0; // Set by user command. Erases UFM
|
|
|
|
/* State Counters */
|
|
reg PHI1reg = 0; // Saved PHI1 at last rising clock edge
|
|
reg Ready = 0; // 1 if done with init sequence (S0) and enter S1-S15
|
|
reg [15:0] FS = 0; // Fast state counter
|
|
reg [3:0] S = 0; // IIe State counter
|
|
|
|
/* State Counters */
|
|
always @(posedge C14M) begin
|
|
// Increment fast state counter
|
|
FS <= FS+16'h0001;
|
|
// Synchronize Apple state counter to S1 when just entering PHI1
|
|
PHI1reg <= PHI1; // Save old PHI1
|
|
S <= (PHI1 && !PHI1reg && Ready) ? 4'h1 :
|
|
S==4'h0 ? 4'h0 :
|
|
S==4'hF ? 4'hF : S+4'h1;
|
|
end
|
|
|
|
/* UFM Control */
|
|
always @(posedge C14M) begin
|
|
if (S==4'h0) begin
|
|
if (FS[15:14]==2'b00) wb_rst <= 1'b1;
|
|
else if (FS[15:14]==2'b01) wb_rst <= 1'b0;
|
|
else if (FS[15:14]==2'b10) begin
|
|
wb_rst <= 1'b0;
|
|
if (wb_ack || (FS[7:0]==0)) wb_cyc_stb <= 0;
|
|
else if ((FS[7:0]==1) && wb_req) wb_cyc_stb <= 1;
|
|
case (FS[13:8])
|
|
0: begin // Open frame
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h70;
|
|
wb_dati[7:0] <= 8'h80;
|
|
wb_req <= 1;
|
|
end 1: begin // Enable configuration interface - command
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h74;
|
|
wb_req <= 1;
|
|
end 2: begin // Enable configuration interface - operand 1/3
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h08;
|
|
wb_req <= 1;
|
|
end 3: begin // Enable configuration interface - operand 2/3
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 4: begin // Enable configuration interface - operand 3/3
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 5: begin // Close frame
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h70;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
|
|
end 6: begin // Open frame
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h70;
|
|
wb_dati[7:0] <= 8'h80;
|
|
wb_req <= 1;
|
|
end 7: begin // Poll status register - command
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h3C;
|
|
wb_req <= 1;
|
|
end 8: begin // Poll status register - operand 1/3
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 9: begin // Poll status register - operand 2/3
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 10: begin // Poll status register - operand 3/3
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 11, 12, 13, 14: begin // Read status register 1-4
|
|
wb_we <= 1'b0;
|
|
wb_adr[7:0] <= 8'h73;
|
|
wb_dati[7:0] <= 8'h3C;
|
|
wb_req <= 1;
|
|
end 15: begin // Close frame
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h70;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
|
|
end 16: begin // Open frame
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h70;
|
|
wb_dati[7:0] <= 8'h80;
|
|
wb_req <= 1;
|
|
end 17: begin // Set UFM address - command
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'hB4;
|
|
wb_req <= 1;
|
|
end 18: begin // Set UFM address - operand 1/3
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 19: begin // Set UFM address - operand 2/3
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 20: begin // Set UFM address - operand 3/3
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 21: begin // Set UFM address - data 1/4
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h40;
|
|
wb_req <= 1;
|
|
end 22: begin // Set UFM address - data 2/4
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 23: begin // Set UFM address - data 3/4
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 24: begin // Set UFM address - data 4/4
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 190;
|
|
wb_req <= 1;
|
|
end 25: begin // Close frame
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h70;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
|
|
end 26: begin // Open frame
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h70;
|
|
wb_dati[7:0] <= 8'h80;
|
|
wb_req <= 1;
|
|
end 27: begin // Read UFM page - command
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'hCA;
|
|
wb_req <= 1;
|
|
end 28: begin // Read UFM page - operand 1/3
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h10;
|
|
wb_req <= 1;
|
|
end 29: begin // Read UFM page - operand 2/3
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 30: begin // Read UFM page - operand 3/3
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h01;
|
|
wb_req <= 1;
|
|
end 31: begin // Read UFM page - data 0
|
|
wb_we <= 1'b0;
|
|
wb_adr[7:0] <= 8'h73;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
if (wb_ack) RWMask[7:0] <= wb_dato[7:0];
|
|
end 32: begin // Read UFM page - data 1
|
|
wb_we <= 1'b0;
|
|
wb_adr[7:0] <= 8'h73;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
if (wb_ack) LEDEN <= wb_dato[0];
|
|
end 33, 34,
|
|
35, 36, 37, 38,
|
|
39, 40, 41, 42,
|
|
43, 44, 45, 46: begin // Read UFM page - data 2-15
|
|
wb_we <= 1'b0;
|
|
wb_adr[7:0] <= 8'h73;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 47: begin // Close frame
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h70;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
|
|
end 48: begin // Open frame
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h70;
|
|
wb_dati[7:0] <= 8'h80;
|
|
wb_req <= 1;
|
|
end 49: begin // Disable configuration interface - command
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h26;
|
|
wb_req <= 1;
|
|
end 50: begin // Disable configuration interface - operand 1/2
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 51: begin // Disable configuration interface - operand 2/2
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end 52: begin // Close frame
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h70;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
|
|
end 53: begin // Open frame
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h70;
|
|
wb_dati[7:0] <= 8'h80;
|
|
wb_req <= 1;
|
|
end 54: begin // Bypass - command
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h71;
|
|
wb_dati[7:0] <= 8'hFF;
|
|
wb_req <= 1;
|
|
end 55: begin // Close frame
|
|
wb_we <= 1'b1;
|
|
wb_adr[7:0] <= 8'h70;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 1;
|
|
end default: begin
|
|
wb_we <= 1'b0;
|
|
wb_adr[7:0] <= 8'h70;
|
|
wb_dati[7:0] <= 8'h00;
|
|
wb_req <= 0;
|
|
end
|
|
endcase
|
|
end else begin
|
|
wb_rst <= 1'b0;
|
|
wb_cyc_stb <= 1'b0;
|
|
wb_req <= 1'b0;
|
|
wb_we <= 1'b0;
|
|
wb_adr[7:0] <= 8'h00;
|
|
wb_dati[7:0] <= 8'h00;
|
|
end
|
|
end else begin
|
|
// UFM bitbang control
|
|
wb_rst <= 1'b0;
|
|
wb_req <= 1'b0;
|
|
|
|
if (RWSel && S==4'hC) begin
|
|
// LED control
|
|
if (CmdLEDSet) LEDEN <= Din[0];
|
|
|
|
// Set capacity mask
|
|
if (CmdRWMaskSet) RWMask[7:0] <= {Din[7], ~Din[6:0]};
|
|
|
|
// Set EFB address
|
|
if (CmdBitbangMXO2) begin
|
|
wb_adr[7:0] <= Din[7:0];
|
|
wb_dati[7:0] <= wb_adr[7:0];
|
|
end
|
|
|
|
// Excecute EFB R/W cycle
|
|
if (CmdExecMXO2) begin
|
|
wb_we <= Din[0];
|
|
wb_cyc_stb <= 1;
|
|
end else if (wb_ack) wb_cyc_stb <= 0;
|
|
end
|
|
end
|
|
end
|
|
|
|
/* SDRAM Control */
|
|
always @(posedge C14M) begin
|
|
if (S==4'h0) begin
|
|
// SDRAM initialization
|
|
if (FS[15:0]==16'hFFC0) begin
|
|
// Precharge All
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b0;
|
|
RA[10] <= 1'b1; // "all"
|
|
end else if (FS[15:4]==16'hFFD && FS[0]==1'b0) begin // Repeat 8x
|
|
// Auto-refresh
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b0;
|
|
nRWE <= 1'b1;
|
|
RA[10] <= 1'b0;
|
|
end else if (FS[15:0]==16'hFFE8) begin
|
|
// Set Mode Register
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b0;
|
|
nRWE <= 1'b0;
|
|
RA[10] <= 1'b0; // Reserved in mode register
|
|
end else if (FS[15:4]==12'hFFF && FS[0]==1'b0) begin // Repeat 8x
|
|
// Auto-refresh
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b0;
|
|
nRWE <= 1'b1;
|
|
RA[10] <= 1'b0;
|
|
end else begin // Otherwise send no-op
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
RA[10] <= 1'b0;
|
|
end
|
|
// Enable SDRAM clock after 65,280 cycles (~4.56ms)
|
|
CKE <= FS[15:8] == 8'hFF;
|
|
|
|
// Mode register contents
|
|
BA[1:0] <= 2'b00; // Reserved
|
|
RA[11] <= 1'b0; // Reserved
|
|
// RA[10] set above ^
|
|
RA[9] <= 1'b1; // "1" for single write mode
|
|
RA[8] <= 1'b0; // Reserved
|
|
RA[7] <= 1'b0; // "0" for not test mode
|
|
RA[6:4] <= 3'b010; // "2" for CAS latency 2
|
|
RA[3] <= 1'b0; // "0" for sequential burst (not used)
|
|
RA[2:0] <= 3'b000; // "0" for burst length 1 (no burst)
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
|
|
// Begin normal operation after 128k init cycles (~9.15ms)
|
|
if (FS == 16'hFFFF) Ready <= 1'b1;
|
|
end else if (S==4'h1) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA[1:0] <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h2) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
// Activate
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// SDRAM bank 0, high-order row address is 0
|
|
BA[1:0] <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
// Row address is as previously latched
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h3) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
// Read
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b0;
|
|
nRWE <= 1'b1;
|
|
|
|
// SDRAM bank 0, RA[11,9:8] don't care
|
|
BA[1:0] <= 2'b00;
|
|
RA[11] <= 1'b0;
|
|
RA[10] <= 1'b1; // (A10 set to auto-precharge)
|
|
RA[9] <= 1'b0;
|
|
RA[8] <= 1'b0;
|
|
// Latch column address for read command
|
|
RA[7:0] <= Ain[7:0];
|
|
|
|
// Read low byte (high byte is +4MB in ramworks)
|
|
DQML <= 1'b0;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h4) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA[1:0] <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h5) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA[1:0] <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h6) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
if (FS[5:4]==0) begin
|
|
// Auto-refresh
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b0;
|
|
nRWE <= 1'b1;
|
|
end else begin
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
end
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA[1:0] <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h7) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA[1:0] <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
// Latch row address for activate command
|
|
RA[7:0] <= Ain[7:0];
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h8) begin
|
|
// Enable clock if '245 output enabled
|
|
CKE <= EN80;
|
|
|
|
// Activate if '245 output enabled
|
|
nCS <= nEN80;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// SDRAM bank, RA[11:8] determine by RamWorks bank
|
|
BA[1:0] <= RWBank[5:4];
|
|
RA[11:8] <= RWBank[3:0];
|
|
// Row address is as previously latched
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h9) begin
|
|
// Enable clock if '245 output enabled
|
|
CKE <= EN80;
|
|
|
|
// Read/Write if '245 output enabled
|
|
nCS <= nEN80;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b0;
|
|
nRWE <= nWE80;
|
|
|
|
// SDRAM bank still determined by RamWorks, RA[11,9:8] don't care
|
|
BA[1:0] <= RWBank[5:4];
|
|
RA[11] <= 1'b0;
|
|
RA[10] <= 1'b1; // (A10 set to auto-precharge)
|
|
RA[9] <= 1'b0;
|
|
RA[8] <= RWBank[7];
|
|
// Latch column address for R/W command
|
|
RA[7:0] <= Ain[7:0];
|
|
|
|
// Latch RAMWorks low nybble write select using old row address
|
|
RWSel <= RA[0] && !RA[3] && !nWE && !nC07X;
|
|
|
|
// Mask according to RAMWorks bank (high byte is +4MB)
|
|
DQML <= RWBank[6];
|
|
DQMH <= !RWBank[6];
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'hA) begin
|
|
// Enable clock if '245 output enabled
|
|
CKE <= EN80;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA[1:0] <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'hB) begin
|
|
// Disable clock
|
|
CKE <= 1'b0;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA[1:0] <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Enable data bus output
|
|
DOEEN <= 1'b1;
|
|
end else if (S==4'hC) begin
|
|
// Disable clock
|
|
CKE <= 1'b0;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA[1:0] <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Enable data bus output
|
|
DOEEN <= 1'b1;
|
|
|
|
// RAMWorks Bank Register Select
|
|
if (RWSel) begin
|
|
// Latch RAMWorks bank if accessed
|
|
if (CmdSetRWBankFFLED ||
|
|
//CmdSetRWBankFFMAX ||
|
|
//CmdSetRWBankFFSPI ||
|
|
CmdSetRWBankFFMXO2 ||
|
|
(CmdLEDGet && LEDEN)) RWBank <= 8'hFF;
|
|
else RWBank <= Din[7:0] & {RWMask[7], ~RWMask[6:0]};
|
|
|
|
// Recognize command sequence and advance CS state
|
|
if ((CS==3'h0 && Din[7:0]==8'hFF) ||
|
|
(CS==3'h1 && Din[7:0]==8'h00) ||
|
|
(CS==3'h2 && Din[7:0]==8'h55) ||
|
|
(CS==3'h3 && Din[7:0]==8'hAA) ||
|
|
(CS==3'h4 && Din[7:0]==8'hC1) ||
|
|
(CS==3'h5 && Din[7:0]==8'hAD) ||
|
|
CS==3'h6 || CS==3'h7) CS <= CS+3'h1;
|
|
else CS <= 0; // Back to beginning if it's not right
|
|
|
|
if (CS==3'h6) begin // Recognize and submit command in CS6
|
|
//CmdSetRWBankFFMAX <= Din[7:0]==8'hFF;
|
|
//CmdSetRWBankFFSPI <= Din[7:0]==8'hFE;
|
|
CmdSetRWBankFFMXO2 <= Din[7:0]==8'hFD;
|
|
CmdSetRWBankFFLED <= Din[7:0]==8'hF0;
|
|
|
|
CmdRWMaskSet <= Din[7:0]==8'hE0;
|
|
CmdLEDSet <= Din[7:0]==8'hE2;
|
|
CmdLEDGet <= Din[7:0]==8'hE3;
|
|
|
|
//CmdBitbangMAX <= Din[7:0]==8'hEA;
|
|
//CmdBitbangSPI <= Din[7:0]==8'hEB;
|
|
CmdBitbangMXO2 <= Din[7:0]==8'hEC;
|
|
CmdExecMXO2 <= Din[7:0]==8'hED;
|
|
|
|
//if (Din[7:0]==8'hEE) CmdEraseMAX <= 1;
|
|
//if (Din[7:0]==8'hEF) CmdPrgmMAX <= 1;
|
|
end else begin // Reset command triggers
|
|
//CmdSetRWBankFFMAX <= 0;
|
|
//CmdSetRWBankFFSPI <= 0;
|
|
CmdSetRWBankFFMXO2 <= 0;
|
|
CmdSetRWBankFFLED <= 0;
|
|
CmdRWMaskSet <= 0;
|
|
CmdLEDSet <= 0;
|
|
CmdLEDGet <= 0;
|
|
//CmdBitbangMAX <= 0;
|
|
//CmdBitbangSPI <= 0;
|
|
CmdBitbangMXO2 <= 0;
|
|
CmdExecMXO2 <= 0;
|
|
end
|
|
|
|
CmdTout <= 0; // Reset command timeout if RWSel accessed
|
|
end else begin
|
|
CmdTout <= CmdTout+3'h1; // Increment command timeout
|
|
// If command sequence times out, reset sequence state
|
|
if (CmdTout==3'h7) CS <= 0;
|
|
end
|
|
end else if (S==4'hD) begin
|
|
// Disable clock
|
|
CKE <= 1'b0;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA[1:0] <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Enable data bus output
|
|
DOEEN <= 1'b1;
|
|
end else if (S==4'hE) begin
|
|
// Disable clock
|
|
CKE <= 1'b0;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA[1:0] <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
// Latch row address for next video read
|
|
RA[7:0] <= Ain[7:0];
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Enable data bus output
|
|
DOEEN <= 1'b1;
|
|
end else if (S==4'hF) begin
|
|
// Disable clock
|
|
CKE <= 1'b0;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA[1:0] <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
// Latch row address for next video read
|
|
RA[7:0] <= Ain[7:0];
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Enable data bus output
|
|
DOEEN <= 1'b1;
|
|
end
|
|
end
|
|
always @(negedge C14M) begin
|
|
// Latch video and read data outputs
|
|
if (S==4'h6) Vout[7:0] <= RD[7:0];
|
|
if (S==4'hC) Dout[7:0] <= RD[7:0];
|
|
end
|
|
endmodule
|