mirror of
https://github.com/garrettsworkshop/RAM2E.git
synced 2024-11-25 06:31:29 +00:00
637 lines
21 KiB
Verilog
637 lines
21 KiB
Verilog
module RAM2E(C14M, PHI1,
|
|
nWE, nWE80, nEN80, nC07X,
|
|
Ain, Din, Dout, nDOE, Vout, nVOE,
|
|
CKE, nCS, nRAS, nCAS, nRWE,
|
|
BA, RA, RD, DQML, DQMH);
|
|
|
|
/* Clocks */
|
|
input C14M, PHI1;
|
|
|
|
/* Control inputs */
|
|
input nWE, nWE80, nEN80, nC07X;
|
|
|
|
/* Delay for EN80 signal */
|
|
//output DelayOut = 1'b0;
|
|
//input DelayIn;
|
|
wire EN80 = ~nEN80;
|
|
|
|
/* Address Bus */
|
|
input [7:0] Ain; // Multiplexed DRAM address input
|
|
|
|
/* 6502 Data Bus */
|
|
input [7:0] Din; // 6502 data bus inputs
|
|
reg DOEEN = 0; // 6502 data bus output enable from state machine
|
|
output nDOE = ~(EN80 & nWE & DOEEN); // 6502 data bus output enable
|
|
output reg [7:0] Dout; // 6502 data Bus output
|
|
|
|
/* Video Data Bus */
|
|
output nVOE = ~(~PHI1); /// Video data bus output enable
|
|
output reg [7:0] Vout; // Video data bus
|
|
|
|
/* SDRAM */
|
|
output reg CKE = 0;
|
|
output reg nCS = 1, nRAS = 1, nCAS = 1, nRWE = 1;
|
|
output reg [1:0] BA;
|
|
output reg [11:0] RA;
|
|
output reg DQML = 1, DQMH = 1;
|
|
wire RDOE = EN80 & ~nWE80;
|
|
inout [7:0] RD = RDOE ? Din[7:0] : 8'bZ;
|
|
|
|
/* RAMWorks Bank Register and Capacity Mask */
|
|
reg [7:0] RWBank = 0; // RAMWorks bank register
|
|
reg [7:0] RWMask = 0; // RAMWorks bank reg. capacity mask
|
|
reg RWSel = 0; // RAMWorks bank register select
|
|
reg RWMaskSet = 0; // RAMWorks Mask register set flag
|
|
reg SetRWBankFF = 0; // Causes RWBank to be zeroed next RWSel access
|
|
|
|
/* Command Sequence Detector */
|
|
reg [2:0] CS = 0; // Command sequence state
|
|
reg [2:0] CmdTout = 0; // Command sequence timeout
|
|
|
|
/* UFM Interface */
|
|
reg [15:8] UFMD = 0; // *Parallel* UFM data register
|
|
reg ARCLK = 0; // UFM address register clock
|
|
// UFM address register data input tied to 0
|
|
reg ARShift = 0; // 1 to Shift UFM address in, 0 to increment
|
|
reg DRCLK = 0; // UFM data register clock
|
|
reg DRDIn = 0; // UFM data register input
|
|
reg DRShift = 0; // 1 to shift UFM out, 0 to load from current address
|
|
reg UFMErase = 0; // Rising edge starts erase. UFM+RTP must not be busy
|
|
reg UFMProgram = 0; // Rising edge starts program. UFM+RTP must not be busy
|
|
wire UFMBusy; // 1 if UFM is doing user operation. Asynchronous
|
|
wire RTPBusy; // 1 if real-time programming in progress. Asynchronous
|
|
wire DRDOut; // UFM data output
|
|
// UFM oscillator always enabled
|
|
wire UFMOsc; // UFM oscillator output (3.3-5.5 MHz)
|
|
UFM UFM_inst ( // UFM IP block (for Altera MAX II and MAX V)
|
|
.arclk (ARCLK),
|
|
.ardin (1'b0),
|
|
.arshft (ARShift),
|
|
.drclk (DRCLK),
|
|
.drdin (DRDIn),
|
|
.drshft (DRShift),
|
|
.erase (UFMErase),
|
|
.oscena (1'b1),
|
|
.program (UFMProgram),
|
|
.busy (UFMBusy),
|
|
.drdout (DRDOut),
|
|
.osc (UFMOsc),
|
|
.rtpbusy (RTPBusy));
|
|
reg UFMBusyReg = 0; // UFMBusy registered to sync with C14M
|
|
reg RTPBusyReg = 0; // RTPBusy registered to sync with C14M
|
|
|
|
/* UFM State & User Command Triggers */
|
|
reg UFMInitDone = 0; // 1 if UFM initialization finished
|
|
reg UFMReqErase = 0; // 1 if UFM requires erase
|
|
reg UFMBitbang = 0; // Set by user command. Loads UFM outputs next RWSel
|
|
reg UFMPrgmEN = 0; // Set by user command. Programs UFM
|
|
reg UFMEraseEN = 0; // Set by user command. Erases UFM
|
|
reg DRCLKPulse = 0; // Set by user command. Causes DRCLK pulse next C14M
|
|
|
|
/* State Counters */
|
|
reg PHI1reg = 0; // Saved PHI1 at last rising clock edge
|
|
reg Ready = 0; // 1 if done with init sequence (S0) and enter S1-S15
|
|
reg [15:0] FS = 0; // Fast state counter
|
|
reg [3:0] S = 0; // IIe State counter
|
|
|
|
/* State Counters */
|
|
always @(posedge C14M) begin
|
|
// Increment fast state counter
|
|
FS <= FS+1;
|
|
// Synchronize Apple state counter to S1 when just entering PHI1
|
|
PHI1reg <= PHI1; // Save old PHI1
|
|
S <= (PHI1 & ~PHI1reg & Ready) ? 4'h1 :
|
|
S==4'h0 ? 4'h0 :
|
|
S==4'hF ? 4'hF : S+1;
|
|
end
|
|
|
|
/* UFM Control */
|
|
always @(posedge C14M) begin
|
|
// Synchronize asynchronous UFM signals
|
|
UFMBusyReg <= UFMBusy;
|
|
RTPBusyReg <= RTPBusy;
|
|
|
|
if (S==4'h0) begin
|
|
if ((FS[15:13]==3'b101) | (FS[15:13]==3'b111 & UFMReqErase)) begin
|
|
// In states AXXX-BXXX and also EXXX-FXXX if erase/wrap req'd
|
|
// shift in 0's to address register
|
|
ARCLK <= FS[0]; // Clock address register
|
|
DRCLK <= 1'b0; // Don't clock data register
|
|
ARShift <= 1'b1; // Shift address registers
|
|
DRDIn <= 1'b0; // Don't care DRDIn
|
|
DRShift <= 1'b0; // Don't care DRDShift
|
|
end else if (~UFMInitDone & FS[15:13]==3'b110 & FS[4:1]==4'h4) begin
|
|
// In states CXXX-DXXX (substep 4)
|
|
// Xfer to data reg (repeat 256x 1x)
|
|
ARCLK <= 1'b0; // Don't clock address register
|
|
DRCLK <= FS[0]; // Clock data register
|
|
ARShift <= 1'b0; // Don't care ARShift
|
|
DRDIn <= 1'b0; // Don't care DRDIn
|
|
DRShift <= 1'b0; // Don't care DRShift
|
|
end else if (~UFMInitDone & FS[15:13]==3'b110 & FS[4]==1'b1) begin
|
|
// In states CXXX-DXXX (substeps 8-F)
|
|
// Save UFM D15-8, shift out D14-7 (repeat 256x 8x)
|
|
DRCLK <= FS[0]; // Clock data register
|
|
ARShift <= 1'b0; // ARShift is 0 because we want to increment
|
|
DRDIn <= 1'b0; // Don't care what to shift into data register
|
|
DRShift <= 1'b1; // Shift data register
|
|
// Shift into UFMD
|
|
if (FS[0]) UFMD[15:8] <= {UFMD[14:8], DRDOut};
|
|
|
|
// Compare and store mask
|
|
if (FS[4:1]==4'hF) begin
|
|
ARCLK <= FS[0]; // Clock address register to increment
|
|
// If byte is erased (0xFF, i.e. all 1's, is erased)...
|
|
if (UFMD[14:8]==7'b1111111 & DRDOut==1'b1) begin
|
|
// Current UFM address is where we want to store
|
|
UFMInitDone <= 1'b1; // Quit iterating
|
|
// Otherwise byte is valid setting (i.e. some bit is 0)...
|
|
end else begin
|
|
// Set RWMask, but if saved mask is 0x80, store ~0xFF
|
|
if (UFMD[14:8]==7'b1000000 & DRDOut==1'b0) begin
|
|
RWMask[7:0] <= {1'b1, ~7'h7F};
|
|
end else RWMask[7:0] <= {UFMD[14], ~UFMD[13:8], ~DRDOut};
|
|
// If last byte in sector...
|
|
if (FS[12:5]==8'hFF) begin
|
|
UFMReqErase <= 1'b1; // Mark need to erase
|
|
end
|
|
end
|
|
end else ARCLK <= 1'b0; // Don't clock address register
|
|
end else begin
|
|
ARCLK <= 1'b0;
|
|
DRCLK <= 1'b0;
|
|
ARShift <= 1'b0;
|
|
DRDIn <= 1'b0;
|
|
DRShift <= 1'b0;
|
|
end
|
|
|
|
// Don't erase or program UFM during initialization
|
|
UFMErase <= 1'b0;
|
|
UFMProgram <= 1'b0;
|
|
// Keep DRCLK pulse control disabled during init
|
|
DRCLKPulse <= 1'b0;
|
|
end else begin
|
|
// Can only shift UFM data register now
|
|
ARCLK <= 1'b0;
|
|
ARShift <= 1'b0;
|
|
DRShift <= 1'b1;
|
|
|
|
// UFM bitbang control
|
|
if (UFMBitbang & CS==3'h7 & RWSel & S==4'hC) begin
|
|
DRDIn <= Din[6];
|
|
DRCLKPulse <= Din[7];
|
|
DRCLK <= 1'b0;
|
|
end else begin
|
|
DRCLKPulse <= 1'b0;
|
|
DRCLK <= DRCLKPulse;
|
|
end
|
|
|
|
// Set capacity mask
|
|
if (RWMaskSet & RWSel & S==4'hC) RWMask[7:0] <= {Din[7], ~Din[6:0]};
|
|
|
|
// UFM programming sequence
|
|
if (UFMPrgmEN | UFMEraseEN) begin
|
|
if (~UFMBusyReg & ~RTPBusyReg) begin
|
|
if (UFMReqErase | UFMEraseEN) UFMErase <= 1'b1;
|
|
else if (UFMPrgmEN) UFMProgram <= 1'b1;
|
|
end else if (UFMBusyReg) UFMReqErase <= 1'b0;
|
|
end
|
|
end
|
|
end
|
|
|
|
/* SDRAM Control */
|
|
always @(posedge C14M) begin
|
|
if (S==4'h0) begin
|
|
// SDRAM initialization
|
|
if (FS[15:0]==16'hFFC0) begin
|
|
// Precharge All
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b0;
|
|
RA[10] <= 1'b1; // "all"
|
|
end else if (FS[15:4]==16'hFFD & FS[0]==1'b0) begin // Repeat 8x
|
|
// Auto-refresh
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b0;
|
|
nRWE <= 1'b1;
|
|
RA[10] <= 1'b0;
|
|
end else if (FS[15:0]==16'hFFE8) begin
|
|
// Set Mode Register
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b0;
|
|
nRWE <= 1'b0;
|
|
RA[10] <= 1'b0; // Reserved in mode register
|
|
end else if (FS[15:4]==12'hFFF & FS[0]==1'b0) begin // Repeat 8x
|
|
// Auto-refresh
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b0;
|
|
nRWE <= 1'b1;
|
|
RA[10] <= 1'b0;
|
|
end else begin // Otherwise send no-op
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
RA[10] <= 1'b0;
|
|
end
|
|
// Enable SDRAM clock after 65,280 cycles (~4.56ms)
|
|
CKE <= FS[15:8] == 8'hFF;
|
|
|
|
// Mode register contents
|
|
BA[1:0] <= 2'b00; // Reserved
|
|
RA[11] <= 1'b0; // Reserved
|
|
// RA[10] set above ^
|
|
RA[9] <= 1'b1; // "1" for single write mode
|
|
RA[8] <= 1'b0; // Reserved
|
|
RA[7] <= 1'b0; // "0" for not test mode
|
|
RA[6:4] <= 3'b010; // "2" for CAS latency 2
|
|
RA[3] <= 1'b0; // "0" for sequential burst (not used)
|
|
RA[2:0] <= 3'b000; // "0" for burst length 1 (no burst)
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
|
|
// Begin normal operation after 128k init cycles (~9.15ms)
|
|
if (FS == 16'hFFFF) Ready <= 1'b1;
|
|
end else if (S==4'h1) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h2) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
// Activate
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// SDRAM bank 0, high-order row address is 0
|
|
BA <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
// Row address is as previously latched
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h3) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
// Read
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b0;
|
|
nRWE <= 1'b1;
|
|
|
|
// SDRAM bank 0, RA[11,9:8] don't care
|
|
BA <= 2'b00;
|
|
RA[11] <= 1'b0;
|
|
RA[10] <= 1'b1; // (A10 set to auto-precharge)
|
|
RA[9] <= 1'b0;
|
|
RA[8] <= 1'b0;
|
|
// Latch column address for read command
|
|
RA[7:0] <= Ain[7:0];
|
|
|
|
// Read low byte (high byte is +4MB in ramworks)
|
|
DQML <= 1'b0;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h4) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h5) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h6) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
if (FS[5:4]==0) begin
|
|
// Auto-refresh
|
|
nCS <= 1'b0;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b0;
|
|
nRWE <= 1'b1;
|
|
end else begin
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
end
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h7) begin
|
|
// Enable clock
|
|
CKE <= 1'b1;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
// Latch row address for activate command
|
|
RA[7:0] <= Ain[7:0];
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h8) begin
|
|
// Enable clock if '245 output enabled
|
|
CKE <= EN80;
|
|
|
|
// Activate if '245 output enabled
|
|
nCS <= nEN80;
|
|
nRAS <= 1'b0;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// SDRAM bank, RA[11:8] determine by RamWorks bank
|
|
BA <= RWBank[5:4];
|
|
RA[11:8] <= RWBank[3:0];
|
|
// Row address is as previously latched
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'h9) begin
|
|
// Enable clock if '245 output enabled
|
|
CKE <= EN80;
|
|
|
|
// Read/Write if '245 output enabled
|
|
nCS <= nEN80;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b0;
|
|
nRWE <= nWE80;
|
|
|
|
// SDRAM bank still determined by RamWorks, RA[11,9:8] don't care
|
|
BA <= RWBank[5:4];
|
|
RA[11] <= 1'b0;
|
|
RA[10] <= 1'b1; // (A10 set to auto-precharge)
|
|
RA[9] <= 1'b0;
|
|
RA[8] <= RWBank[7];
|
|
// Latch column address for R/W command
|
|
RA[7:0] <= Ain[7:0];
|
|
|
|
// Latch RAMWorks low nybble write select using old row address
|
|
RWSel <= RA[0] & ~RA[3] & ~nWE & ~nC07X;
|
|
|
|
// Mask according to RAMWorks bank (high byte is +4MB)
|
|
DQML <= RWBank[6];
|
|
DQMH <= ~RWBank[6];
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'hA) begin
|
|
// Enable clock if '245 output enabled
|
|
CKE <= EN80;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Inhibit data bus output
|
|
DOEEN <= 1'b0;
|
|
end else if (S==4'hB) begin
|
|
// Disable clock
|
|
CKE <= 1'b0;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Enable data bus output
|
|
DOEEN <= 1'b1;
|
|
end else if (S==4'hC) begin
|
|
// Disable clock
|
|
CKE <= 1'b0;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Enable data bus output
|
|
DOEEN <= 1'b1;
|
|
|
|
// RAMWorks Bank Register Select
|
|
if (RWSel) begin
|
|
// Latch RAMWorks bank if accessed
|
|
if (SetRWBankFF) RWBank <= 8'hFF;
|
|
else RWBank <= Din[7:0] & {RWMask[7], ~RWMask[6:0]};
|
|
|
|
// Recognize command sequence and advance CS state
|
|
if ((CS==3'h0 & Din[7:0]==8'hFF) |
|
|
(CS==3'h1 & Din[7:0]==8'h00) |
|
|
(CS==3'h2 & Din[7:0]==8'h55) |
|
|
(CS==3'h3 & Din[7:0]==8'hAA) |
|
|
(CS==3'h4 & Din[7:0]==8'hC1) |
|
|
(CS==3'h5 & Din[7:0]==8'hAD) |
|
|
CS==3'h6 | CS==3'h7) CS <= CS+1;
|
|
else CS <= 0; // Back to beginning if it's not right
|
|
|
|
if (CS==3'h6) begin // Recognize and submit command in CS6
|
|
SetRWBankFF <= Din[7:0]==8'hFF;
|
|
if (Din[7:0]==8'hEF) UFMPrgmEN <= 1'b1;
|
|
if (Din[7:0]==8'hEE) UFMEraseEN <= 1'b1;
|
|
UFMBitbang <= Din[7:0]==8'hEA;
|
|
RWMaskSet <= Din[7:0]==8'hE0;
|
|
end else begin // Reset command triggers
|
|
SetRWBankFF <= 1'b0;
|
|
UFMBitbang <= 1'b0;
|
|
RWMaskSet <= 1'b0;
|
|
end
|
|
|
|
CmdTout <= 0; // Reset command timeout if RWSel accessed
|
|
end else begin
|
|
CmdTout <= CmdTout+1; // Increment command timeout
|
|
// If command sequence times out, reset sequence state
|
|
if (CmdTout==3'h7) CS <= 0;
|
|
end
|
|
end else if (S==4'hD) begin
|
|
// Disable clock
|
|
CKE <= 1'b0;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Enable data bus output
|
|
DOEEN <= 1'b1;
|
|
end else if (S==4'hE) begin
|
|
// Disable clock
|
|
CKE <= 1'b0;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
// Latch row address for next video read
|
|
RA[7:0] <= Ain[7:0];
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Enable data bus output
|
|
DOEEN <= 1'b1;
|
|
end else if (S==4'hF) begin
|
|
// Disable clock
|
|
CKE <= 1'b0;
|
|
|
|
// NOP
|
|
nCS <= 1'b1;
|
|
nRAS <= 1'b1;
|
|
nCAS <= 1'b1;
|
|
nRWE <= 1'b1;
|
|
|
|
// Don't care bank, RA[11:8]
|
|
BA <= 2'b00;
|
|
RA[11:8] <= 4'b0000;
|
|
// Latch row address for next video read
|
|
RA[7:0] <= Ain[7:0];
|
|
|
|
// Mask everything
|
|
DQML <= 1'b1;
|
|
DQMH <= 1'b1;
|
|
|
|
// Enable data bus output
|
|
DOEEN <= 1'b1;
|
|
end
|
|
end
|
|
always @(negedge C14M) begin
|
|
// Latch video and read data outputs
|
|
if (S==4'h6) Vout[7:0] <= RD[7:0];
|
|
if (S==4'hC) Dout[7:0] <= RD[7:0];
|
|
end
|
|
endmodule
|