mirror of
https://github.com/TomNisbet/TommyPROM.git
synced 2024-11-23 01:37:03 +00:00
62 lines
3.1 KiB
Markdown
62 lines
3.1 KiB
Markdown
---
|
||
title: 28C256 Notes
|
||
has_children: false
|
||
nav_order: 5
|
||
---
|
||
|
||
# Notes on 28C EEPROMs
|
||
|
||
The 28C series parallel EEPROMS, like the 28C256, support fast block writes and algorithms
|
||
to implement Software Data Protection (SDP). The SDP feature seems to be a leading cause
|
||
of problems for people trying to program these chips with Arduino or other homebrew
|
||
hardware.
|
||
|
||
The first problem many people encounter is that new chips are often locked, even though
|
||
the datasheet states that they should ship unlocked. It isn't clear if the manufacturing
|
||
practices have changed or if this might be due to used or counterfeit chips. In any case,
|
||
the chips may need to be unlocked before they can be programmed for the first time.
|
||
|
||
The unlock is accomplished by sending a sequence of bytes to specific addresses. Many
|
||
people have reported problems with this step when using DIY programmers. Some programmers
|
||
may not be writing the SDP sequences quickly enough to successfully unlock the chips and
|
||
yet others will report that the same hardware works correctly. This may be due to
|
||
variances in the behavior of chips from different manufacturers.
|
||
|
||
When writing SDP lock/unlock sequences, the datasheets note that the timing between bytes
|
||
must follow the same restrictions as page writes. In particular, the bytes must be
|
||
written within the tBLC (Byte Load Cycle time). On Atmel parts, this is specified as
|
||
150us max, so each write pulse must occur within 150us of the previous write. The tBLC
|
||
value is even shorter on the Xicor and ON Semi datasheets, stating that the writes must
|
||
occur within 100us of each other.
|
||
|
||
In practice, the Xicor chips seem very forgiving of the timing, doing successful SDP and
|
||
page write operations even when the tBLC is close to 200us. Atmel chips, on the other
|
||
hand, will refuse to unlock when the timing is outside the acceptable maximum.
|
||
|
||
# Solution
|
||
|
||
The TommyProm programmer uses direct port access on the Arduino to control the data bus
|
||
and addressing shift register. This is much faster than doing individual DigitalWrite
|
||
calls and allows the unlock and page write code to run comfortably within the tBLC
|
||
constraints. It has been successfully tested with the following 28C256 chips:
|
||
|
||
* Atmel AT28C256-15PU
|
||
* Catalyst/ON Semi CSI CAT28C256P-12
|
||
* Xicor X28C256P-15
|
||
* Xicor X28C256P-25
|
||
|
||
The Atmel chips tested included a batch from eBay that may not have been genuine, but they
|
||
were unlocked and burned successfully with the TommyProm code.
|
||
|
||
The capture below shows an unlock command sequence where the tBLC is within 80us for each
|
||
byte.
|
||
|
||
|
||
|
||
# References
|
||
|
||
1. [Atmel AT28C256 Data Sheet, 0006M–PEEPR–12/09](http://ww1.microchip.com/downloads/en/DeviceDoc/doc0006.pdf)
|
||
1. [Xicor, Intersil, Renesas X28C256 Data Sheet, 3855-1.9 8/1/97 T1/C0/D8 EW](https://www.renesas.com/us/en/www/doc/datasheet/x28hc256.pdf)
|
||
1. [ON Semiconductor CAT28C256 Data Sheet, CAT28C256/D, December, 2009 − Rev. 6](https://www.onsemi.com/pub/Collateral/CAT28C256-D.PDF)
|
||
1. [Parallel EEPROM Data Protection Application Note, Atmel, Rev. 0543C–10/98](http://ww1.microchip.com/downloads/en/AppNotes/DOC0543.PDF)
|