mirror of
https://github.com/TomNisbet/TommyPROM.git
synced 2024-12-21 03:29:21 +00:00
125 lines
6.5 KiB
Markdown
Executable File
125 lines
6.5 KiB
Markdown
Executable File
---
|
|
title: Overview
|
|
description: "TommyPROM Arduino based programmer for 28C256 EEPROMs"
|
|
has_children: false
|
|
nav_order: 1
|
|
---
|
|
|
|
# TommyPROM - An Arduino-based EEPROM programmer
|
|
|
|
This is a simple EEPROM programmer and reader that can be assembled using an Arduino and a
|
|
few additional parts. It has been successfully built using the Arduino UNO, Nano and
|
|
Boarduino models.
|
|
|
|
The original code was specific to the 28C256 32Kx8 EEPROM, but it has been extended to also support Intel 8755A EPROMS and some 29C010 Flash.
|
|
|
|
|
|
|
|
## Design
|
|
|
|
The 28C design can be used with other 5V EEPROMS as well. Many 5V chips, including UV
|
|
EPROMs, such as the 2716, 2764, 27C2001 and 27C040, can be read, but not written, with the
|
|
basic hardware. Some pin changes may be needed to get the signals to the correct pins on
|
|
the device. See the [Extending the design](extending) page for details on suggested
|
|
hardware and software changes needed to support new EPROM and EEPROM families.
|
|
|
|
The PROM-specific code is modular and can be easily adapted to support additional devices.
|
|
There are currently drivers and hardware designs for 28C series EEPROMS and the Intel
|
|
8755A EPROM.
|
|
|
|
Some 29C series chips, like the 29C010 can be written with the 28C hardware. The 29C
|
|
series only differs from the 28C in that the 29C chips erase and write an entire sector at
|
|
a time. The 29C010 and some 29C020 chips use a 128 byte sector, which matches the XModem
|
|
buffer in the current code. Other 29C020s and all 29C040s use a 256 byte sector and
|
|
cannot be written without code changes to buffer up an entire 256 byte block of data
|
|
before writing.
|
|
|
|
Features include:
|
|
* Simple hardware design that can be assembled on a breadboard.
|
|
* ROM images transfers using XMODEM - no special host client needed.
|
|
* Support for fast block EEPROM writes - a 32K EEPROM will program in just a few seconds.
|
|
* Optimized code that supports the timing requirements needed to unlock the 28C series Software Protection Algorithm.
|
|
* Modular software design to easily support other EEPROM and EPROM families.
|
|
|
|
The [hardware](hardware) page has descriptions of the hardware designs and links to schematics. The [software](software) page has class definitions and more information
|
|
on the software design.
|
|
|
|
The project was inspired by the
|
|
[MEEPROMMER programmer](http://www.ichbinzustaendig.de/dev/meeprommer-en).
|
|
|
|
## Compiling
|
|
|
|
Open the TommyPROM.ino file in the Arduino IDE. It should automatically open the cpp and h
|
|
files as well. The default code programs 28C series chips using Arduino Nano hardware. To
|
|
use this version, just compile and upload it to the Arduino.
|
|
|
|
**Note well** that this code has been optimized for the Aduino UNO and Nano hardware so
|
|
that it can run quickly enough to meet 28C series chip timing requirements for SDP
|
|
unlocking. To use different Arduino hardware, like the Micro, the board-specific code in
|
|
PromDevice.cpp and PromAddressDriver.cpp must be change to match the port mappings between
|
|
the ATmega chip and the Arduino I/O pins.
|
|
|
|
To use the 8755A version of the code and matching hardware, uncomment PROM_IS_8755A and
|
|
comment out the other PROM_IS_xx choices in Configure.h.
|
|
|
|
## Operation
|
|
|
|
|
|
To use the programmer, connect the Arduino USB to the host computer and run a terminal
|
|
program, such as TeraTerm (Windows) or Minicom (Linux). The Arduino development Serial
|
|
Monitor can also be used as a terminal initially, but it does not support XMODEM
|
|
transfers, so the READ and WRITE commands can't be used.
|
|
|
|
Disable both hardware and software flow control in the minicom settings for best results.
|
|
|
|
Set the terminal's serial parameters to 115200 baud, 8 bits, no parity, 1 stop bit to
|
|
match the Arduino. Press the Enter key. If the connection is successful, TommyPROM will
|
|
display a menu of options.
|
|
|
|
Most of the commands take a start address parameter, always entered as 1 to 5 hex
|
|
characters. Leading zeros are not required. If needed, the end address parameter is also
|
|
in hex. Parameters are separated by a space. For example, either of the commands:
|
|
|
|
d0000 01ff
|
|
d0 1ff
|
|
|
|
will dump memory from 0000H to 01ffH. Note that commands and parameters can be entered in
|
|
uppercase or lowercase.
|
|
|
|
The R command is used to read from a PROM and save a binary image on the host. The W
|
|
command receives a file from the host and writes (burns) it into the device. The R
|
|
command needs a start and end address. The W command determines the end address from the
|
|
received file size.
|
|
|
|
Once the READ or WRITE command is issued to the programmer, the transfer must
|
|
be started on the host program.
|
|
|
|
Note that previous versions of TommyPROM used the XMODEM-CRC protocol to complete the file
|
|
transfers for the READ and WRITE commands. This did not work well with minicom and other
|
|
Linux programs that rely on the sz/rz commands. Versions 2.5 and later of TommyPROM now
|
|
use basic XModem with the 8-bit checksum. The XModem-CRC support is still available as a
|
|
compile-time option. See [issue #19](https://github.com/TomNisbet/TommyPROM/issues/19)
|
|
for details.
|
|
|
|
The files used for READ and WRITE are simple binary images. This can be created directly
|
|
by [asm85](http://github.com/TomNisbet/asm85) or can be converted from S-record or Intel
|
|
HEX using an external utility.
|
|
|
|
## Troubleshooting
|
|
* Verify that the Arduino type you are using is a supported board or that its I/O port definitions match one of the supported boards. Some other Arduino boards, like the
|
|
Duemilanove, appear to be compatible but have not been tested. Others, like the Micro,
|
|
have different port mappings and definitely will not work without software changes.
|
|
* If the code doesn't appear to be working, concentrate on the read operations first to
|
|
verify that the data and address paths are good.
|
|
* 28C series EEPROMS, like the X28C256, sometimes ship from the factory with Data
|
|
Protection enabled. Use the UNLOCK command to disable this. See the
|
|
[28C256 Notes](28C256-notes) for more information.
|
|
* Re-check all hardware connections and verify the the control pins are going to the
|
|
Arduino pins that match the definitions in the code.
|
|
* This repo contains a standalone program called HardwareVerify that allows low-level
|
|
access to the address, data, and control lines through a menu-driven interface. See the [troubleshooting](troubleshooting) section for more tips.
|
|
|
|
## Further Work
|
|
* [ ]Add a new PromDevice class for 27 series EPROMS.
|
|
* [x] Additional error checking in the CmdLine code.
|