mirror of
https://github.com/TomNisbet/TommyPROM.git
synced 2024-11-28 03:51:09 +00:00
84 lines
4.1 KiB
Markdown
84 lines
4.1 KiB
Markdown
---
|
|
title: "Software Design"
|
|
permalink: /docs/software
|
|
exerpt: "TommyPROM Arduino EEPROM programmer software design"
|
|
---
|
|
|
|
The software is designed around several major blocks and classes. The code has been
|
|
broken out into individual files to make it easy to extend the hardware support to
|
|
additional EPROM and EEPROM families. See the
|
|
[Adding Chip Families](extending) page for details on suggested hardware and software
|
|
changes needed.
|
|
|
|
## CommandStatus class
|
|
|
|
The CommandStatus class stores the execution status of the previous command. It allows
|
|
the status to be saved (and recalled using the / command) instead of just printing the
|
|
status at the completion of the command. This was important for debugging XMODEM
|
|
problems, because the error messages would get eaten as part of the transfer. The class
|
|
has utility beyond XMODEM because it includes formatting that relieves each command from
|
|
having to build parameterized error messages with multiple print calls.
|
|
|
|
## Xmodem class
|
|
|
|
The Xmodem class implements the communications protocols needed to do XMODEM or XMODEM-CRC
|
|
transmit and receive. It calls directly into the PROM read and write code, so the
|
|
complete files are never stored during the transfer.
|
|
|
|
## CLI code and command implementation
|
|
|
|
This code parses input commands and parameters and executes the commands.
|
|
|
|
A compile-time switch in Configure.h enables additional debug commands that are not needed
|
|
in normal operation, but are very useful to verify proper operation of the hardware.
|
|
|
|
## PromDevice class
|
|
|
|
The PromDevice class and its subclasses encapsulate all of the communication between the
|
|
Arduino and the target PROM device.
|
|
|
|
To meet the timing requirements for block writes and 28C chip unlocking, the PromDevice
|
|
class accesses the shift registers and data bus using direct port writes instead of 8
|
|
individual pin accesses. This greatly increases performance, but it makes the code
|
|
dependent on the particular flavor of Arduino being used. The code supports the Uno,
|
|
Nano, and Boarduino versions of Arduino hardware or any other variant that uses that same
|
|
mapping of ATMega ports to I/O pins. To support a different Arduino board, either change
|
|
the pins used to match the mapping in the software, or change the hardware-specific code
|
|
in PromDevice.cpp and PromAddressDriver.cpp.
|
|
|
|
The PromDevice class contains common code used by all devices, including the block write
|
|
code that will break a large write request into a set of properly-aligned smaller blocks
|
|
for devices that support block writing, or a sequence of individual byte writes for
|
|
devices that do not.
|
|
|
|
Subclasses of the PromDevice class provide the device-specific code. To accommodate the
|
|
limited memory footprint of the Arduino, only a single subclass will be compiled into the
|
|
final code. This is controlled via switches in the Configure.h file.
|
|
|
|
The device-specific subclasses are described below. Each class provides pin definitions,
|
|
byte read, byte burn, and optional block burn code that is specific to the timing of the
|
|
chip. They also supply a SetAddress method that either calls the built-in code for the
|
|
shift register hardware or provides device-specific address code.
|
|
|
|
### PromDevice28C class
|
|
|
|
Although the existing code is specific to the 28C256, the constructor has parameters that
|
|
easily support other chips. The current design has been used to read other chips,
|
|
including 2764 and 29c040 EPROMs.
|
|
|
|
The 28C code supports fast block writes, allowing a 32K byte chip to be programmed in just
|
|
a few seconds.
|
|
|
|
### PromDevice8755A class
|
|
|
|
The PromDevice8755A class provides the byte read and byte write code, as well as
|
|
SetAddress code that accommodates the ALE used on this chip. The byte write code controls
|
|
the Vdd switching hardware that toggles the Vdd pin between the normal 5V value and the
|
|
25V programming pulse.
|
|
|
|
### PromAddressDriver class
|
|
|
|
Although not actually a subclass of PromDevice, this contains the code to drive the shift
|
|
registers that provide the address lines. If this hardware is used, the PromDeviceXX class
|
|
can call this code to implement the SetAddress methods.
|