mirror of
https://github.com/TomNisbet/TommyPROM.git
synced 2024-11-23 01:37:03 +00:00
92 lines
5.1 KiB
Markdown
Executable File
92 lines
5.1 KiB
Markdown
Executable File
---
|
|
title: "TommyPROM - An Arduino-based EEPROM programmer"
|
|
permalink: /
|
|
excerpt: "TommyPROM Arduino based programmer for 28C256 EEPROMs"
|
|
---
|
|
|
|
TommyPROM is a simple EEPROM programmer and reader that can be assembled using an Arduino and a
|
|
few additional parts. It has been successfully built using the Arduino UNO, Nano and
|
|
Boarduino models.
|
|
|
|
The original code was specific to the 28C256 32Kx8 EEPROM, but it has been extended to
|
|
also support SST39SF flash, 27C EPROMs, 29C flash and the Intel 8755A EPROMS.
|
|
|
|
[](docs/images/TommyPROM-nano.jpg)
|
|
|
|
Features include:
|
|
* Simple hardware design that can be assembled on a breadboard.
|
|
* ROM images transfers using XMODEM - no special host client needed.
|
|
* Support for fast block EEPROM writes - a 32K EEPROM will program in just a few seconds.
|
|
* Optimized code that supports the timing requirements needed to unlock the 28C series [Software Data Protection](docs/28C256-notes) Algorithm.
|
|
* Modular software design to easily support other EEPROM, flash, and EPROM families.
|
|
* Hardware support for 19 address lines, allowing the use of chips as large as 512KB, like the SST39SF040 and 29C040.
|
|
|
|
## Design
|
|
|
|
The 28C hardware and software design can be used with other 5V PROMS as well. Many 5V
|
|
chips, including UV EPROMs such as the 2716, 2764, 27C2001 and 27C040, can be read, but
|
|
not written, with the basic hardware. Some pin changes may be needed to get the signals to
|
|
the correct pins on the device. See the [Extending the design](docs/extending) page for
|
|
details on suggested hardware and software changes needed to support new
|
|
[EPROM, flash,and EEPROM families](docs/prom-families).
|
|
|
|
The PROM-specific code is modular and can be easily adapted to support additional devices.
|
|
There are currently drivers for 28C series EEPROMS, SST39SF flash, 27C EPROMs and the
|
|
Intel 8755A EPROM.
|
|
|
|
Some 29C series chips, like the 29C010 can be written with the 28C hardware and driver.
|
|
The 29C series only differs from the 28C in that the 29C chips erase and write an entire
|
|
sector at a time. The 29C010 and some 29C020 chips use a 128 byte sector, which matches
|
|
the XModem buffer in the current code. Other 29C020s and all 29C040s use a 256 byte
|
|
sector and cannot be written without code changes to buffer up an entire 256 byte block of
|
|
data before writing.
|
|
|
|
The [hardware](docs/hardware) page has descriptions of the hardware designs and links to
|
|
schematics. The [software](docs/software) page has class definitions and more information on
|
|
the software design.
|
|
|
|
The project was inspired by the
|
|
[MEEPROMMER programmer](https://github.com/mkeller0815/MEEPROMMER).
|
|
|
|
## PCB Version
|
|
|
|
Although it was originally designed as a one-off programmer to be used on a breadboard,
|
|
there are now some PCB versions as well. The [PCB](docs/pcb) page has descriptions with links
|
|
to the KiCad schematics and Gerber files.
|
|
|
|
[](docs/images/TommyPROM-pcb.jpg)
|
|
|
|
## Compiling
|
|
|
|
Open the TommyPROM.ino file in the Arduino IDE. It should automatically open the cpp and h
|
|
files as well. The default code programs 28C series chips using Arduino Nano hardware. To
|
|
use this version, just compile and upload it to the Arduino.
|
|
|
|
**Note well** that this code has been optimized for the Aduino UNO and Nano hardware so
|
|
that it can run quickly enough to meet 28C series chip timing requirements for SDP
|
|
unlocking. To use different Arduino hardware, like the Micro, the board-specific code in
|
|
PromDevice.cpp and PromAddressDriver.cpp must be changed to match the port mappings
|
|
between the ATmega chip and the Arduino I/O pins.
|
|
|
|
Because the Arduino has limited code and RAM space available, only one PROM driver is
|
|
compiled in at a time. To change drivers, uncomment the desired PROM_IS_xx line in
|
|
Configure.h and comment out the other choices. The code to instantiate the driver is
|
|
near the top in TommyPROM.ino. The change to Configure.h will automatically cause a
|
|
driver to be installed, but it may be necessary to modify the parameters for a specific
|
|
chip type.
|
|
|
|
## Troubleshooting
|
|
|
|
* Verify that the Arduino type you are using is a supported board or that its I/O port definitions match one of the supported boards. Some other Arduino boards, like the
|
|
Duemilanove, appear to be compatible but have not been tested. Others, like the Micro,
|
|
have different port mappings and definitely will not work without software changes.
|
|
* If the code doesn't appear to be working, concentrate on the read operations first to
|
|
verify that the data and address paths are good.
|
|
* 28C series EEPROMS, like the X28C256, sometimes ship from the factory with Data
|
|
Protection enabled. Use the UNLOCK command to disable this. See the
|
|
[28C256 Notes](docs/28C256-notes) for more information.
|
|
* Re-check all hardware connections and verify the the control pins are going to the
|
|
Arduino pins that match the definitions in the code.
|
|
* This repo contains a standalone program called HardwareVerify that allows low-level
|
|
access to the address, data, and control lines through a menu-driven interface. See the [troubleshooting](docs/troubleshooting) section for more tips.
|