mirror of
https://github.com/TomNisbet/TommyPROM.git
synced 2024-11-22 10:31:39 +00:00
71 lines
3.6 KiB
Markdown
71 lines
3.6 KiB
Markdown
---
|
|
title: Printed Circuit Boards
|
|
permalink: /docs/pcb
|
|
exerpt: "Printed Circuit Boards"
|
|
---
|
|
|
|
Although it was originally designed as a one-off programmer to be used on a breadboard,
|
|
there are now some PCB versions.
|
|
|
|
## 28C256 PCB
|
|
|
|
A PCB version for the 28C256 and 28C64 chips was built to support a SAP-1 TTL breadboard
|
|
computer. This project required a lot of burns for its microcode and the PCB version
|
|
with the ZIF socket was much quicker than prying the chips out of a breadboard without
|
|
disturbing any of the wires.
|
|
|
|
The [KiCad design files](https://github.com/TomNisbet/TommyPROM/tree/master/schematics)
|
|
are in the project repo.
|
|
|
|
[![TommyPROM PCB](images/TommyPROM-pcb-with-microcode-500.jpg)](images/TommyPROM-pcb.jpg)
|
|
|
|
## TommyPROM32
|
|
|
|
TommyPROM32 was built to support SST39SF0x0 and other 32-pin EEPROM and Flash chips. While
|
|
providing a stable platform for the SST39SF chips, the board can serve as a test bed for
|
|
other chips as well. It uses a set of headers that allow any of the signals to the target
|
|
chip to be re-routed. The default configuration, with just jumper shunts installed, is
|
|
wired for the SST39SF0x0 chips.
|
|
|
|
[![TommyPROM PCB](images/TommyPROM32-SST39SF-500.jpg)](images/TommyPROM32-SST39SF.jpg)
|
|
|
|
Many other chips, particularly if they follow JEDEC standards, can be supported by
|
|
removing shunts and adding just a few jumper wires.
|
|
|
|
Chips with fewer pins can also be supported. There are power pins in place to support
|
|
28-pin and 24-pin chips with a shunt to the correct VCC pin. The photo below shows the
|
|
28C256 with a power jumper on pin 28, the _WE_ signal moved down to pin 27, and the _A14_
|
|
signal moved from ping 27 to pin 1.
|
|
|
|
[![TommyPROM PCB](images/TommyPROM32-28C256-500.jpg)](images/TommyPROM32-28C256.jpg)
|
|
|
|
Power inputs and a switch are provided to support older flash and EEPROM chips that need
|
|
higher programming voltages. Many of these chips just need a higher voltage, like 12V,
|
|
applied to the VPP pin continuously during the programing and verification cycle. In
|
|
normal operation, the 5V VCC signal is applied to the VPP pin. The board has VPP inputs
|
|
for two voltages. Applying 12V to _VPP In High_ and 5V to _VPP In Low_ lets the VPP
|
|
output be switched between these two voltages using a manual slide switch for programming.
|
|
|
|
The photo below shows the WE27C257 set up for programming. The _VPP in Low_ signal is
|
|
connected to _VCC_ and the _VPP in High_ signal is using 12V from an external power
|
|
supply. The _VPP Out_ signal is connected to the chip's VPP on pin 1. The chip is in
|
|
programming mode when the slide switch is set to the _High_ position and is in read mode
|
|
when in the _Low_ position.
|
|
|
|
[![TommyPROM PCB](images/TommyPROM32-27C257-pgm-500.jpg)](images/TommyPROM32-27C257-pgm.jpg)
|
|
|
|
To erase the WE27C257 chip, the external power supply is providing 14V and the _VPP Out_
|
|
is connected to the chip's _VPP_ and _A9_ pins. An external breadboard was needed to
|
|
allow the _VPP Out_ signal to be connected to multiple pins. A new spin of the board is
|
|
planned with multiple _VPP Output_ pins and some general-purpose interconnect pins.
|
|
|
|
[![TommyPROM PCB](images/TommyPROM32-27C257-erase-500.jpg)](images/TommyPROM32-27C257-erase.jpg)
|
|
|
|
For chips that require a high voltage VPP pulse during programming, some external
|
|
switching circuitry will be needed to allow the Arduino to control the VPP voltage. There
|
|
is a header connected to the unused D13 pin that can support this. See the
|
|
[Intel 8755 version of the hardware](hardware/#intel-8755a-hardware-version) for an
|
|
example of voltage switching by TommyPROM.
|
|
|
|
[![TommyPROM PCB](images/TommyPROM32-sch-700.png)](images/TommyPROM32-sch.png)
|