Apple-2-HW/micro-sci-a2-controller
1
0
Fork 0
mirror of https://codeberg.org/cryu/micro-sci-a2-controller synced 2024-12-21 12:29:29 +00:00
Code Issues Packages Projects Releases Wiki Activity
70 Commits 4 Branches 2 Tags 54 MiB
Assembly 91%
C 5.6%
Makefile 3.4%
main
Go to file
Christopher RYU 9cf7d60e07 Syntax and brevity
2023-08-22 18:34:14 +09:00
apple2-bus.pretty Initial commit. 2023-07-10 05:40:39 +09:00
doc Add original user documentation. 2023-07-26 10:22:07 +09:00
firmware Syntax and brevity 2023-08-22 18:34:14 +09:00
.gitignore Nuke erroneously added files. 2023-07-29 06:35:24 +09:00
apple2.kicad_sym Initial commit. 2023-07-10 05:40:39 +09:00
eprom.kicad_sym Switch to 2716/2732. 2023-07-16 11:48:36 +09:00
fp-lib-table Initial commit. 2023-07-10 05:40:39 +09:00
LICENSE Initial commit 2023-07-09 20:35:18 +00:00
MicroSci Floppy Controller.kicad_pcb Add pull-up resistors where appropriate. 2023-07-30 19:53:06 +09:00
MicroSci Floppy Controller.kicad_pro Add pull-up resistors where appropriate. 2023-07-30 19:53:06 +09:00
MicroSci Floppy Controller.kicad_sch Add pull-up resistors where appropriate. 2023-07-30 19:53:06 +09:00
README.md Revise DIP switch documentation. 2023-07-30 05:38:22 +09:00
sym-lib-table Switch to 2716/2732. 2023-07-16 11:48:36 +09:00
TTL.kicad_sym Initial commit. 2023-07-10 05:40:39 +09:00
usci.png Re-render. 2023-08-08 17:29:15 +09:00

README.md

Micro-SCI / Franklin Apple ][ Floppy Drive Controller

This is a clone of the Micro-SCI / Franklin floppy drive controller.

v0.1 is a direct clone, reverse-engineered from a Micro-SCI board. It was cross-checked with a Franklin-branded board, as well as the (belatedly discovered) official Franklin schematic (included in doc/service_and_schematics.pdf)

v0.2 has the following enhancements over the original design:

  • the 2708 EPROM has been replaced with a more-common 2716/2732 EPROM
  • decoupling capacitors have been added
  • footprints for all capacitors and resistors have been modernized
  • firmware EPROM bank selection jumpers replaced with a DIP switch
  • obsolete MPS-U51 transistor replaced with modern equivalent
  • clearly-marked calibration test points have been added
  • ground pours used to increase operational stability
  • support for using Floppy Emu in dual-drive emulation mode with one cable

Firmware images can be built via the Makefile in the firmware subdirectory. The build framework requires cc65.

usci

EPROM bank select switches (J4)

  • 1:off 2:off - firmware "put jumpers here" splash screen (0x0300)
  • 1:off 2: on - 13-sector firmware (0x0200)
  • 1: on 2:off - 16-sector firmware (0x0100)
  • 1: on 2: on - controller test firmware (0x0000)

Calibration procedure

  • set J4 to on/on ("controller test firmware")
  • connect oscilloscope to TP1
  • start machine
  • execute "call 50688"
  • execute "AAW" (and immediately hit ESC)
  • adjust R1 until waveform period is 5.4 microseconds
  • connect oscilloscope to TP2
  • execute "99W" (and immediately hit ESX)
  • adjust R2 until waveform period is 3.8 microseconds
  • card is now calibrated, power off machine and set J4 to "16-sector firmware"

Construction notes

  • J3 can be omitted if this controller is used with a FloppyEmu
  • All discrete logic ICs (except U15, the 74LS373) can be CMOS (74ACT, 74HCT). As is unfortunately usual with the Apple ][, U15 must be LS due to timing issues.
  • if CMOS logic is used, then Q1/R6/R7 can be omitted -- the entire logic array can remain powered up at all times. Connect pads 1 and 3 on the Q1 footprint.