mirror of
https://github.com/osiweb/unified_retro_keyboard.git
synced 2024-11-22 04:33:19 +00:00
68 lines
3.2 KiB
Markdown
68 lines
3.2 KiB
Markdown
# Apple II/II+ Encoder
|
|
|
|
This is a version of the ASCII interface wired up to be compatible with the
|
|
Apple II/Apple II+ keyboard matrix. This board was broken out as a separate PCB
|
|
from the Atmega2560-based interface board on which it was based, in order to
|
|
keep the "custom" connector customizable on that board.
|
|
|
|
This board is otherwise identical to rev 3.4 of the ATMega2560-based ASCII interface board, and shares the same firmware and features.
|
|
|
|
<img alt="Assembly Rendering" src="images/PCB-assembly-rendering.png" height=75%
|
|
width=75%>
|
|
|
|
## Features
|
|
- Parallel or serial output
|
|
- Up to 8 configuration settings via an up-to-8 position DIP switch
|
|
- Apple 1, Apple 2, and SOL-20 compatible outputs. Other configurations can be
|
|
supported by making a custom cable.
|
|
- Can decode arbitrary keyboards up 16 rows by 8 columns.
|
|
- Supports up to 3 keyboard LEDs
|
|
- Supports up to 3 "special" host outputs, such as RESET, SCREEN_CLEAR, BREAK, etc.
|
|
- Socket for custom connector
|
|
|
|
## Assembly Notes
|
|
|
|
- You may build this board as if it is a general purpose ASCII interface. In
|
|
that case, you may want to avoid installing the 1x25 Apple2 keyboard header
|
|
if it interferes with the target keyboard matrix.
|
|
|
|
- This encoder is normally used with keyboards that have a diode per key. For use
|
|
with a key matrix with no diodes (such as the Apple 2 key matrix), cut the PCB
|
|
traces that short diodes D1-16, and install D1-16.
|
|
|
|
|
|
- If you ARE building this board as an Apple 2 encoder, then you may OMIT:
|
|
|
|
- Sol-20 connector J5
|
|
- Custom connector J7
|
|
- D17,D18,D19 - These are used for the "classic" keyboard matrix.
|
|
- D7,D8,D15,D16 - These are diodes for rows 12-15, which are not used.
|
|
- The serial out connector J3 if you do not plan to use a serial output.
|
|
- The I/O connector J4, as all the I/O lines are routed through the
|
|
keyboard connector.
|
|
- If you will be using the keyboard with only an Apple 1 or Apple 2, then
|
|
you do not need to install both the Apple 2 connector (J1) AND the Apple
|
|
1 connector (J2). You may install only the one you plan to use, and
|
|
reduce the risk of plugging into the wrong socket (and possibly damaging
|
|
the encoder).
|
|
|
|
1. Solder the surface-mount microcontroller first. Be sure to match pin 1 to the
|
|
dot on the silk-screen layer.
|
|
1. Next, install the surface mount crystal, Y1. The orientation is not important.
|
|
1. Next, solder in the resitor R1
|
|
1. Install all the capacitors. Be sure to separate out the two capacitors for the XTAL
|
|
circuit from the other capacitors, the rest of which are 0.1uF bypass capacitors.
|
|
1. Install the In-circuit Serial Programming (ISP) header, J6. (right-angle, 2x3
|
|
0.100")
|
|
1. If you will be using the Apple 1 connector, install the DIP socket J1 (16-pin
|
|
dip). If you plan to insert and remove the cable many times, a dual-wipe
|
|
socket may be preferable to machine-pin, since it has a lower insertion
|
|
force, and you will be less likely to bend pins. If you plan to insert the
|
|
cable once and leave it forever, I suggest a machine-pin DIP socket.
|
|
1. If you will be using the Apple 2 connector, install the DIP socket J2 (16-pin
|
|
dip). The note for the Apple 1 connector selection applies here as well.
|
|
|
|
|
|
|
|
|