mirror of
https://github.com/oliverschmidt/contiki.git
synced 2024-08-15 00:29:02 +00:00
184 lines
7.7 KiB
Markdown
184 lines
7.7 KiB
Markdown
Getting Started with Contiki for TI CC26xx
|
|
==========================================
|
|
|
|
This guide's aim is to help you start using Contiki for TI's CC26xx. The
|
|
platform supports two different boards:
|
|
|
|
* SmartRF 06 Evaluation Board with a CC26xx Evaluation Module (relevant files
|
|
and drivers are under `srf06/`)
|
|
* CC26xx SensorTag 2.0 (relevant drivers under `sensortag/`)
|
|
|
|
The CPU code, common for both platforms, can be found under `$(CONTIKI)/cpu/cc26xx`.
|
|
The port was developed and tested with CC2650s, but the intention is for it to
|
|
work with the CC2630 as well. Thus, bug reports are welcome for both chips.
|
|
Bear in mind that the CC2630 does not have BLE capability.
|
|
|
|
This port is only meant to work with 7x7mm chips
|
|
|
|
This guide assumes that you have basic understanding of how to use the command
|
|
line and perform basic admin tasks on UNIX family OSs.
|
|
|
|
Port Features
|
|
=============
|
|
The platform has the following key features:
|
|
|
|
* Deep Sleep support with RAM retention for ultra-low energy consumption.
|
|
* Support for CC26xx RF in IEEE as well as BLE mode (BLE support is very basic
|
|
since Contiki does not provide a BLE stack).
|
|
|
|
In terms of hardware support, the following drivers have been implemented:
|
|
|
|
* SmartRF06 EB peripherals
|
|
* LEDs
|
|
* Buttons
|
|
* UART connectivity over the XDS100v3 backchannel
|
|
* SensorTag 2.0
|
|
* LEDs
|
|
* Buttons (One of the buttons can be used as a shutdown button)
|
|
* Reed relay
|
|
* Motion Processing Unit (MPU9250 - Accelerometer, Gyro)
|
|
* BMP280 sensor
|
|
* TMP007 sensor
|
|
* HDC1000 sensor
|
|
* OPT3001 sensor
|
|
* Buzzer
|
|
* External SPI flash
|
|
|
|
Examples
|
|
========
|
|
The port comes with two examples: A very basic example and a mode advanced one
|
|
(web demo). The former demonstrates how to read sensors and how to use board
|
|
peripherals. It also demonstrates how to send out BLE advertisements.
|
|
The latter includes a CoAP server, an MQTT client which connects and publishes
|
|
to the IBM quickstart service, a net-based UART and lastly a web server that
|
|
can be used to configure the rest of the example.
|
|
|
|
More details about those two examples can be found in their respective READMEs.
|
|
|
|
Requirements
|
|
============
|
|
To use the port you need:
|
|
|
|
* TI's CC26xxware sources (more below)
|
|
* Software to program the nodes. Use TI's SmartRF Flash Programmer
|
|
* A toolchain to build firmware: The port has been developed and tested with
|
|
GNU Tools for ARM Embedded Processors <https://launchpad.net/gcc-arm-embedded>.
|
|
The port was developed and tested using this version:
|
|
|
|
$ arm-none-eabi-gcc -v
|
|
[...]
|
|
gcc version 4.9.3 20141119 (release) [ARM/embedded-4_9-branch revision 218278] (GNU Tools for ARM Embedded Processors)
|
|
|
|
* You may also need other drivers so that the SmartRF can communicate with your
|
|
operating system and so that you can use the chip's UART for I/O. Please read
|
|
the section ["Drivers" in the CC2538DK readme](https://github.com/contiki-os/contiki/tree/master/platform/cc2538dk#drivers).
|
|
|
|
Environment
|
|
===========
|
|
To use this port, you will need to download and extract CC26xxware sources. We
|
|
currently use CC26xxware version 2.20.06.14829. The download link can be found
|
|
here: http://processors.wiki.ti.com/index.php/CC26xxware
|
|
|
|
Once you have done this, you will need to configure the Contiki build system so
|
|
that it can locate and compile them as part of the build process.
|
|
|
|
To do this, you will need to set the following environment variable:
|
|
|
|
* `TI_CC26XXWARE`
|
|
|
|
Stores the path to a directory containing the following:
|
|
|
|
* cc26xxware sources under `$(TI_CC26XXWARE)/driverlib`
|
|
* cc26xxware includes under `$(TI_CC26XXWARE)/inc`
|
|
* Startup files under `$(TI_CC26XXWARE)/startup_files`
|
|
|
|
This _must_ be a path relative to the Contiki source directory. For
|
|
example, if Contiki is in `/home/user/contiki-2.x` and the CC26xxware is in
|
|
`/home/user/cc26xxware`, then `TI_CC26XXWARE` must be set to `../cc26xxware`
|
|
|
|
The variable can be set within the example's Makefile, by adding this:
|
|
|
|
TI_CC26XXWARE=../cc26xxware
|
|
|
|
or you can use an environment variable, like so:
|
|
|
|
export TI_CC26XXWARE=../cc26xxware
|
|
|
|
Filename conflicts between Contiki and CC26xxware
|
|
=================================================
|
|
There is a file called `timer.c` both in Contiki as well as in CC26xxware. The
|
|
way things are configured now, we don't use the latter. However, if you need to
|
|
start using it at some point, you will need to rename it:
|
|
|
|
From `$(TI_CC26XXWARE)/driverlib/cc26xx/source/timer.c` to `driverlib-timer.c`
|
|
|
|
Sensortag vs Srf06
|
|
==================
|
|
To build for the sensortag, set `BOARD=sensortag`. You can do that by exporting
|
|
it as an environment variable, by adding it to your Makefile or by adding it to
|
|
your make command as an argument
|
|
|
|
If the `BOARD` variable is not equal to `sensortag`, an image for the Srf06
|
|
CC26XXEM will be built instead.
|
|
|
|
If you want to switch between building for one platform to the other, make
|
|
certain to `make clean` before building for the new one, or you will get linker
|
|
errors.
|
|
|
|
Low Power Operation
|
|
===================
|
|
The platform takes advantage of the CC26xx's power saving features. In a
|
|
nutshell, here is how things work:
|
|
|
|
* When the RF is TXing, the CPU will enter sleep mode and will resume after TX
|
|
has completed.
|
|
* When there are no events in the Contiki event queue, the chip will enter
|
|
'some' low power mode (more below).
|
|
|
|
We do not use pre-defined power profiles (e.g. as mentioned in the TRM or as
|
|
we do for the CC2538 with LPM1, LPM2 etc). Each time we enter low power
|
|
operation, we either put the CM3 to sleep or to deep sleep. The latter case is
|
|
highly configurable: the LPM engine allows other code modules to register
|
|
themselves for notifications and to configure low power operation. With these
|
|
facilities, a module can e.g. prohibit deep sleep altogether, or it can request
|
|
that a power domain be kept powered. The LPM engine will turn off as many
|
|
CC26xx components as it can while satisfying all restrictions set by registered
|
|
modules.
|
|
|
|
To determine which power mode to use, the following logic is followed:
|
|
|
|
* The deepest available low power mode can be hard-coded by using
|
|
the `LPM_MODE_MAX_SUPPORTED` macro in the LPM driver (`lpm.[ch]`). Thus, it
|
|
is possible to prohibit deep sleep altogether.
|
|
* Code modules which are affected by low power operation can 'register'
|
|
themselves with the LPM driver.
|
|
* If the projected low-power duration is lower than `STANDBY_MIN_DURATION`,
|
|
the chip will simply sleep.
|
|
* If the projected low power duration is sufficiently long, the LPM will visit
|
|
all registered modules to query the maximum allowed power mode (maximum means
|
|
sleep vs deep sleep in this context). It will then drop to this power mode.
|
|
This is where a code module can forbid deep sleep if required.
|
|
* All registered modules will be notified when the chip is about to enter
|
|
deep sleep, as well as after wake-up.
|
|
|
|
When the chip does enter deep sleep:
|
|
|
|
* The RF Core, VIMS, SYSBUS and CPU power domains are always turned off. Due to
|
|
the way the RF driver works, the RFCORE PD should be off already.
|
|
* Peripheral clocks stop
|
|
* The Serial and Peripheral power domains are turned off, unless an LPM module
|
|
requests them to stay operational. For example, the net-uart demo keeps the
|
|
serial power domain powered on and the UART clocked under sleep and deep
|
|
sleep in order to retain UART RX functionality.
|
|
* If both SERIAL and PERIPH PDs are turned off, we also switch power source to
|
|
the uLDO for ultra low leakage under deep sleep.
|
|
|
|
The chip will come out of low power mode by one of the following events:
|
|
|
|
* Button press or, in the case of the SensorTag, a reed relay trigger
|
|
* Software clock tick (timer). The clock ticks at 128Hz, therefore the maximum
|
|
time we will ever spend in a sleep mode is 7.8125ms. In hardware terms, this
|
|
is an AON RTC Channel 2 compare interrupt.
|
|
* Rtimer triggers, as part of ContikiMAC's sleep/wake-up cycles. The rtimer
|
|
sits on the AON RTC channel 0.
|