mirror of
https://github.com/oliverschmidt/contiki.git
synced 2024-12-23 01:29:33 +00:00
29914b5a1f
For avr-rss2 platform
168 lines
5.4 KiB
Markdown
168 lines
5.4 KiB
Markdown
Getting Started with Contiki using avr-rss2
|
|
===========================================
|
|
This guide's aim is to help you start using Contiki for RSS2 boards
|
|
The platform supports different AtMega-RF boards:
|
|
|
|
* Based on MCU AtMega128RFR2
|
|
* Based on MCU AtMega256RFR2
|
|
* Based on MCU AtMega128RFA1
|
|
|
|
Boards all looks the same. AtMega256RFR2 boards are labeled with "Made in EU".
|
|
The platform and CPU code, are common for both boards, can be found under
|
|
`$(CONTIKI)/platfrom/avr-rssa`. The port was developed and tested with RSS2.
|
|
This guide assumes that you have basic understanding of how to use the
|
|
command line and perform basic admin tasks on UNIX family OSs. You should
|
|
also have understanding about the Contiki OS design as well have C
|
|
programming skills.
|
|
|
|
Board Features
|
|
----------------
|
|
* Chip Antenna. Supercardiod.
|
|
* Robust radio performance. Up to 300 meter line-of-sight.
|
|
* Unique EUI64 address via chip combined with EEPROM
|
|
* Onboard temp sensor DS18B20,
|
|
* Light Sensor.
|
|
* 32kHz RTC xtal
|
|
* Comparator chip and input.
|
|
* SW FET, (relay) for power on/off of sensors.
|
|
* DC input via LDO up to 25V.
|
|
* Standard. 6-pin TTL-USB header for FTDI cable for UART.
|
|
* PCB formfactor for cheap project box G.40X IP54
|
|
* Power/current:
|
|
* RX ~10mA (Full RPC AtMegaXXRFR2).
|
|
* Sleep ~45uA @ 16MHz XTAL
|
|
* Sleep ~15uA @ 8MHz using internal oscillator
|
|
* Preprogammed bootloader.
|
|
* CE certified by test institute.
|
|
|
|
UART
|
|
----
|
|
The board has one UART via the 6-pin TTL-USB adapter, The recommended
|
|
baudrate is 38400 bps. This speed gives the lowest error with respect
|
|
of the used clock frequency used internally. A possible hi-speed is
|
|
250000 bps wich gives 0% Error with 16MHz clock.
|
|
|
|
Port Features
|
|
--------------
|
|
The platform has the following key features:
|
|
* Standard, E64 address from built-in chip.
|
|
* First hooks for RPC (Reduced Power Consumption) for AtMegaXXXRFR2.
|
|
|
|
Toolchain needs
|
|
---------------
|
|
The Atmel toolcahin is available in most operating system.
|
|
Note. The native OS packages does not yet support the new
|
|
AtMega256RfR2 MCU.
|
|
|
|
We'll use toolchain from Atmels web-site. You might also consider
|
|
Instant Contiki.
|
|
|
|
|
|
###### For Linux
|
|
|
|
1. See http://www.atmel.com/tools/ATMELAVRTOOLCHAINFORLINUX.aspx
|
|
2. Download the proper 8-bit platform 32 or 64 bit.
|
|
3. Unpack under `/usr/local`
|
|
4. Add to your search PATH. For example add to `.bashrc`: `export PATH=$PATH:/usr/local/avr8-gnu-toolchain-linux_x86_64/bin` (for 64 bit systems) or `export PATH=$PATH:/usr/local/avr8-gnu-toolchain-linux_x86/bin` (for 32 birt systems).
|
|
5. For flash programming you'll need `avrdude`. It can be installed with the command
|
|
`apt-get install avrdude`
|
|
|
|
###### For Windows
|
|
|
|
Goes here
|
|
|
|
Contiki build TARGET
|
|
--------------------
|
|
make TARGET=avr-rss2
|
|
|
|
For AtMega128RFR2 boards:
|
|
|
|
make TARGET=avr-rss2 MCU=atmega128rfr2
|
|
|
|
For AtMega128RFA1 boards:
|
|
|
|
make TARGET=avr-rss2 MCU=atmega128rfa1
|
|
|
|
Flashing
|
|
--------
|
|
Programming using avrdude using serial bootloader. (TTL-USB cable)
|
|
Press the RESET button. The bootloader with wait for boot commands
|
|
for 3 seconds.
|
|
|
|
Flashing commnad line example 256k MCU:
|
|
|
|
avrdude -p m256rfr2 -c stk500v2 -P /dev/ttyUSB0 -b 38400 -e -U flash:w:hello-world.avr-rss2
|
|
|
|
Flashing commnad line example 128k MCU:
|
|
|
|
avrdude -p m128rfa1 -c avr109 -P /dev/ttyUSB0 -b 38400 -e -U flash:w:hello-world.avr-rss2
|
|
|
|
Older boards may use the avr109 boot loader. The `stk500v2` uses the yellow
|
|
lED while the avr109 uses the red LED.
|
|
|
|
Tested applications and examples
|
|
---------------------------------
|
|
* `hello-world`
|
|
* `ipv6/rpl-udp`
|
|
* `ipv6/simple-udp-rpl`
|
|
* `rime`
|
|
* `ipv6/multicast`
|
|
* `examples/powertrace`
|
|
* `example-shell`
|
|
|
|
Platform tutorial applications
|
|
-----------------------------
|
|
Example to read out various sensors, leds, serial numbers, and so on:
|
|
[platform/avr-rss2/examples/hello-sensors/](examples/hello-sensors/).
|
|
|
|
The previous example uses the `sensd` data encoding. An example that uses UDP through 6lowpan is here:
|
|
[platform/avr-rss2/examples/ipv6/rpl-udp-report](examples/ipv6/rpl-udp-report).
|
|
|
|
An Ethernet gateway with ip64 NAT, based on Contiki `core/net/ip64` code:
|
|
[platform/avr-rss2/examples/ipv6/rpl-border-router/](examples/ipv6/rpl-border-router/).
|
|
|
|
Regressions tests
|
|
-----------------
|
|
Travis compile regression test for the platform:
|
|
[regression-tests/23-compile-avr](../../regression-tests/23-compile-avr).
|
|
|
|
This port adds newer version of `avr-gcc` compiler (4.9.2), to support
|
|
testing of newer Atmel MCU as Atmega256RFR2.
|
|
|
|
|
|
Board approvals
|
|
---------------
|
|
Summary:
|
|
* R&TTE 73/23/EEC, 89/336/EEC and 99/5/EC
|
|
* Safety: EN 60950-1:2006 + A12: 2011
|
|
* RF: ETSI EN 300 328 V1.7.1 (2006-10)
|
|
* EMC: ETSI EN 301 489-1 V1.9.2 (2011-09), ETSI EN 301 489-17 V2.2.1 (2012-09)
|
|
* EMF: EN 62479:2010
|
|
* Human exposure to electromagnetic fields: EN 62479:2010
|
|
|
|
Commercial availability
|
|
------------------------
|
|
Through vendor and though resellers. Note board is will only available
|
|
were CE approval is covered. This may be further restricted by WEEE.
|
|
Contact vendor. For research legislation is more relaxed in most
|
|
countries.
|
|
|
|
References
|
|
----------
|
|
AtMega64/128/256/RFR2 chip documentation available via Atmel.
|
|
Schematics and boards description. Available via Radio-Senors
|
|
Smart Reduced Power Consumption Techniques. AT02594 available via Atmel.
|
|
|
|
ToDo
|
|
-----
|
|
API for radio power saving settings introduced Atmels app note AT02594.
|
|
Also function for the desensitizing RPC resister.
|
|
|
|
Vendor info
|
|
-----------
|
|
http://radio-sensors.com/
|
|
|
|
Maintainer
|
|
----------
|
|
Robert Olsson <robert@radio-sensors.com>
|