dingusppc/zdocs/developers/heathrow.md
2024-04-15 07:01:51 -07:00

14 KiB

Heathrow ASIC

The Heathrow ASIC is an intergrated I/O controller designed for use in Power Macintosh G3 computers.

Its predecessors are Grand Central and O'Hare ASICs used in other Power Macintosh computers. As those names suggest, Apple engineers liked to name their I/O controllers after airports and train stations.

Heathrow and its siblings are collectively referred to as mac-io devices in the Open Firmware device tree.

Mac I/O family

The purpose of a Mac I/O (MIO) controller is to bring support for Apple legacy I/O hardware to the PCI-based Power Macintosh. That legacy hardware has existed long before Power Macintosh was introduced. It includes:

  • versatile interface adapter (VIA)
  • Sander-Woz integrated machine (SWIM) that is a floppy disk controller
  • CUDA MCU that controls ADB, parameter RAM, realtime clock and power management
  • serial communication controller (SCC)
  • Macintosh Enhanced SCSI Hardware (MESH)

In the 68k Macintosh era, all this hardware was implemented in separate ICs. In a PCI-compatible Power Macintosh, the above devices are part of the MIO chip itself. MIO's functional blocks implementing the above devices are called cells, i.e. "VIA cell", "SWIM cell" etc.

MIO itself is PCI compliant while the legacy hardware it emulates isn't. MIO occupies 512Kb of the PCI memory space divided into registers space and DMA space. Access to emulated legacy devices is accomplished by reading from/ writing to MIO's PCI address space at predefined offsets.

MIO includes a DMA controller that offers 15 DMA channels implementing Apple's own DMA protocol called descriptor-based DMA (DBDMA).

Official documentation (that is somewhat incomplete and erroneous) can be found in the second chapter of the book "Macintosh Technology in the Common Hardware Reference Platform" by Apple Computer, Inc.

Heathrow I/O modules

Being a Mac I/O compatible device, the Heathrow ASIC contains the following modules/cells:

  • VIA cell for establishing communication with the Cuda MCU (separate IC)
  • ATA/IDE cell for controlling ATA-3 compatible drives
  • enhanced serial communication controller (ESCC cell)
  • Ethernet controller cell funnily called bmac
  • floppy disk controller (SWIM3 cell)
  • SCSI controller (MESH cell)
  • integrated DBDMA controller
  • interrupt controller
  • logic for controlling built-in audio HW
  • logic for accessing NVRAM (separate IC)
  • logic for controlling a media bay on portables

PCI configuration space registers

Register name Default value
VendorID 0x106B (Apple)
DeviceID 0x0010
RevisionID 0x01
Class code 0xFF0000

It looks like Heathrow supports only one Base Address Register - BAR0. It contains base address of the memory-mapped registers programmed by system software during system initialization.

Memory-mapped registers

Software communicates with the Heathrow ASIC via memory-mapped registers that occupy 512 Kb starting from the base address located in the BAR0 register in the PCI configuration space.

Macintosh firmware configures the Heathrow ASIC to live at address 0xF3000000.

General chip control registers

Offset Register name Description
0x10 InterruptEvents2 each "1" bit indicates a pending int
0x14 InterruptMask2 enabling (1) / disabling(0) of specific ints
0x18 InterruptClear2 bit value "1" clears the corresponding int
0x1C InterruptLevels2 interrupt status for devices 32...63
0x20 InterruptEvents1 each "1" bit indicates a pending int
0x24 InterruptMask1 enabling (1) / disabling(0) of specific ints
0x28 InterruptClear1 bit value "1" clears the corresponding int
0x2C InterruptLevels1 interrupt status for devices 0...31
0x30 UnknownReg30 Not much is known about this register
0x34 HeathrowIDs bits for identifying media bay features?
0x38 FeatureControl bits for controlling Heathrow operation
0x3C AuxControl auxilary control bits

Device DMA spaces

Offset Size in bytes Space name
0x8000 256 MESH SCSI DMA
0x8100 256 Floppy controller DMA
0x8200 256 Ethernet transmit DMA
0x8300 256 Ethernet receive DMA
0x8400 256 Serial channel A transmit DMA
0x8500 256 Serial channel A receive DMA
0x8600 256 Serial channel B transmit DMA
0x8700 256 Serial channel B receive DMA
0x8800 256 Audio output DMA
0x8900 256 Audio input DMA  
0x8A00 256 unassigned DMA ?
0x8B00 256 internal ATA (IDE0) DMA
0x8C00 256 media bay (?) ATA (IDE1) DMA
0x8D00 256 unassigned DMA ?
0x8E00 256 unassigned DMA ?
0x8F00 256 unassigned DMA ?

Device register spaces

Offset Size Space name
0x10000 4 KB MESH SCSI controller registers
0x11000 4 KB Ethernet (bmac) controller registers
0x12000 4 KB Legacy serial (SCC) controller registers
0x13000 4 KB Serial (ESCC) controller registers
0x14000 4 KB Audio codec registers
0x15000 4 KB Floppy (SWIM3) controller registers
0x16000 8 KB VIA registers
0x20000 4 KB IDE0 registers
0x21000 4 KB IDE1 registers
0x60000 128 KB NVRAM access

Registers description

General chip control

Feature control register

Bit names in the table below were pulled from Open Firmware v2.4. The field "Description" represents my personal attempt to describe the function of those bits based on publicly available Apple and Linux sources.

Bit # Active Name Description
0 high in_use_led "1" enables monitor sense on G3 desktop
1 low -mb_pwr media bay power on/off
2 high pci_mb_en enable media bay PCI (?)
3 high ide_mb_en enable media bay ATA (IDE1)
4 high floppy_en enable floppy disk controller cell
5 high ide_int_en enable internal ATA (IDE0)
6 low -ide0_reset reset internal ATA
7 low -mb_reset reset media bay
8 high iobus_enable not available
9 high scc_enable enable SCC controller cell
10 high scsi_cell_en enable MESH SCSI controller cell
11 high swim_cell_en enable SWIM3 floppy controller cell
12 high snd_pwr not available
13 high snd_clk_en enable sound chip clock (?)
14 high scc_a_enable enable SCC channel A
15 high scc_b_enable enable SCC channel B
16 low -port_via switch VIA cell to portable mode (?)
16 high desktop_via switch VIA cell to desktop mode (?)
17 low -pwm not available
17 high mon_id not available
18 low -hookpb not available
18 high mb_cnt not available
19 low -swimiii floppy controller in SWIM3 mode (?)
19 high clonefloppy floppy controller in PC-compat mode (?)
20 high aud22run not available
21 high scsi_linkmode not available
22 high arb_bypass disable internal PCI arbiter (?)
23 low -ide1_reset reset media bay ATA
24 high slow_scc_pclk not available
25 high reset_scc reset serial (SCC) controller cell
26 high mfdc_cell_en enable PC-compat floppy controller (?)
27 high use_mfdc use PC floppy ctrl instead of SWIM3 ?
29 high enet_ctrl_en enable Ethernet controller cell (?)
30 high enet_xcvr_en enable Ethernet Transceiver (?)
31 high enet_reset reset Ethernet cell

Cell-specific registers

ATA cell registers

Internal ATA (IDE0)
Offset from I/O base Width in bits Function on read Function on write
0x20000 16 Data Data
0x20010 8 Error Features
0x20020 8 Sector Count Sector Count
0x20030 8 Sector Number Sector Number
0x20040 8 Cylinder Low Cylinder Low
0x20050 8 Cylinder High Cylinder High
0x20060 8 Drive/Head Drive/Head
0x20070 8 Status Command
0x20160 8 Alternate Status Device Control
0x20200 32 Timing Config Timing Config
Media Bay ATA (IDE1)
Offset from I/O base Width in bits Function on read Function on write
0x21000 16 Data Data
0x21010 8 Error Features
0x21020 8 Sector Count Sector Count
0x21030 8 Sector Number Sector Number
0x21040 8 Cylinder Low Cylinder Low
0x21050 8 Cylinder High Cylinder High
0x21060 8 Drive/Head Drive/Head
0x21070 8 Status Command
0x21160 8 Alternate Status Device Control
0x21200 32 Timing Config Timing Config
Timing Config Register

The timing config register is specific to Apple's ATA implementation. According with this source, this register is used to control timings for Multiword DMA (MDMA) and Programmed I/O (PIO) modes.

This register has the following format:

31 ... 22 21 20 ... 16 15 ... 11 10 9 ... 5 4 ... 0
Unused (?) HT MDMA Recovery MDMA Access E PIO Recovery PIO Access

I don't know what Recovery and Access values mean. It seems that all values are in 30 ns units. It corresponds to one PCI cycle when running at a 33 MHz clock speed.

Both PIO and MDMA recovery values are specified in x / 30 units after subtracting a constant offset. This offset is 120 ns for PIO transfers and 30 ns for MDMA transfers.

  • The "HT" stands for HalfTick. When set, 15 ns will be added to both MDMA access and recovery times. Otherwise, 30 ns are added to the MDMA recovery time.
  • The "E" bit, when set, adds 30 ns to the final PIO timing.

The official Apple source specifies the following default values for each PIO mode:

Mode # Cycle time Transfer rate Recovery Access
0 600 ns 3,33 MB/s 420 ns 180 ns
1 390 ns 5,13 MB/s 240 ns 150 ns
2 360 ns 5,56 MB/s 180 ns 180 ns
3 330 ns 6,1 MB/s 180 ns 150 ns
4 300 ns 6,67 MB/s 150 ns 150 ns

Timing values for the PIO modes 2...4 deviate from the corresponding values given in the ATA-3 specification.

PIO cycle time can be calculated using the following equation:

PIO_Cycle_ns = PIO_Recovery * 30 + 120 + PIO_Access * 30 + E * 30

Multiword DMA modes are specified as follows:

Mode # Cycle time Transfer rate Recovery Access
0 480 ns 4,17 MB/s 240 ns 240 ns
1 360 ns 5,56 MB/s 180 ns 180 ns
2 270 ns 7,4 MB/s 135 ns 135 ns
3 240 ns 8,33 MB/s 120 ns 120 ns
4 210 ns 9,52 MB/s 105 ns 105 ns
5 180 ns 11,11 MB/s 90 ns 90 ns
6 150 ns 13,33 MB/s 75 ns 75 ns
7 120 ns 16,67 MB/s 45 ns 75 ns

Modes 0, 6 and 7 from the table above correspond to the MDMA modes 0...2 specified in the ATA-2 standard.

MDMA cycle time can be calculated using the following equation:

MDMA_Cycle_ns = MDMA_Recovery * 30 + MDMA_Access * 30 + 30