insertions.
The old behavior could cause arbitrarily bad memory usage in the DAG
combiner if there was heavy traffic of adding nodes already on the
worklist to it. This commit switches the DAG combine worklist to work
the same way as the instcombine worklist where we null-out removed
entries and only add new entries to the worklist. My measurements of
codegen time shows slight improvement. The memory utilization is
unsurprisingly dominated by other factors (the IR and DAG itself
I suspect).
This change results in subtle, frustrating churn in the particular order
in which DAG combines are applied which causes a number of minor
regressions where we fail to match a pattern previously matched by
accident. AFAICT, all of these should be using AddToWorklist to directly
or should be written in a less brittle way. None of the changes seem
drastically bad, and a few of the changes seem distinctly better.
A major change required to make this work is to significantly harden the
way in which the DAG combiner handle nodes which become dead
(zero-uses). Previously, we relied on the ability to "priority-bump"
them on the combine worklist to achieve recursive deletion of these
nodes and ensure that the frontier of remaining live nodes all were
added to the worklist. Instead, I've introduced a routine to just
implement that precise logic with no indirection. It is a significantly
simpler operation than that of the combiner worklist proper. I suspect
this will also fix some other problems with the combiner.
I think the x86 changes are really minor and uninteresting, but the
avx512 change at least is hiding a "regression" (despite the test case
being just noise, not testing some performance invariant) that might be
looked into. Not sure if any of the others impact specific "important"
code paths, but they didn't look terribly interesting to me, or the
changes were really minor. The consensus in review is to fix any
regressions that show up after the fact here.
Thanks to the other reviewers for checking the output on other
architectures. There is a specific regression on ARM that Tim already
has a fix prepped to commit.
Differential Revision: http://reviews.llvm.org/D4616
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213727 91177308-0d34-0410-b5e6-96231b3b80d8
There are a few more cleanups to do, but I ran into some problems
with ext loads and trunc stores, when I tried to change some of the
vector loads and stores from custom to legal, so I wasn't able to
get rid of everything.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213552 91177308-0d34-0410-b5e6-96231b3b80d8
This implements a solution for constant initializers suggested
by Vadim Girlin, where we store the data after the shader code
and then use the S_GETPC instruction to compute its address.
This saves use the trouble of creating a new buffer for constant data
and then having to pass the pointer to the kernel via user SGPRs or the
input buffer.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213530 91177308-0d34-0410-b5e6-96231b3b80d8
This probably was killed by some generic DAGCombiner
improvements in checking the TargetBooleanContents instead
of just 1.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213471 91177308-0d34-0410-b5e6-96231b3b80d8
These instructions can only take a limited input range, and return
the constant value 1 out of range. We should do range reduction to
be able to process arbitrary values. Use a FRACT instruction after
normalization to achieve this. Also add a test for constant folding
with the lowered code with unsafe-fp-math enabled.
v2: use DAG lowering instead of intrinsic, adapt test
v3: calculate constant, fold pattern into instruction definition
v4: misc style fixes, add sin-fold testcase, cosmetics
Patch by Grigori Goronzy
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213458 91177308-0d34-0410-b5e6-96231b3b80d8
Actual support for softening f16 operations is still limited, and can be added
when it's needed. But Soften is much closer to being a useful thing to try
than keeping it Legal when no registers can actually hold such values.
Longer term, we probably want something between Soften and Promote semantics
for most targets, it'll be more efficient to promote the 4 basic operations to
f32 than libcall them.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213372 91177308-0d34-0410-b5e6-96231b3b80d8
This test is actually going in the opposite direction to what the
filename and function name suggested.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213358 91177308-0d34-0410-b5e6-96231b3b80d8
Unfortunately, we don't seem to have a direct truncation, but the
extension can be legally split into two operations so we should
support that.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213357 91177308-0d34-0410-b5e6-96231b3b80d8
This makes the two intrinsics @llvm.convert.from.f16 and
@llvm.convert.to.f16 accept types other than simple "float". This is
only strictly needed for the truncate operation, since otherwise
double rounding occurs and there's no way to represent the strict IEEE
conversion. However, for symmetry we allow larger types in the extend
too.
During legalization, we can expand an "fp16_to_double" operation into
two extends for convenience, but abort when the truncate isn't legal. A new
libcall is probably needed here.
Even after this commit, various target tweaks are needed to actually use the
extended intrinsics. I've put these into separate commits for clarity, so there
are no actual tests of f64 conversion here.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213248 91177308-0d34-0410-b5e6-96231b3b80d8
Assuming single precision denormals and accurate sqrt/div are not
reported, this passes the OpenCL conformance test.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213089 91177308-0d34-0410-b5e6-96231b3b80d8
v2: use ffbh/l if available
v3: Rebase on top of Matt's SI patches
Signed-off-by: Jan Vesely <jan.vesely@rutgers.edu>
Reviewed-by: Tom Stellard <tom@stellard.net>
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213072 91177308-0d34-0410-b5e6-96231b3b80d8
This helps avoid redundant instructions to unpack, and repack
the vectors. Ideally we could recognize that pattern and eliminate
it. Currently v4i8 and other small element type vectors are scalarized,
so this has the added bonus of avoiding that.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@213031 91177308-0d34-0410-b5e6-96231b3b80d8
We need the intrinsics with offsets, so why not just add them all.
The R128 parameter will also be useful for reducing SGPR usage.
GL_ARB_image_load_store also adds some image GLSL modifiers like "coherent",
so Mesa will probably translate those to slc, glc, etc.
When LLVM 3.5 is released, I'll switch Mesa to these new intrinsics.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@212830 91177308-0d34-0410-b5e6-96231b3b80d8
Use alg. from LegalizeDAG.cpp
Move Expand setting to SIISellowering
v2: Extend existing tests instead of creating new ones
v3: use separate LowerFPTOSINT function
v4: use TargetLowering::expandFP_TO_SINT
add comment about using FP_TO_SINT for uints
Signed-off-by: Jan Vesely <jan.vesely@rutgers.edu>
Reviewed-by: Tom Stellard <tom@stellard.net>
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@212773 91177308-0d34-0410-b5e6-96231b3b80d8
Fixes various bugs with reordering loads and stores.
Scalarized vector loads weren't collecting the chains
at all.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@212473 91177308-0d34-0410-b5e6-96231b3b80d8
The default rounding mode to initialize the mode register needs
to be reported to the runtime. Fill in other bits a kernel
may be interested in setting for future use.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@211791 91177308-0d34-0410-b5e6-96231b3b80d8
R600 was using a clamped version of rsq, but SI was not. Add a
new rsq_clamped intrinsic and use them consistently.
It's unclear to me from the documentation what behavior
the R600 instructions have, so I assume they have the legacy behavior
described by the SI documents. For R600, use RECIPSQRT_IEEE
for both llvm.AMDGPU.rsq.legacy and llvm.AMDGPU.rsq. R600 also
has RECIPSQRT_FF, which I'm not sure how it fits in here.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@211637 91177308-0d34-0410-b5e6-96231b3b80d8
v2: move < %s to the end of the line
space after ;
add v4i32 test
Signed-off-by: Jan Vesely <jan.vesely@rutgers.edu>
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@211476 91177308-0d34-0410-b5e6-96231b3b80d8
