Look for patterns of the form (store (load ...), ...) in which the two
locations are known not to partially overlap. (Identical locations are OK.)
These sequences are better implemented by MVC unless either the load or
the store could use RELATIVE LONG instructions.
The testcase showed that we weren't using LHRL and LGHRL for extload16,
only sextloadi16. The patch fixes that too.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185919 91177308-0d34-0410-b5e6-96231b3b80d8
Use "STC;MVC" for memsets that are too big for two STCs or MV...Is yet
small enough for a single MVC. As with memcpy, I'm leaving longer cases
till later.
The number of tests might seem excessive, but f33 & f34 from memset-04.ll
failed the first cut because I'd not added the "?:" on the calculation
of Size1.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185918 91177308-0d34-0410-b5e6-96231b3b80d8
Use MVC for memcpy in cases where a single MVC is enough. Using MVC is
a win for longer copies too, but I'll leave that for later.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185802 91177308-0d34-0410-b5e6-96231b3b80d8
The stack coloring pass has code to delete stores and loads that become
trivially dead after coloring. Extend it to cope with single instructions
that copy from one frame index to another.
The testcase happens to show an example of this kicking in at the moment.
It did occur in Real Code too though.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185705 91177308-0d34-0410-b5e6-96231b3b80d8
The stack coloring pass renumbered frame indexes with a loop of the form:
for each frame index FI
for each instruction I that uses FI
for each use of FI in I
rename FI to FI'
This caused problems if an instruction used two frame indexes F0 and F1
and if F0 was renamed to F1 and F1 to F2. The first time we visited the
instruction we changed F0 to F1, then we changed both F1s to F2.
In other words, the problem was that SSRefs recorded which instructions
used an FI, but not which MachineOperands and MachineMemOperands within
that instruction used it.
This is easily fixed for MachineOperands by walking the instructions
once and processing each operand in turn. There's already a loop to
do that for dead store elimination, so it seemed more efficient to
fuse the two at the block level.
MachineMemOperands are more tricky because they can be shared between
instructions. The patch handles them by making SSRefs an array of
MachineMemOperands rather than an array of MachineInstrs. We might end
up processing the same MachineMemOperand twice, but that's OK because
we always know from the SSRefs index what the original frame index was.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185703 91177308-0d34-0410-b5e6-96231b3b80d8
...now that the problem that prompted the restriction has been fixed.
The original spill-02.py was a compromise because at the time I couldn't
find an example that actually failed without the two scavenging slots.
The version included here did.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185701 91177308-0d34-0410-b5e6-96231b3b80d8
This is another prerequisite for frame-to-frame MVC copies.
I'll commit the patch that makes use of the slot separately.
The downside of trying to test many corner cases with each of the
available addressing modes is that a fair few tests need to account
for the new frame layout. I do still think it's useful to have all
these tests though, since it's something that wouldn't get much coverage
otherwise.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185698 91177308-0d34-0410-b5e6-96231b3b80d8
Add a mapping from register-based <INSN>R instructions to the corresponding
memory-based <INSN>. Use it to cut down on the number of spill loads.
Some instructions extend their operands from smaller fields, so this
required a new TSFlags field to say how big the unextended operand is.
This optimisation doesn't trigger for C(G)R and CL(G)R because in practice
we always combine those instructions with a branch. Adding a test for every
other case probably seems excessive, but it did catch a missed optimisation
for DSGF (fixed in r185435).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185529 91177308-0d34-0410-b5e6-96231b3b80d8
Fixes some cases where we were using full 64-bit division for (sdiv i32, i32)
and (sdiv i64, i32).
The "32" in "SDIVREM32" just refers to the second operand. The first operand
of all *DIVREM*s is a GR128.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185435 91177308-0d34-0410-b5e6-96231b3b80d8
Try to use MVC when spilling the destination of a simple load or the source
of a simple store. As explained in the comment, this doesn't yet handle
the case where the load or store location is also a frame index, since
that could lead to two simultaneous scavenger spills, something the
backend can't handle yet. spill-02.py tests that this restriction kicks in,
but unfortunately I've not yet found a case that would fail without it.
The volatile trick I used for other scavenger tests doesn't work here
because we can't use MVC for volatile accesses anyway.
I'm planning on relaxing the restriction later, hopefully with a test
that does trigger the problem...
Tests @f8 and @f9 also showed that L(G)RL and ST(G)RL were wrongly
classified as SimpleBDX{Load,Store}. It wouldn't be easy to test for
that bug separately, which is why I didn't split out the fix as a
separate patch.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185434 91177308-0d34-0410-b5e6-96231b3b80d8
Add pseudo conditional store instructions, so that we use:
branch foo:
store
foo:
instead of:
load
branch foo:
move
foo:
store
z196 has real 32-bit and 64-bit conditional stores, but we don't use
any z196 instructions yet.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@185065 91177308-0d34-0410-b5e6-96231b3b80d8
Unlike most -- hopefully "all other", but I'm still checking -- memory
instructions we support, LOAD REVERSED and STORE REVERSED may access
the memory location several times. This means that they are not suitable
for volatile loads and stores.
This patch is a prerequisite for better atomic load and store support.
The same principle applies there: almost all memory instructions we
support are inherently atomic ("block concurrent"), but LOAD REVERSED
and STORE REVERSED are exceptions.
Other instructions continue to allow volatile operands. I will add
positive "allows volatile" tests at the same time as the "allows atomic
load or store" tests.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@183002 91177308-0d34-0410-b5e6-96231b3b80d8
The code to distinguish between unaligned and aligned addresses was
already there, so this is mostly just a switch-on-and-test process.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182920 91177308-0d34-0410-b5e6-96231b3b80d8
This patch adds support for the CRJ and CGRJ instructions. Support for
the immediate forms will be a separate patch.
The architecture has a large number of comparison instructions. I think
it's generally better to concentrate on using the "best" comparison
instruction first and foremost, then only use something like CRJ if
CR really was the natual choice of comparison instruction. The patch
therefore opportunistically converts separate CR and BRC instructions
into a single CRJ while emitting instructions in ISelLowering.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182764 91177308-0d34-0410-b5e6-96231b3b80d8
Before this change, the SystemZ backend would use BRCL for all branches
and only consider shortening them to BRC when generating an object file.
E.g. a branch on equal would use the JGE alias of BRCL in assembly output,
but might be shortened to the JE alias of BRC in ELF output. This was
a useful first step, but it had two problems:
(1) The z assembler isn't traditionally supposed to perform branch shortening
or branch relaxation. We followed this rule by not relaxing branches
in assembler input, but that meant that generating assembly code and
then assembling it would not produce the same result as going directly
to object code; the former would give long branches everywhere, whereas
the latter would use short branches where possible.
(2) Other useful branches, like COMPARE AND BRANCH, do not have long forms.
We would need to do something else before supporting them.
(Although COMPARE AND BRANCH does not change the condition codes,
the plan is to model COMPARE AND BRANCH as a CC-clobbering instruction
during codegen, so that we can safely lower it to a separate compare
and long branch where necessary. This is not a valid transformation
for the assembler proper to make.)
This patch therefore moves branch relaxation to a pre-emit pass.
For now, calls are still shortened from BRASL to BRAS by the assembler,
although this too is not really the traditional behaviour.
The first test takes about 1.5s to run, and there are likely to be
more tests in this vein once further branch types are added. The feeling
on IRC was that 1.5s is a bit much for a single test, so I've restricted
it to SystemZ hosts for now.
The patch exposes (and fixes) some typos in the main CodeGen/SystemZ tests.
A later patch will remove the {{g}}s from that directory.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@182274 91177308-0d34-0410-b5e6-96231b3b80d8
This adds all CodeGen tests for the SystemZ target.
This version of the patch incorporates feedback from a review by
Sean Silva. Thanks to all reviewers!
Patch by Richard Sandiford.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@181204 91177308-0d34-0410-b5e6-96231b3b80d8
Note that this actually changes code generation, and someone who
understands this target better should check the changes.
- R12Q is now allocatable. I think it was omitted from the allocation
order by mistake since it isn't reserved. It as apparently used as a
GOT pointer sometimes, and it should probably be reserved if that is
the case.
- The GR64 registers are allocated in a different order now. The
register allocator will automatically put the CSRs last. There were
other changes to the order that may have been significant.
The test fix is because r0 and r1 swapped places in the allocation order.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@133067 91177308-0d34-0410-b5e6-96231b3b80d8
replace the check with the appropriate predicate. Modify the testcase to reflect
the correct code. (It should be saving callee-saved registers on the stack
allocated by the calling fuction.)
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@103829 91177308-0d34-0410-b5e6-96231b3b80d8
(OP (trunc x), (trunc y)) -> (trunc (OP x, y))
Unfortunately this simple change causes dag combine to infinite looping. The problem is the shrink demanded ops optimization tend to canonicalize expressions in the opposite manner. That is badness. This patch disable those optimizations in dag combine but instead it is done as a late pass in sdisel.
This also exposes some deficiencies in dag combine and x86 setcc / brcond lowering. Teach them to look pass ISD::TRUNCATE in various places.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@92849 91177308-0d34-0410-b5e6-96231b3b80d8
