Macintosh-HW/BlueSCSI
1
0
Fork 0
mirror of https://github.com/erichelgeson/BlueSCSI.git synced 2024-11-21 15:31:00 +00:00
Code Issues Projects Releases Wiki Activity
Page: BlueSCSI 1.0 a b c Assembly
Pages
3D Cases Adapters & Accessories Advanced Settings Assembly BluePill (STM32) Compatibility (Clones Fakes) BlueSCSI 1.0 a b c Assembly BlueSCSI 1.1 DB25 Assembly BlueSCSI 1.1 Desktop Assembly CD Image Support Disk Drivers (Mac) Disk Drives (PC) External LED Flashing (Advanced) Flashing Getting Started Home Image File Fragmentation Image Sets Mac CD to HDD (Hack!) Manual Testing Dev Performance SCSI Vendor Config SD Cards ST Link Setup Slow SPI Supported Systems Termination Transferring files (Mac) Troubleshooting Usage Variants
4 BlueSCSI 1.0 a b c Assembly
Eric Helgeson edited this page 2024-06-17 09:39:56 -05:00
Table of Contents

Important

If you are looking for BlueSCSI v2 documentation please go here: https://github.com/BlueSCSI/BlueSCSI-v2/wiki

BlueSCSI 1.0 A/B/C Assembly

Before you start

Read through all instructions before starting.

Verify you have all the components

  • Preprogrammed STM32 BluePill with 2x 20 pin headers
  • BlueSCSI 1.0 PCB
  • 2x Diodes
  • 50 pin male SCSI connector
  • 2x 220ohm Resistor Networks
  • 2x 330ohm Resistor Networks
  • MicroSD Socket
  • Berg connector
  • 2x 2 pin headers with jumpers
  • 3d printed bracket

Videos

Assembly videos created by the community so far

Stephen Arsenault - BlueSCSI Kit Assembly 2:52

Joe's Computer Museum - A New Challenger - BlueSCSI - #MARCHintosh Review 26:52

Geeky Bit - Tutorial - BlueSCSI Assembly 20:35

Building

  1. Solder the surface mount SD Card holder onto the board. Use the Drag Solder technique

    • Once on, check continuity of all connections. Fixing this after the BluePill is on will be difficult.
    • Ensure the SD card fits and you dont have too much solder on the sides or contacts - if you do, you can use solder wick to clean some off

  2. Solder the diode to the bottom of the board, ensure it is as flush with the PCB as possible. Trim the excess legs

  1. Solder the header pins on to the BluePill. Then BluePill pill to the BlueSCSI PCB.

    • Correct orientation is having the USB connector of the BluePill should be over the SD Card holder.
    • NOTE: Consider adding headers to the board if you would like to have the BluePill removable.

  2. Solder on the resistor nets. Pin one is marked on the board and the resistors.

    • 220 RNETS (RN1 & RN3) are closest to the BluePill - NOTE PIN one on each - they are opposite of eachtoher. See photo.
    • 330 RNETS (RN2 & RN4) are furthest from the BluePill - NOTE PIN one on each - they are opposite of eachtoher. See photo.

  3. Solder on the Termination Jumpers & place the jumpers on to enable Termiation

  4. Solder the 50 Pin headers on.

    • Note Pin 1 and Box header on the silk screen.

  5. Solder on the berg connector. Only needed if your machine does not supply enough power via the SCSI bus, but recommended to solder on if you have the connector

  6. Not recommended anymore - Solder on the debug headers near the SD card. Only needed for debugging, requires a special firmware. Headers have been removed from the new PCB revisions

Fully Assembled

  1. Configure it
  2. Test it!
  • Plug it into your favorite Mac, run a benchmark with SCSI Director Pro, play some Lemmings, write a document in ClarisWorks, enjoy!

Version 1.0-b & 1.0-c BOM

Note on Right angle connectors - Right angle connectors are not notched the correct way, PCB rev 1.1 fixes that Optional

BlueSCSI Logo

Important

If you are looking for BlueSCSI v2 documentation please go here: https://github.com/BlueSCSI/BlueSCSI-v2/wiki