have their low bits set to zero. This allows us to optimize
out explicit stack alignment code like in stack-align.ll:test4 when
it is redundant.
Doing this causes the code generator to start turning FI+cst into
FI|cst all over the place, which is general goodness (that is the
canonical form) except that various pieces of the code generator
don't handle OR aggressively. Fix this by introducing a new
SelectionDAG::isBaseWithConstantOffset predicate, and using it
in places that are looking for ADD(X,CST). The ARM backend in
particular was missing a lot of addressing mode folding opportunities
around OR.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@125470 91177308-0d34-0410-b5e6-96231b3b80d8
The vld1-lane, vld1-dup and vst1-lane instructions do not yet support using
post-increment versions, but all the rest of the NEON load/store instructions
should be handled now.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@125014 91177308-0d34-0410-b5e6-96231b3b80d8
These operations are expanded to pairs of loads or stores, and the first one
uses the address register update to produce the address for the second one.
So far, the second load/store has also updated the address register, just
for convenience, since that output has never been used. In anticipation of
actually supporting post-increment updates for these operations, this changes
the non-updating operations to use a non-updating load/store for the second
instruction.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@125013 91177308-0d34-0410-b5e6-96231b3b80d8
TargetInstrInfo:
Change produceSameValue() to take MachineRegisterInfo as an optional argument.
When in SSA form, targets can use it to make more aggressive equality analysis.
Machine LICM:
1. Eliminate isLoadFromConstantMemory, use MI.isInvariantLoad instead.
2. Fix a bug which prevent CSE of instructions which are not re-materializable.
3. Use improved form of produceSameValue.
ARM:
1. Teach ARM produceSameValue to look pass some PIC labels.
2. Look for operands from different loads of different constant pool entries
which have same values.
3. Re-implement PIC GA materialization using movw + movt. Combine the pair with
a "add pc" or "ldr [pc]" to form pseudo instructions. This makes it possible
to re-materialize the instruction, allow machine LICM to hoist the set of
instructions out of the loop and make it possible to CSE them. It's a bit
hacky, but it significantly improve code quality.
4. Some minor bug fixes as well.
With the fixes, using movw + movt to materialize GAs significantly outperform the
load from constantpool method. 186.crafty and 255.vortex improved > 20%, 254.gap
and 176.gcc ~10%.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@123905 91177308-0d34-0410-b5e6-96231b3b80d8
movw r0, :lower16:(L_foo$non_lazy_ptr-(LPC0_0+4))
movt r0, :upper16:(L_foo$non_lazy_ptr-(LPC0_0+4))
LPC0_0:
add r0, pc, r0
It's not yet enabled by default as some tests are failing. I suspect bugs in
down stream tools.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@123619 91177308-0d34-0410-b5e6-96231b3b80d8
earlyclobber stuff. This should fix PRs 2313 and 8157.
Unfortunately, no testcase, since it'd be dependent on register
assignments.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@122663 91177308-0d34-0410-b5e6-96231b3b80d8
instruction based on the t_addrmode_s# mode and what it returned. There is some
obvious badness to this. In particular, it's hard to do MC-encoding when the
instruction may change out from underneath you after the t_addrmode_s# variable
is finally resolved.
The solution is to revert a long-ago change that merged the reg/reg and reg/imm
versions. There is the addition of several new addressing modes. They no longer
have extraneous operands associated with them. I.e., if it's reg/reg we don't
have to have a dummy zero immediate tacked on to the SDNode.
There are some obvious cleanups here, which will happen shortly.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@121747 91177308-0d34-0410-b5e6-96231b3b80d8
Alignments smaller than the total size of the memory being loaded or stored,
unless the alignment is 8 bytes, are not allowed. Add tests for this, too.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@121506 91177308-0d34-0410-b5e6-96231b3b80d8
difficult on current ARM implementations for a few reasons.
1. Even though a single vmla has latency that is one cycle shorter than a pair
of vmul + vadd, a RAW hazard during the first (4? on Cortex-a8) can cause
additional pipeline stall. So it's frequently better to single codegen
vmul + vadd.
2. A vmla folowed by a vmul, vmadd, or vsub causes the second fp instruction to
stall for 4 cycles. We need to schedule them apart.
3. A vmla followed vmla is a special case. Obvious issuing back to back RAW
vmla + vmla is very bad. But this isn't ideal either:
vmul
vadd
vmla
Instead, we want to expand the second vmla:
vmla
vmul
vadd
Even with the 4 cycle vmul stall, the second sequence is still 2 cycles
faster.
Up to now, isel simply avoid codegen'ing fp vmla / vmls. This works well enough
but it isn't the optimial solution. This patch attempts to make it possible to
use vmla / vmls in cases where it is profitable.
A. Add missing isel predicates which cause vmla to be codegen'ed.
B. Make sure the fmul in (fadd (fmul)) has a single use. We don't want to
compute a fmul and a fmla.
C. Add additional isel checks for vmla, avoid cases where vmla is feeding into
fp instructions (except for the #3 exceptional case).
D. Add ARM hazard recognizer to model the vmla / vmls hazards.
E. Add a special pre-regalloc case to expand vmla / vmls when it's likely the
vmla / vmls will trigger one of the special hazards.
Work in progress, only A+B are enabled.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120960 91177308-0d34-0410-b5e6-96231b3b80d8
with a SimpleValueType, while an EVT supports equality and
inequality comparisons with SimpleValueType.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118169 91177308-0d34-0410-b5e6-96231b3b80d8
explicit about the operands. Split out the different variants into separate
instructions. This gives us the ability to, among other things, assign
different scheduling itineraries to the variants. rdar://8477752.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117409 91177308-0d34-0410-b5e6-96231b3b80d8
which require the use of the shifter-operand. This will be used to split
the ldr/str instructions such that those versions needing the shifter operand
can get a different scheduling itenerary, as in some cases, the use of the
shifter can cause different scheduling than the simpler forms.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@115066 91177308-0d34-0410-b5e6-96231b3b80d8
passed the root of the match, even though only a few patterns
actually needed this (one in X86, several in ARM [which should
be refactored anyway], and some in CellSPU that I don't feel
like detangling). Instead of requiring all ComplexPatterns to
take the dead root, have targets opt into getting the root by
putting SDNPWantRoot on the ComplexPattern.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@114471 91177308-0d34-0410-b5e6-96231b3b80d8
pseudo-instruction approach. Change ARMExpandPseudoInsts to use a table
to record all the NEON load/store information.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@113812 91177308-0d34-0410-b5e6-96231b3b80d8
instructions prior to regalloc. Since it's getting a little close to
the 2.8 branch deadline, I'll have to leave the rest of the instructions
handled by the NEONPreAllocPass for now, but I didn't want to leave half
of the VLD instructions converted and the other half not.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@112983 91177308-0d34-0410-b5e6-96231b3b80d8
int x(int t) {
if (t & 256)
return -26;
return 0;
}
We generate this:
tst.w r0, #256
mvn r0, #25
it eq
moveq r0, #0
while gcc generates this:
ands r0, r0, #256
it ne
mvnne r0, #25
bx lr
Scandalous really!
During ISel time, we can look for this particular pattern. One where we have a
"MOVCC" that uses the flag off of a CMPZ that itself is comparing an AND
instruction to 0. Something like this (greatly simplified):
%r0 = ISD::AND ...
ARMISD::CMPZ %r0, 0 @ sets [CPSR]
%r0 = ARMISD::MOVCC 0, -26 @ reads [CPSR]
All we have to do is convert the "ISD::AND" into an "ARM::ANDS" that sets [CPSR]
when it's zero. The zero value will all ready be in the %r0 register and we only
need to change it if the AND wasn't zero. Easy!
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@112664 91177308-0d34-0410-b5e6-96231b3b80d8
all the other LDM/STM instructions. This fixes asm printer crashes when
compiling with -O0. I've changed one of the NEON tests (vst3.ll) to run
with -O0 to check this in the future.
Prior to this change VLDM/VSTM used addressing mode #5, but not really.
The offset field was used to hold a count of the number of registers being
loaded or stored, and the AM5 opcode field was expanded to specify the IA
or DB mode, instead of the standard ADD/SUB specifier. Much of the backend
was not aware of these special cases. The crashes occured when rewriting
a frameindex caused the AM5 offset field to be changed so that it did not
have a valid submode. I don't know exactly what changed to expose this now.
Maybe we've never done much with -O0 and NEON. Regardless, there's no longer
any reason to keep a count of the VLDM/VSTM registers, so we can use
addressing mode #4 and clean things up in a lot of places.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@112322 91177308-0d34-0410-b5e6-96231b3b80d8
