As Bill Schmidt pointed out to me, only on Darwin do we need to spill/restore
VRSAVE in the SjLj code. For non-Darwin, don't spill/restore VRSAVE (and I've
added some asserts to make sure that we're not).
As it turns out, we're not currently handling the Darwin case correctly (I've
added a FIXME in the test case). I've tried adding various implied register
definitions/uses to force the spill without success, so I'll need to address
this later.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@178096 91177308-0d34-0410-b5e6-96231b3b80d8
All Intel CPUs since Yonah look a lot alike, at least at the granularity
of the scheduling models. We can add more accurate models for
processors that aren't Sandy Bridge if required. Haswell will probably
need its own.
The Atom processor and anything based on NetBurst is completely
different. So are the non-Intel chips.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@178080 91177308-0d34-0410-b5e6-96231b3b80d8
Now that the register scavenger can support multiple spill slots, and PEI can
use virtual-register-based scavenging for multiple simultaneous registers, we
can use a virtual register for the transfer register in the CR spilling code.
This should eliminate the last place (outside of the prologue/epilogue) where
we depend on the unconditional availability of the r0 register. We will soon be
able to allocate it (in a somewhat restricted sense) as a GPR.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@178060 91177308-0d34-0410-b5e6-96231b3b80d8
The previous algorithm could not deal properly with scavenging multiple virtual
registers because it kept only one live virtual -> physical mapping (and
iterated through operands in order). Now we don't maintain a current mapping,
but rather use replaceRegWith to completely remove the virtual register as
soon as the mapping is established.
In order to allow the register scavenger to return a physical register killed
by an instruction for definition by that same instruction, we now call
RS->forward(I) prior to eliminating virtual registers defined in I. This
requires a minor update to forward to ignore virtual registers.
These new features will be tested in forthcoming commits.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@178058 91177308-0d34-0410-b5e6-96231b3b80d8
- 'prefetch' intrinsics are only lowered when SSE is available. On non-X86
builds, 'generic' CPU is used and stops lowering any prefetch intrinsics.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@178046 91177308-0d34-0410-b5e6-96231b3b80d8
They read from constant register space anyway.
v2: fix lit tests
Signed-off-by: Christian König <christian.koenig@amd.com>
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@178020 91177308-0d34-0410-b5e6-96231b3b80d8
- It's still considered aligned when the specified alignment is larger
than the natural alignment;
- The new alignment for the high 128-bit vector should be min(16,
alignment) as the pointer is advanced by 16, a power-of-2 offset.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177947 91177308-0d34-0410-b5e6-96231b3b80d8
- Handle the case where the result of 'insert_subvect' is bitcasted
before 'extract_subvec'. This removes the redundant insertf128/extractf128
pair on unaligned 256-bit vector load/store on vectors of non 64-bit integer.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177945 91177308-0d34-0410-b5e6-96231b3b80d8
For instance, following transformation will be disabled:
x + x + x => 3.0f * x;
The problem of these transformations is that it introduces a FP constant, which
following Instruction-Selection pass cannot handle.
Reviewed by Nadav, thanks a lot!
rdar://13445387
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177933 91177308-0d34-0410-b5e6-96231b3b80d8
I know it is incorrect and they'd fail with +Asserts for win32 targets, though.
I'll try to fix them tonight.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177914 91177308-0d34-0410-b5e6-96231b3b80d8
test/CodeGen/Generic/2008-02-20-MatchingMem.ll: Test contains inline assembly not supported by Hexagon.
Following tests are XFAILed due to multiple return values which Hexagon doesn't support.
test/CodeGen/Generic/multiple-return-values-cross-block-with-invoke.ll
test/CodeGen/Generic/select-cc.ll
test/CodeGen/Generic/vector.ll
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177912 91177308-0d34-0410-b5e6-96231b3b80d8
Performing this check unilaterally prevented us from generating FMAs when the incoming IR contained illegal vector types which would eventually be legalized to underlying types that *did* support FMA.
For example, an @llvm.fmuladd on an OpenCL float16 should become a sequence of float4 FMAs, not float4 fmul+fadd's.
NOTE: Because we still call the target-specific profitability hook, individual targets can reinstate the old behavior, if desired, by simply performing the legality check inside their callback hook. They can also perform more sophisticated legality checks, if, for example, some illegal vector types can be productively implemented as FMAs, but not others.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177820 91177308-0d34-0410-b5e6-96231b3b80d8
Thanks to Jakob for isolating the underlying problem from the
test case in r177423. The original commit had introduced
asymmetric copy operations, but these turned out to be a work-around
to the real problem (the use of == instead of hasSubClassEq in PPCCTRLoops).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177679 91177308-0d34-0410-b5e6-96231b3b80d8
This implements SJLJ lowering on PPC, making the Clang functions
__builtin_{setjmp/longjmp} functional on PPC platforms. The implementation
strategy is similar to that on X86, with the exception that a branch-and-link
variant is used to get the right jump address. Credit goes to Bill Schmidt for
suggesting the use of the unconditional bcl form (instead of the regular bl
instruction) to limit return-address-cache pollution.
Benchmarking the speed at -O3 of:
static jmp_buf env_sigill;
void foo() {
__builtin_longjmp(env_sigill,1);
}
main() {
...
for (int i = 0; i < c; ++i) {
if (__builtin_setjmp(env_sigill)) {
goto done;
} else {
foo();
}
done:;
}
...
}
vs. the same code using the libc setjmp/longjmp functions on a P7 shows that
this builtin implementation is ~4x faster with Altivec enabled and ~7.25x
faster with Altivec disabled. This comparison is somewhat unfair because the
libc version must also save/restore the VSX registers which we don't yet
support.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177666 91177308-0d34-0410-b5e6-96231b3b80d8
Although there is only one Altivec VRSAVE register, it is a member of
a register class, and we need the ability to spill it. Because this
register is normally callee-preserved and handled by special code this
has never before been necessary. However, this capability will be required by
a forthcoming commit adding SjLj support.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177654 91177308-0d34-0410-b5e6-96231b3b80d8
The old code used to lower FRAMEADDR tried to replicate the logic in the real
frame-lowering code that determines whether or not the frame pointer (r31) will
be used. When it seemed as through the frame pointer would not be used, the
stack pointer (r1) was used instead. Unfortunately, because the stack size is
not yet known, this does not work. Instead, this change introduces new
always-reserved pseudo-registers (FP and FP8) that are replaced during prologue
insertion with the real frame-pointer register (either r1 or r31).
It is important that this intrinsic always return a valid frame address because
it is used by Clang to store the frame address as part of code generation for
__builtin_setjmp.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177653 91177308-0d34-0410-b5e6-96231b3b80d8
NEON is not IEEE 754 compliant, so we should avoid lowering single-precision
floating point operations with NEON unless unsafe-math is turned on. The
equivalent VFP instructions are IEEE 754 compliant, but in some cores they're
much slower, so some archs/OSs might still request it to be on by default,
such as Swift and Darwin.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177651 91177308-0d34-0410-b5e6-96231b3b80d8
- Move SRA/SRL/SHL lowering support from DAG combination to DAG lowering
to support extended 256-bit integer in AVX but not AVX2.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177478 91177308-0d34-0410-b5e6-96231b3b80d8
This makes DIType's first non-tag parameter the same as DIFile's, allowing them
to both share the common implementation of getFilename/getDirectory in DIScope.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177467 91177308-0d34-0410-b5e6-96231b3b80d8
A node's ordering is only propagated during legalization if (a) the new node does
not have an ordering (is not a CSE'd node), or (b) the new node has an ordering
that is higher than the node being legalized.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177465 91177308-0d34-0410-b5e6-96231b3b80d8
This is another step along the way to making all DIScopes have a common prefix
which can be added to in a general manner to support using directives
(DW_TAG_imported_module).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177462 91177308-0d34-0410-b5e6-96231b3b80d8
Currently, pre-increment store patterns are written to use two separate
operands to represent address base and displacement:
stwu $rS, $ptroff($ptrreg)
This causes problems when implementing the assembler parser, so this
commit changes the patterns to use standard (complex) memory operands
like in all other memory access instruction patterns:
stwu $rS, $dst
To still match those instructions against the appropriate pre_store
SelectionDAG nodes, the patch uses the new feature that allows a Pat
to match multiple DAG operands against a single (complex) instruction
operand.
Approved by Hal Finkel.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177429 91177308-0d34-0410-b5e6-96231b3b80d8
Currently the PPC r0 register is unconditionally reserved. There are two reasons
for this:
1. r0 is treated specially (as the constant 0) by certain instructions, and so
cannot be used with those instructions as a regular register.
2. r0 is used as a temporary register in the CR-register spilling process
(where, under some circumstances, we require two GPRs).
This change addresses the first reason by introducing a restricted register
class (without r0) for use by those instructions that treat r0 specially. These
register classes have a new pseudo-register, ZERO, which represents the r0-as-0
use. This has the side benefit of making the existing target code simpler (and
easier to understand), and will make it clear to the register allocator that
uses of r0 as 0 don't conflict will real uses of the r0 register.
Once the CR spilling code is improved, we'll be able to allocate r0.
Adding these extra register classes, for some reason unclear to me, causes
requests to the target to copy 32-bit registers to 64-bit registers. The
resulting code seems correct (and causes no test-suite failures), and the new
test case covers this new kind of asymmetric copy.
As r0 is still reserved, no functionality change intended.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177423 91177308-0d34-0410-b5e6-96231b3b80d8
Remove an accidentally-added instruction definition and add a comment in the
test case. This is in response to a post-commit review by Bill Schmidt.
No functionality change intended.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177404 91177308-0d34-0410-b5e6-96231b3b80d8
The ARM backend currently has poor codegen for long sext/zext
operations, such as v8i8 -> v8i32. This patch addresses this
by performing a custom expansion in ARMISelLowering. It also
adds/changes the cost of such lowering in ARMTTI.
This partially addresses PR14867.
Patch by Pete Couperus
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177380 91177308-0d34-0410-b5e6-96231b3b80d8
PPC64 supports unaligned loads and stores of 64-bit values, but
in order to use the r+i forms, the offset must be a multiple of 4.
Unfortunately, this cannot always be determined by examining the
immediate itself because it might be available only via a TOC entry.
In order to get around this issue, we additionally predicate the
selection of the r+i form on the alignment of the load or store
(forcing it to be at least 4 in order to select the r+i form).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177338 91177308-0d34-0410-b5e6-96231b3b80d8
Hal Finkel recently added code to allow unaligned memory references
for PowerPC. Two tests were temporarily modified with
-disable-ppc-unaligned to keep them from failing. This patch adjusts
the expected code generation for the unaligned references.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177328 91177308-0d34-0410-b5e6-96231b3b80d8
Apparently my final cleanup to use a relevant suffix for these tests before
committing r176831 caused them to stop running since lit wasn't configured to
run tests with that suffix in those directories (why don't we just have a
global suffix list?). So, add the suffix to the relevant directories & fix the
test that has bitrotted over the last week due to my debug info schema changes.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177315 91177308-0d34-0410-b5e6-96231b3b80d8
This commit fixes an assert that would occur on loops with large constant counts
(like looping for ((uint32_t) -1) iterations on PPC64). The existing code did
not handle counts that it computed to be negative (asserting instead), but
these can be created with valid inputs.
This bug was discovered by bugpoint while I was attempting to isolate a
completely different problem.
Also, in writing test cases for the negative-count problem, I discovered that
the ori/lsi handling was broken (there was a typo which caused the logic that
was supposed to detect these pairs and extract the iteration count to always
fail). This has now also been corrected (and is covered by one of the new test
cases).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177295 91177308-0d34-0410-b5e6-96231b3b80d8
Because the initial-value constants had not been added to the list
of instructions considered for DCE the resulting code had redundant
constant-materialization instructions.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177294 91177308-0d34-0410-b5e6-96231b3b80d8
This is the first step to making all DIScopes have a common metadata prefix (so
that things (using directives, for example) that can appear in any scope can be
added to that common prefix). DIFile is itself a DIScope so the common prefix
of all DIScopes cannot be a DIFile - instead it's the raw filename/directory
name pair.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177239 91177308-0d34-0410-b5e6-96231b3b80d8
This change cleans up two issues with Altivec register spilling:
1. The spilling code was inefficient (using two instructions, and add and a
load, when just one would do)
2. The code assumed that r0 would always be available (true for now, but this
will change)
The new code handles VR spilling just like GPR spills but forced into r+r mode.
As a result, when any VR spills are present, we must now always allocate the
register-scavenger spill slot.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177231 91177308-0d34-0410-b5e6-96231b3b80d8
I was too pessimistic in r177105. Vector selects that fit into a legal register
type lower just fine. I was mislead by the code fragment that I was using. The
stores/loads that I saw in those cases came from lowering the conditional off
an address.
Changing the code fragment to:
%T0_3 = type <8 x i18>
%T1_3 = type <8 x i1>
define void @func_blend3(%T0_3* %loadaddr, %T0_3* %loadaddr2,
%T1_3* %blend, %T0_3* %storeaddr) {
%v0 = load %T0_3* %loadaddr
%v1 = load %T0_3* %loadaddr2
==> FROM:
;%c = load %T1_3* %blend
==> TO:
%c = icmp slt %T0_3 %v0, %v1
==> USE:
%r = select %T1_3 %c, %T0_3 %v0, %T0_3 %v1
store %T0_3 %r, %T0_3* %storeaddr
ret void
}
revealed this mistake.
radar://13403975
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177170 91177308-0d34-0410-b5e6-96231b3b80d8
Unaligned access is supported on PPC for non-vector types, and is generally
more efficient than manually expanding the loads and stores.
A few of the existing test cases were using expanded unaligned loads and stores
to test other features (like load/store with update), and for these test cases,
unaligned access remains disabled.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177160 91177308-0d34-0410-b5e6-96231b3b80d8
In preparation for the addition of other SIMD ISA extensions (such as QPX) we
need to make sure that all Altivec patterns are properly predicated on having
Altivec support.
No functionality change intended (one test case needed to be updated b/c it
assumed that Altivec intrinsics would be supported without enabling Altivec
support).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177152 91177308-0d34-0410-b5e6-96231b3b80d8
For spills into a large stack frame, the FI-elimination code uses the register
scavenger to obtain a free GPR for use with an r+r-addressed load or store.
When there are no available GPRs, the scavenger gets one by using its spill
slot. Previously, we were not always allocating that spill slot and the RS
would assert when the spill slot was needed.
I don't currently have a small test that triggered the assert, but I've
created a small regression test that verifies that the spill slot is now
added when the stack frame is sufficiently large.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177140 91177308-0d34-0410-b5e6-96231b3b80d8
We used to add a spill slot for the register scavenger whenever the function
has a frame pointer. This is unnecessarily conservative: We may need the spill
slot for dynamic stack allocations, and functions with dynamic stack
allocations always have a FP, but we might also have a FP for other reasons
(such as the user explicitly disabling frame-pointer elimination), and we don't
necessarily need a spill slot for those functions.
The structsinregs test needed adjustment because it disables FP elimination.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177106 91177308-0d34-0410-b5e6-96231b3b80d8
By terrible I mean we store/load from the stack.
This matters on PAQp8 in _Z5trainPsS_ii (which is inlined into Mixer::update)
where we decide to vectorize a loop with a VF of 8 resulting in a 25%
degradation on a cortex-a8.
LV: Found an estimated cost of 2 for VF 8 For instruction: icmp slt i32
LV: Found an estimated cost of 2 for VF 8 For instruction: select i1, i32, i32
The bug that tracks the CodeGen part is PR14868.
radar://13403975
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@177105 91177308-0d34-0410-b5e6-96231b3b80d8
In r176898 I updated the cost model to reflect the fact that sext/zext/cast on
v8i32 <-> v8i8 and v16i32 <-> v16i8 are expensive.
This test case is so that we make sure to update the cost model once we fix
CodeGen.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@176955 91177308-0d34-0410-b5e6-96231b3b80d8
This is the next step towards making the metadata for DIScopes have a common
prefix rather than having to delegate based on their tag type.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@176913 91177308-0d34-0410-b5e6-96231b3b80d8
This could be 'null' or the empty string, DIDescriptor::getStringField
coalesces the two cases anyway so it's just a matter of legible/efficient
representation.
The change in behavior of the DICompileUnit::get* functions could be
subsumed by the full verification check - but ideally that should just be an
assertion if we could front-load the actual debug info metadata failure paths.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@176907 91177308-0d34-0410-b5e6-96231b3b80d8
Now that only the register-scavenger version of the CR spilling code remains,
we no longer need the Darwin R2 hack. Darwin can use R0 as a spare register in
any case where the System V ABI uses it (R0 is special architecturally, and so
is reserved under all common ABIs).
A few test cases needed to be updated to reflect the register-allocation changes.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@176868 91177308-0d34-0410-b5e6-96231b3b80d8
These cases were found by further work to remove support for debug info
versioning. Common cleanups (other than changing the version info in the tag
field) included adding the last parameter to compile_units (recently added for
fission support) and other cases of trailing fields in lexical blocks, compile
units, and subprograms.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@176834 91177308-0d34-0410-b5e6-96231b3b80d8
Summary:
Statistics are still available in Release+Asserts (any +Asserts builds),
and stats can also be turned on with LLVM_ENABLE_STATS.
Move some of the FastISel stats that were moved under DEBUG()
back out of DEBUG(), since stats are disabled across the board now.
Many tests depend on grepping "-stats" output. Move those into
a orig_dir/Stats/. so that they can be marked as unsupported
when building without statistics.
Differential Revision: http://llvm-reviews.chandlerc.com/D486
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@176733 91177308-0d34-0410-b5e6-96231b3b80d8
To find the last use of a register unit, start from the bottom and scan
upwards until a user is found.
<rdar://problem/13353090>
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@176706 91177308-0d34-0410-b5e6-96231b3b80d8
fold selectcc (selectcc x, y, a, b, cc), b, a, b, setne ->
selectcc x, y, a, b, cc
Reviewed-by: Christian König <christian.koenig@amd.com>
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@176700 91177308-0d34-0410-b5e6-96231b3b80d8
Two changes:
1. Prefer SET* instructions when possible
2. Handle the CND*_INT case with floating-point args
Reviewed-by: Christian König <christian.koenig@amd.com>
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@176699 91177308-0d34-0410-b5e6-96231b3b80d8