Add pixel format and pixel clock to the list of fields that will initiate a recalculation.
If frame rate is less than 24 or greater than 120 then assume 60Hz.
Consider write-only bits: ATI_CLOCK_STROBE can't be read so clear it.
8 bits at Offset 2 is PLL_DATA. If we don't modify PLL_DATA, then insert the current value of PLL_DATA into the value that will be read from ATI_CLOCK_CNTL.
When checking if a particular byte of a register is accessed, check both the starting position (offset) and ending position (offset + size) of the bytes being access.
- Add BAR 2 decode. This BAR isn't actually used by Mac OS X, but decode it anyway just in case.
- Support updating of BARs (using change_one_bar method).
pixel_format is different than pixel_depth.
pixel_format depends on the GPU. A GPU might have multiple formats for the same depth.
We store this in videoctrl so that we can detect changes in pixel_format like we do for pixel_depth and active_width and active_height.
When fetching DMA command, make sure to convert little endian fields to host endianness (i.e. don't use memcpy).
When fetching DMA command, return the host address of the DMA command for LOAD_QUAD. Maybe this address should be cached whenever this->cmdptr changes?
When fetching DMA command, return whether the DMA command is writable.
For LOAD_QUAD, pass the address of the DMA command to xfer_quad.
Always log unexpected DMA command values.
Write full 32-bit value for LOAD_QUAD.
Write reqCount to resCount.
pci_conv_rd_data can be used to handle unaligned or 64-bit accesses in mmio regions if it's modified to include the next 32-bit value.
For pci config accesses, grackle repeats the 32-bit value. bandit uses a seemingly random number for the next 32-bit value, but we'll make it work like grackle.
PCCard is used by PowerBook G3 Wallstreet in Open Firmware 2.0.1.
CardBus is probed in New World Macs starting from at least Open Firmware 4.1.9f1 sometime after Open Firmware 3.1.1.
- Create PCIBase from common stuff in PCIDevice.
- Add PCIBridgeBase. These have a primary bus number, secondary bus number, and subordinate bus number which are used to determine if PCI type 1 config cycle should be passed.
- Change PCIBridge to use PCIBridgeBase instead of PCIDevice.
- Add PCICardBusBridge which uses PCIBridgeBase.
For example, Old World Macs have versions of Open Firmware that don't support 512 MB BARs correctly. They may attempt to set such a BAR to 0x90000000 (a 256 MB boundary) instead of 0xA0000000 (the next available 512 MB boundary).
So that you don't see identical messages "Could not restore NVRAM content from the given file."
Instead, one will mention nvram.bin and the other will mention pram.bin.
- Add mask so that hardware cursor cannot be drawn beyond the right edge of the frame buffer.
- Add invert pixels. Invert pixels are used in the I-beam cursor and the Watch cursor.
- Fix video vram endianness. It should behave like RAM.
- Add read for registers ENABLE, INT_STATUS, INT_ENABLE.
- Add write for registers CNTTST, INT_ENABLE.
- Add support for 16bpp and 32bpp.
- Add vbl interrupt.
Cherrypicks a small piece of joevt/dingusppc@117ca1e449
so that booting from the 10.2 CD gets past it trying to change the video
mode to 15bpp.
Co-authored-by: joevt <joevt@shaw.ca>
AdbKeyboard would copy the event into its own fields and set the
changed field, so that we could return the event when register was 0.
However, if a subsequent event was received before ADB polling, the
previous event would be overwritten and lost.
Fix this by maintaining a queue of events, so that we can return
everything since the last poll.
We were using an empty value on the second byte of the ADB keyboard
register 0, but that maps to the "a" key. This manifested itself
as the Key Caps DA never showing the "a" key as being down.
Switch to a non-existent key for the second byte.
Allows different implementations for different platforms (the JS
build relies on browser APIs to stream disk images over the network).
Setting aside the JS build, this also reduces some code duplication.
Besides generating KeyboardEvents in the SDL event handler and
returning the key state in the register 0 reads of the AdbKeyboard
device, we also needed to generalize the ADB bus polling a bit. We now
check all devices that have the service request bit set, instead of
hardcoding the mouse.
The SDL key event -> ADB raw key code mapping is based on BasiliskII/
SheepShaver's, but cleaned up a bit.
Otherwise if pull_data is called again, it will think that it still
has data available in the buffer (rem_len will be non-zero) and
random data at the buffer location will be returned.
This manifested itself as noise being played back in the JS
implementation of the SoundServer. The cubeb implementation was not
affected because it stops polling once it's told it has no more
data in the buffer. Both approaches are valid (the JS version pads
data with silence), and the DMA buffer should support both.
Result of running IWYU (https://include-what-you-use.org/) and
applying most of the suggestions about unncessary includes and
forward declarations.
Was motivated by observing that <thread> was being included in
ppcopcodes.cpp even though it was unused (found while researching
the use of threads), but seems generally good to help with build
times and correctness.
While Emscripten has an SDL compabtility layer, it assumes that the
code is executing in the main browser process (and thus has access to
them DOM). The Infinite Mac project runs emulators in a worker thread
(for better performance) and has a custom API for the display, sound,
input, etc. Similarly, it does not need the cross-platform sound support
from cubeb, there there is a sound API as well.
This commit makes SDL (*_sdl.cpp) and cubeb-based (*_cubeb.cpp) code be
skipped when targeting Emscripten, and instead *_js.cpp files are used
instead (this is the cross-platform convention used by Chromium[^1], and
could be extended for other targets).
For hostevents.cpp and soundserver.cpp the entire file was replaced,
whereas for videoctrl.cpp there was enough shared logic that it was
kept, and the platform-specific bits were moved behind a Display class
that can have per-platform implementations. For cases where we need
additional private fields in the platform-specific classes, we use
a PIMPL pattern.
The *_js.cpp files with implementations are not included in this
commit, since they are closely tied to the Infinite Mac project, and
will live in its fork of DingusPPC.
[^1]: https://www.chromium.org/developers/design-documents/conventions-and-patterns-for-multi-platform-development/
The simplest solution is to cut the aperture size by the amount
of video RAM installed. This way, accesses to the big-endian
aperture located above the installed VRAM will be catched and
reported by the MMU.
The disk cache is unchanged. data_ptr continues to be only used for the user data sector area for each block. The other sector areas (synch, header, etc.) are filled in while reading.
has_data and get_data exist as a way to bypass data_ptr for parts of the transfer outside the user data sector area of each block. The default behaviour is defined in atabasedevice and is overridden by atapicdrom for the Read CD command. atapicdrom has a flag doing_sector_areas to control the behavior of the get_data method. When the flag is true, the sector_areas, current_block, and current_block_byte are used for selecting the correct data from one of the sector areas. The Read CD command initializes those variables. xfer_cnt remains the total number of bytes to be transferred and is now not necessarily the same as the number of disk image blocks read into the disk cache.
lba_to_msf is used to fill in the header. The values was not verified using a real CD.
Mac OS X just cares about the Mode in the header. For now, only the synch and header and user data areas are filled in. The other areas read as all zeros.
In Read TOC format 2, Mac OS X passes zero for Session Number. I believe Read TOC is supposed to return the first session starting from that number so it should return info for Session 1 as it would if Mac OS X passed 1 for the Session Number.
It was possible to corrupt New World nvram using dingusppc setenv command.
- setenv must call get_config_vars to set data_length so that it can calculate free space.
- data_length represents the number of bytes taken by nvram variables including the terminating null for the value (name, '=', value, '\0'). Previously, it did not include the terminating null.
- The list of variables and values ends at a '\0' or at pos == 4096 bytes. Previously, data_length wouldn't get set if pos >= 4096.
- Allow setenv to create new nvram variables.
- Since data_length now represents the total number of used bytes, free_space now represents the actual free space, so use > free_space (instead of >= free_space) to determine insufficient space.
- While parsing nvram variable name, do not read beyond 4096 bytes.
- Use a different error message for each problem that can occur while parsing nvram variable name.
If a nvram variable has CRLF or CR, replace them with LF so each line appears on a new line in the console output.
Also, add indent to each line so that each line appears only in the value column and not in the name column.
For some reason, on Windows, whether it be VS2022 or Clang, it will crash when trying to write to a Big Mac register if you don't specify the exact name of the component within Heathrow.
This commit fixes that.
- Added an overloaded version of attach_pci_device which takes a suffix string that can be used to make a device name unique so that multiple devices of the same class can be added to a machine. The method returns a PCIDevice which can be easily used to attach more PCI devices if it is a PCIHost.
PCIDevice
- supports_io_space method now uses a flag has_io_space which is automatically set for PCI bridges or PCI devices that have an I/O BAR.
atirage
- Devices that have I/O BARs don't need a supports_io_space method.
mpc106
- Devices that don't have I/O methods don't need a supports_io_space method.
A multi-function device may have functions of the same class (e.g. a USB device with two OHCI functions) but each function should be initialized with a different interrupt pin.
Add PCI bridge and multi-function device support.
Overview:
- A multi-function device is two or more PCIDevices with the same device number but one device is function zero (as with currently implemented PCIDevices) and the other functions have function numbers between 1 and 7. The device number and function number are properties of the PCIDevice's parent PCIHost connection.
- A PCIBridge is a PCIHost (it can connect child PCI devices) and a PCIDevice (it has config space, BARs, and expansion ROM).
- A PCIDevice has Type 0 header. It has 6 BARs.
- A PCIBridge has Type 1 header. It has 2 BARs. The config space registers beginning from offset 0x18 differ from those of a PCIDevice.
Possible future modifications:
- Add a PCICardBus class. It is a PCIHost. It has Type 2 header. It has one BAR. The first 20 bytes match Type 0 and Type 1 headers. These exist in New World Macs. They allow hot-plug of PCI devices.
- Split base PCI registers (first 16 bytes) into a PCIBase class. Type 1 and 2 have two or one BAR but I think all 6 BARs belong in PCIBase class anyway.
- Split PCIHost into two classes: Currently existing PCIHosts (Bandit, Grackle) are PCIHost and PCIRoot (they have the broadcast I/O requests functionality) while PCIBridge is PCIHost only - it can propagate I/O requests but does not originate the broadcast.
- pci_register_mmio_region should maybe return a pointer to a region struct so that it can be used for unregistering or modifying the region's range. This may be useful for PCI bridges which have ranges that may constrain memory BARs of their downstream devices.
PCIDevice
- Moved expansion ROM BAR handling to a separate function pci_wr_exp_rom_bar so that it can be used by both PCI devices and PCI bridges which have the ROM BAR in different locations. It now supports unmapping expansion ROM. Also made exp_rom_bar not writable if there's no ROM.
- Added num_bars field which specifies the number of valid BARs since Type 0, 1, and 2 headers have different number of BARs.
- map_exp_rom_mem now properly unmaps expansion ROM (using new function unmap_exp_rom_mem) before mapping it again.
- Added function set_multi_function which modifies hdr_type to indicate if a device has other functions. This is to be applied only to devices with function number 0.
PCIHost
- When attaching a PCI device, it will check if it's a multi-function device (there exists an attached function that is not zero) and adjust hdr_type of function 0 of the device accordingly.
- Attached PCI bridges are added to a list of PCI bridges attached to the host.
- Added pci_io_read_loop and pci_io_write_loop which loop through attached PCI devices to find one that will perform the action for the given I/O address without logging an error (since some other device might perform the action).
- Added pci_io_read_broadcast and pci_io_write_broadcast which are used by a PCI root (bandit/grackle). They will log an error if the action is not performed. They should probably do a machine check exception to match real Power Macs.
- pci_find_device (used by PCI root) will recursively find a PCIDevice for type 1 config register accesses.
- Logging from PCIHost now includes the name of the PCIHost instead of just "PCIHost" because there can be multiple PCI hosts.
PCIBridge
- Sets num_bars to 2 and hdr_type to 1.
- I/O ranges set in the config registers are handled correctly by pci_io_read and pci_io_write.
- Memory ranges set in the config registers do not currently affect memory mmio regions. It is assumed that Open Firmware and the OS will set the ranges and BARs correctly to allow all BARs to be accessed fully.
bandit, mpc106
- Bandit and Grackle now call pci_io_read_broadcast and pci_io_read_broadcast to pass I/O accesses to downstream PCI devices.
- Chaos is modified to work like Bandit even though it will never have PCI bridges attached or devices that support I/O accesses. It's simpler this way.
PCIHost
- PCIHosts (bandit and grackle) now use device number and function number for identifying attached PCIDevices. A macro DEV_FUN is added to calculate this new slot_id. Bandit no longer uses IDSEL. Grackle no longer uses only device number.
machinecatalyst, machinegossamer, machinetnt
- Use DEV_FUN to attach PCI devices by device number and function number.
- Don't log anything if the I/O access is not for this device. A different device might handle it.
- Don't return true for I/O access if an I/O access is not performed. Otherwise the I/O access won't be passed to other devices.
While dingusppc only emulates 32-bit Macs (for now), it is possible for a 32-bit Power Mac to use a PCIe card that has 64-bit BARs.
finish_config_bars is added to scan the cfg values of the BARs and determine their type. The type is stored separately so that it does not need to be determined again.
The type can be I/O (16 or 32 bit) or Mem (20 or 32 or 64 bit). A 64 bit bar is two BARs, the second contains the most significant 32 bits.
set_bar_value uses the stored type instead of trying to determine the type itself. It is always called even when the firmware is doing sizing. For sizing, It does the job of setting the bar value so do_bar_sizing is now just a stub.
Every PCIDevice that has a BAR needs to call finish_config_bars after setting up the cfg values just as they need to setup the cfg values. Since they need to do both, maybe the cfg values should be arguments of finish_config_bars, then finish_config_bars() should be renamed config_bars().
