memcpy's like:
memcpy(A, B)
memcpy(A, C)
we cannot delete the first memcpy as dead if A and C might be aliases.
If so, we actually get:
memcpy(A, B)
memcpy(A, A)
which is not correct to transform into:
memcpy(A, A)
This patch was heavily influenced by Jakub Staszak's patch in PR8728, thanks
Jakub!
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120974 91177308-0d34-0410-b5e6-96231b3b80d8
difficult on current ARM implementations for a few reasons.
1. Even though a single vmla has latency that is one cycle shorter than a pair
of vmul + vadd, a RAW hazard during the first (4? on Cortex-a8) can cause
additional pipeline stall. So it's frequently better to single codegen
vmul + vadd.
2. A vmla folowed by a vmul, vmadd, or vsub causes the second fp instruction to
stall for 4 cycles. We need to schedule them apart.
3. A vmla followed vmla is a special case. Obvious issuing back to back RAW
vmla + vmla is very bad. But this isn't ideal either:
vmul
vadd
vmla
Instead, we want to expand the second vmla:
vmla
vmul
vadd
Even with the 4 cycle vmul stall, the second sequence is still 2 cycles
faster.
Up to now, isel simply avoid codegen'ing fp vmla / vmls. This works well enough
but it isn't the optimial solution. This patch attempts to make it possible to
use vmla / vmls in cases where it is profitable.
A. Add missing isel predicates which cause vmla to be codegen'ed.
B. Make sure the fmul in (fadd (fmul)) has a single use. We don't want to
compute a fmul and a fmla.
C. Add additional isel checks for vmla, avoid cases where vmla is feeding into
fp instructions (except for the #3 exceptional case).
D. Add ARM hazard recognizer to model the vmla / vmls hazards.
E. Add a special pre-regalloc case to expand vmla / vmls when it's likely the
vmla / vmls will trigger one of the special hazards.
Work in progress, only A+B are enabled.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120960 91177308-0d34-0410-b5e6-96231b3b80d8
Also add asserts that the indices are valid in InsertValueInst::init(). ExtractValueInst already asserts when constructed with invalid indices.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120956 91177308-0d34-0410-b5e6-96231b3b80d8
result. This allows us to compile:
void *test12(long count) {
return new int[count];
}
into:
test12:
movl $4, %ecx
movq %rdi, %rax
mulq %rcx
movq $-1, %rdi
cmovnoq %rax, %rdi
jmp __Znam ## TAILCALL
instead of:
test12:
movl $4, %ecx
movq %rdi, %rax
mulq %rcx
seto %cl
testb %cl, %cl
movq $-1, %rdi
cmoveq %rax, %rdi
jmp __Znam
Of course it would be even better if the regalloc inverted the cmov to 'cmovoq',
which would eliminate the need for the 'movq %rdi, %rax'.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120936 91177308-0d34-0410-b5e6-96231b3b80d8
backend that they were all implemented except umul. This one fell back
to the default implementation that did a hi/lo multiply and compared the
top. Fix this to check the overflow flag that the 'mul' instruction
sets, so we can avoid an explicit test. Now we compile:
void *func(long count) {
return new int[count];
}
into:
__Z4funcl: ## @_Z4funcl
movl $4, %ecx ## encoding: [0xb9,0x04,0x00,0x00,0x00]
movq %rdi, %rax ## encoding: [0x48,0x89,0xf8]
mulq %rcx ## encoding: [0x48,0xf7,0xe1]
seto %cl ## encoding: [0x0f,0x90,0xc1]
testb %cl, %cl ## encoding: [0x84,0xc9]
movq $-1, %rdi ## encoding: [0x48,0xc7,0xc7,0xff,0xff,0xff,0xff]
cmoveq %rax, %rdi ## encoding: [0x48,0x0f,0x44,0xf8]
jmp __Znam ## TAILCALL
instead of:
__Z4funcl: ## @_Z4funcl
movl $4, %ecx ## encoding: [0xb9,0x04,0x00,0x00,0x00]
movq %rdi, %rax ## encoding: [0x48,0x89,0xf8]
mulq %rcx ## encoding: [0x48,0xf7,0xe1]
testq %rdx, %rdx ## encoding: [0x48,0x85,0xd2]
movq $-1, %rdi ## encoding: [0x48,0xc7,0xc7,0xff,0xff,0xff,0xff]
cmoveq %rax, %rdi ## encoding: [0x48,0x0f,0x44,0xf8]
jmp __Znam ## TAILCALL
Other than the silly seto+test, this is using the o bit directly, so it's going in the right
direction.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120935 91177308-0d34-0410-b5e6-96231b3b80d8
- Also adds a new POPCNT subtarget feature that is currently enabled if the target
supports SSE4.2 (nehalem) or SSE4A (barcelona).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120917 91177308-0d34-0410-b5e6-96231b3b80d8
foo = a - b
.long foo
instead of just
.long a - b
First, on darwin9 64 bits the assembler produces the wrong result. Second,
if "a" is the end of the section all darwin assemblers (9, 10 and mc) will not
consider a - b to be a constant but will if the dummy foo is created.
Split how we handle these cases. The first one is something MC should take care
of. The second one has to be handled by the caller.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120889 91177308-0d34-0410-b5e6-96231b3b80d8
doing that if the target is darwin10 or newer.
This fixes
*) Direct object emission was producing objects without the workaround on
darwin9.
*) Assembly printing was producing objects with the workaround on linux.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120866 91177308-0d34-0410-b5e6-96231b3b80d8
named the same, so it had to qualify type names according to the enclosing
scope to ensure uniqueness. This is no longer needed for correctness (though
it may be helpful when reading the IR), so this test has lost its importance.
Zap it because dragonegg will never be able to produce the qualified type name
since modern gcc zaps language specific info (such as whether a type is nested
inside another - needed to get X::Y here) before dragonegg is reached.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120721 91177308-0d34-0410-b5e6-96231b3b80d8
Lifted adjustFixupValue() from Darwin for sharing w ELF.
Test added
TODO:
refactor ELFObjectWriter::RecordRelocation more.
Possibly share more code with Darwin?
Lots more relocations...
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120534 91177308-0d34-0410-b5e6-96231b3b80d8
20040709-1.c from the gcc testsuite. I was using the size of a
pointer instead of the pointee. This fixes rdar://8713376
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120519 91177308-0d34-0410-b5e6-96231b3b80d8
legalization time. Since at legalization time there is no mapping from
SDNode back to the corresponding LLVM instruction and the return
SDNode is target specific, this requires a target hook to check for
eligibility. Only x86 and ARM support this form of sibcall optimization
right now.
rdar://8707777
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120501 91177308-0d34-0410-b5e6-96231b3b80d8
may-aliasing stores that partially overlap with different base
pointers. This implements PR6043 and the non-variable part of
PR8657
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120485 91177308-0d34-0410-b5e6-96231b3b80d8
now that DSE hacks on them. This fixes a regression I introduced,
by generalizing DSE to hack on transfers.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120445 91177308-0d34-0410-b5e6-96231b3b80d8
certainly be made more generic. But it does allow us to parse something like:
ldr r3, [r2, r4]
correctly in Thumb mode.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120408 91177308-0d34-0410-b5e6-96231b3b80d8
about pairs of AA::Location's instead of looking for MemDep's
"Def" predicate. This is more powerful and general, handling
memset/memcpy/store all uniformly, and implementing PR8701 and
probably obsoleting parts of memcpyoptimizer.
This also fixes an obscure bug with init.trampoline and i8
stores, but I'm not surprised it hasn't been hit yet. Enhancing
init.trampoline to carry the size that it stores would allow
DSE to be much more aggressive about optimizing them.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120406 91177308-0d34-0410-b5e6-96231b3b80d8
contains "ref".
Enhance DSE to use a modref query instead of a store-specific hack
to generalize the "ignore may-alias stores" optimization to handle
memset and memcpy.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120368 91177308-0d34-0410-b5e6-96231b3b80d8
instructions. I choose to handle this with an asmparser hack,
though it could be handled by changing all the instruction definitions
to allow be "setneb" instead of "setne". The asm parser hack is
better in this case, because we want the disassembler to produce
setne, not setneb.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120260 91177308-0d34-0410-b5e6-96231b3b80d8
Unittests need LLVM_BUILD_MODE to pick up each test.
Confirmed on CentOS5, Mingw, MSYS, and with possible configurations on VS8 and VS10.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120212 91177308-0d34-0410-b5e6-96231b3b80d8
automatically. Use -S with llvm-gcc rather than -c, so tests can
work when llvm-gcc is really dragonegg (which can output IR with -S
but not -c). Yes, dragonegg supports objective-c++ (poorly though).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120164 91177308-0d34-0410-b5e6-96231b3b80d8
automatically. Use -S with llvm-gcc rather than -c, so tests can
work when llvm-gcc is really dragonegg (which can output IR with -S
but not -c). Yes, dragonegg supports objective-c (poorly though).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120163 91177308-0d34-0410-b5e6-96231b3b80d8
automatically. Use -S with llvm-gcc rather than -c, so tests can
work when llvm-gcc is really dragonegg (which can output IR with -S
but not -c).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120160 91177308-0d34-0410-b5e6-96231b3b80d8
the output of this test. Since it was producing bitcode, that clearly
wasn't happening! Have it produce target assembler and assemble that
instead.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120159 91177308-0d34-0410-b5e6-96231b3b80d8
automatically. Use -S with llvm-gcc rather than -c, so tests can
work when llvm-gcc is really dragonegg (which can output IR with -S
but not -c).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120158 91177308-0d34-0410-b5e6-96231b3b80d8
We need to check if the individual vector elements are sign/zero-extended
values. For now this only handles constants values. Radar 8687140.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120034 91177308-0d34-0410-b5e6-96231b3b80d8
fairly systematic way in instcombine. Some of these cases were already dealt
with, in which case I removed the existing code. The case of Add has a bunch of
funky logic which covers some of this plus a few variants (considers shifts to be
a form of multiplication), which I didn't touch. The simplification performed is:
A*B+A*C -> A*(B+C). The improvement is to do this in cases that were not already
handled [such as A*B-A*C -> A*(B-C), which was reported on the mailing list], and
also to do it more often by not checking for "only one use" if "B+C" simplifies.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@120024 91177308-0d34-0410-b5e6-96231b3b80d8
state. Previously Thumb2 would restore sp from fp like this:
mov sp, r7
sub, sp, #4
If an interrupt is taken after the 'mov' but before the 'sub', callee-saved
registers might be clobbered by the interrupt handler. Instead, try
restoring directly from sp:
add sp, #4
Or, if necessary (with VLA, etc.) use a scratch register to compute sp and
then restore it:
sub.w r4, r7, #8
mov sp, r7
rdar://8465407
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119977 91177308-0d34-0410-b5e6-96231b3b80d8
folding improvements: if P points to a type of size zero, turn "gep P, N" into "P".
More generally, if a gep index type has size zero, instcombine could replace the
index with zero, but that is not done here.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119942 91177308-0d34-0410-b5e6-96231b3b80d8
void a(int x) { if (((1<<x)&8)==0) b(); }
into "x != 3", which occurs over 100 times in 403.gcc but in no
other program in llvm-test.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119922 91177308-0d34-0410-b5e6-96231b3b80d8
allowing the memcpy to be eliminated.
Unfortunately, the requirements on byval's without explicit
alignment are really weak and impossible to predict in the
mid-level optimizer, so this doesn't kick in much with current
frontends. The fix is to change clang to set alignment on all
byval arguments.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119916 91177308-0d34-0410-b5e6-96231b3b80d8
DAGCombine from making an illegal transformation of bitcast of a scalar to a
vector into a scalar_to_vector.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119819 91177308-0d34-0410-b5e6-96231b3b80d8
lr" instruction cannot be tested just yet. It requires matching a "condition
code", but adding one of those makes things go south quickly...
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119774 91177308-0d34-0410-b5e6-96231b3b80d8
if the extension types were not the same. The result was that if you
fed a select with sext and zext loads, as in the testcase, then it
would get turned into a zext (or sext) of the select, which is wrong
in the cases when it should have been an sext (resp. zext). Reported
and diagnosed by Sebastien Deldon.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119728 91177308-0d34-0410-b5e6-96231b3b80d8
preserves LCSSA form out of ScalarEvolution and into the LoopInfo
class. Use it to check that SimplifyInstruction simplifications
are not breaking LCSSA form. Fixes PR8622.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119727 91177308-0d34-0410-b5e6-96231b3b80d8
Remove movePastCSLoadStoreOps and associated code for simple pointer
increments. Update routines that depended upon other opcodes for save/restore.
Adjust all testcases accordingly.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119725 91177308-0d34-0410-b5e6-96231b3b80d8
this was a tree of hashtables, and a query recursed into the table for the immediate dominator ad infinitum
if the initial lookup failed. This led to really bad performance on tall, narrow CFGs.
We can instead replace it with what is conceptually a multimap of value numbers to leaders (actually
represented by a hashtable with a list of Value*'s as the value type), and then
determine which leader from that set to use very cheaply thanks to the DFS numberings maintained by
DominatorTree. Because there are typically few duplicates of a given value, this scan tends to be
quite fast. Additionally, we use a custom linked list and BumpPtr allocation to avoid any unnecessary
allocation in representing the value-side of the multimap.
This change brings with it a 15% (!) improvement in the total running time of GVN on 403.gcc, which I
think is pretty good considering that includes all the "real work" being done by MemDep as well.
The one downside to this approach is that we can no longer use GVN to perform simple conditional progation,
but that seems like an acceptable loss since we now have LVI and CorrelatedValuePropagation to pick up
the slack. If you see conditional propagation that's not happening, please file bugs against LVI or CVP.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119714 91177308-0d34-0410-b5e6-96231b3b80d8
refusing to optimize two memcpy's like this:
copy A <- B
copy C <- A
if it couldn't prove that noalias(B,C). We can eliminate
the copy by producing a memmove instead of memcpy.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119694 91177308-0d34-0410-b5e6-96231b3b80d8
if it is passed as a byval argument. The byval argument will just be a
read, so it is safe to read from the original global instead. This allows
us to promote away the %agg.tmp alloca in PR8582
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119686 91177308-0d34-0410-b5e6-96231b3b80d8
and testing is easier. A good example is the unknown-location.ll test that
now can just look for ".loc 1 0 0". We also don't use a DW_LNE_set_address for
every address change anymore.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119613 91177308-0d34-0410-b5e6-96231b3b80d8
memset; we may need it to decide between MOVAPS and MOVUPS
later. Adjust a test that was looking for wrong code.
PR 3866 / 8675131.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119605 91177308-0d34-0410-b5e6-96231b3b80d8
appear to differ on Linux. Try to make them pass on Linux.
Would be good for a Linux person to review this.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119572 91177308-0d34-0410-b5e6-96231b3b80d8
It is generally not sufficient to check if the starting offset is in range
of the maximum offset that can be efficiently used for the target.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119565 91177308-0d34-0410-b5e6-96231b3b80d8
This makes it more clear that the symbol is an internal, compiler-generated
name and gives a little more description about its contents.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119564 91177308-0d34-0410-b5e6-96231b3b80d8
It was mistakenly looking at the pointer type when checking for the size of
global variables. This is a partial fix for Radar 8673120.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119563 91177308-0d34-0410-b5e6-96231b3b80d8
and xor. The 32-bit move immediates can be hoisted out of loops by machine
LICM but the isel hacks were preventing them.
Instead, let peephole optimization pass recognize registers that are defined by
immediates and the ARM target hook will fold the immediates in.
Other changes include 1) do not fold and / xor into cmp to isel TST / TEQ
instructions if there are multiple uses. This happens when the 'and' is live
out, machine sink would have sinked the computation and that ends up pessimizing
code. The peephole pass would recognize situations where the 'and' can be
toggled to define CPSR and eliminate the comparison anyway.
2) Move peephole pass to after machine LICM, sink, and CSE to avoid blocking
important optimizations.
rdar://8663787, rdar://8241368
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119548 91177308-0d34-0410-b5e6-96231b3b80d8
instructions have to distinguish between lists of single- and double-precision
registers in order for the ASM matcher to do a proper job. In all other
respects, a list of single- or double-precision registers are the same as a list
of GPR registers.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119460 91177308-0d34-0410-b5e6-96231b3b80d8
over a phi node by applying it to each operand may be wrong if the
operation and the phi node are mutually interdependent (the testcase
has a simple example of this). So only do this transform if it would
be correct to perform the operation in each predecessor of the block
containing the phi, i.e. if the other operands all dominate the phi.
This should fix the FFMPEG snow.c regression reported by İsmail Dönmez.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119347 91177308-0d34-0410-b5e6-96231b3b80d8
The live range of a register defined by an early clobber starts at the use slot,
not the def slot.
Except when it is an early clobber tied to a use operand. Then it starts at the
def slot like a standard def.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119305 91177308-0d34-0410-b5e6-96231b3b80d8
live ranges for the spill register are also defined at the use slot instead of
the normal def slot.
This fixes PR8612 for the inline spiller. A use was being allocated to the same
register as a spilled early clobber def.
This problem exists in all the spillers. A fix for the standard spiller is
forthcoming.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119182 91177308-0d34-0410-b5e6-96231b3b80d8
variable if recursing fails to simplify it.
Factor AliasedSymbol to be a method of MCSymbol.
Update MCAssembler::EvaluateFixup to match the change in
EvaluateAsRelocatableImpl.
Remove the WeakRefExpr hack, as the object writer now sees the weakref with
no extra effort needed.
Nothing else is using MCTargetExpr, but keep it for now.
Now that the ELF writer sees relocations with aliases, handle
.weak foo2
foo2:
.weak bar2
.set bar2,foo2
.quad bar2
the same way gas does and produce a relocation with bar2.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119152 91177308-0d34-0410-b5e6-96231b3b80d8
This moves most of the isUsed logic to the MCSymbol itself. With this we
get a bit more relaxed about allowing definitions after uses: uses that
don't evaluate their argument immediately (jmp foo) are accepted.
ddunbar, this was the smallest compromise I could think of that lets us
accept gcc (and clang!) assembly.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119144 91177308-0d34-0410-b5e6-96231b3b80d8
offload the work to hasConstantValue rather than do something more
complicated (such handling mutually recursive phis) because (1) it is
not clear it is worth it; and (2) if it is worth it, maybe such logic
would be better placed in hasConstantValue. Adjust some GVN tests
which are now cleaned up much further (eg: all phi nodes are removed).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119043 91177308-0d34-0410-b5e6-96231b3b80d8
SimplifyAssociativeOrCommutative) "(A op C1) op C2" -> "A op (C1 op C2)",
which previously was only done if C1 and C2 were constants, to occur whenever
"C1 op C2" simplifies (a la InstructionSimplify). Since the simplifying operand
combination can no longer be assumed to be the right-hand terms, consider all of
the possible permutations. When compiling "gcc as one big file", transform 2
(i.e. using right-hand operands) fires about 4000 times but it has to be said
that most of the time the simplifying operands are both constants. Transforms
3, 4 and 5 each fired once. Transform 6, which is an existing transform that
I didn't change, never fired. With this change, the testcase is now optimized
perfectly with one run of instcombine (previously it required instcombine +
reassociate + instcombine, and it may just have been luck that this worked).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@119002 91177308-0d34-0410-b5e6-96231b3b80d8
darwin and, judging from the buildbots, Linux.
Removing it for now, but this is not the right fix,
Wesley please look at it.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118977 91177308-0d34-0410-b5e6-96231b3b80d8
2. Fixing several errors in disassembler uncovered by test cases.
3. Fixing invalid encoding of PCMPEQ and PCMPNE uncovered by test cases.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118969 91177308-0d34-0410-b5e6-96231b3b80d8
2. Parsing .word directive in MBlaze asm parser
3. Fixing hack where memory instructions reversed order of last two parameters
4. Fixing many improperly encoded instructions
5. Support parsing special instructions (MFS,MTS,etc.)
6. Removing unused functions from inst printer
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118941 91177308-0d34-0410-b5e6-96231b3b80d8
support for the case where alignment<value size.
These cases were silently miscompiled before this patch.
Now they are overly verbose -especially storing is- and
any front-end should still avoid misaligned memory
accesses as much as possible. The bit juggling algorithm
added here probably has some room for improvement still.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118889 91177308-0d34-0410-b5e6-96231b3b80d8
Fix minimum 16-bit signed value error exposed by MC asm parser tests
Add initial MC asm parser tests for the MBlaze backend
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118844 91177308-0d34-0410-b5e6-96231b3b80d8
testing for dereferenceable pointers into a helper function,
isDereferenceablePointer. Teach it how to reason about GEPs
with simple non-zero indices.
Also eliminate ArgumentPromtion's IsAlwaysValidPointer,
which didn't check for weak externals or out of range gep
indices.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118840 91177308-0d34-0410-b5e6-96231b3b80d8
references. For example, this allows gvn to eliminate the load in
this example:
void foo(int n, int* p, int *q) {
p[0] = 0;
p[1] = 1;
if (n) {
*q = p[0];
}
}
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118714 91177308-0d34-0410-b5e6-96231b3b80d8
nodes can be used in loops, this could result in infinite looping
if there is no recursion limit, so add such a limit. It is also
used for the SelectInst case because in theory there could be an
infinite loop there too if the basic block is unreachable.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118694 91177308-0d34-0410-b5e6-96231b3b80d8
It is only supported for ARM code. Normally Thumb2 code would use DMB instead,
but depending on how the compiler is invoked (e.g., -mattr=-db) that might be
disabled. This prevents a "cannot select MEMBARRIER_MCR" error in that
situation. Radar 8644195
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118642 91177308-0d34-0410-b5e6-96231b3b80d8
to optionally look for constant or local (alloca) memory.
Teach BasicAliasAnalysis::pointsToConstantMemory to look through Select
and Phi nodes, and to support looking for local memory.
Remove FunctionAttrs' PointsToLocalOrConstantMemory function, now that
AliasAnalysis knows all the tricks that it knew.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118412 91177308-0d34-0410-b5e6-96231b3b80d8
of a select instruction, see if doing the compare with the
true and false values of the select gives the same result.
If so, that can be used as the value of the comparison.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118378 91177308-0d34-0410-b5e6-96231b3b80d8
different forms of this instruction (movw/movl/movq) which we reported
as being ambiguous. Since they all do the same thing, gas just picks the
one with the shortest encoding. Follow its lead here.
This implements rdar://8208615
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118362 91177308-0d34-0410-b5e6-96231b3b80d8
exposed:
GAS doesn't accept "fcomip %st(1)", it requires "fcomip %st(1), %st(0)"
even though st(0) is implicit in all other fp stack instructions.
Fortunately, there is an alias for fcomip named "fcompi" and gas does
accept the default argument for the alias (boggle!).
As such, switch the canonical form of this instruction to "pi" instead
of "ip". This makes the code generator and disassembler generate pi,
avoiding the gas bug.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118356 91177308-0d34-0410-b5e6-96231b3b80d8
shift-by-1 instructions, where the asmstring doesn't contain
the implicit 1. It turns out that a bunch of these rotate
instructions were completely broken because they used 1
instead of $1.
This fixes assembly mismatches on "rclb $1, %bl" and friends,
where we used to generate the 3 byte form, we now generate the
proper 2-byte form.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118355 91177308-0d34-0410-b5e6-96231b3b80d8
floating point stack instructions instead of looking for b/w/l/q.
This fixes issues where we'd accidentally match fistp to fistpl,
when it is in fact an ambiguous instruction.
This changes the behavior of llvm-mc to reject fstp, which was the
correct fix for rdar://8456389:
t.s:1:1: error: ambiguous instructions require an explicit suffix (could be 'fstps', 'fstpl', or 'fstpt')
fstp (%rax)
it also causes us to correctly reject fistp and fist, which addresses
PR8528:
t.s:2:1: error: ambiguous instructions require an explicit suffix (could be 'fistps', or 'fistpl')
fistp (%rax)
^
t.s:3:1: error: ambiguous instructions require an explicit suffix (could be 'fists', or 'fistl')
fist (%rax)
^
Thanks to Ismail Donmez for tracking down the issue here!
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118346 91177308-0d34-0410-b5e6-96231b3b80d8
sequence of loads and stores was being generated to perform the
copy on the x86 targets if the parameter was less than 4 byte
aligned, causing llc to use up vast amounts of memory and time.
Use a "rep movs" form instead. PR7170.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118260 91177308-0d34-0410-b5e6-96231b3b80d8
We could be more aggressive about making this work for a larger range of constants,
but this seems like a good start.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118201 91177308-0d34-0410-b5e6-96231b3b80d8
all of the different element sizes are pseudo instructions that map down to vext.8 underneath, with
the immediate shifted left to reflect the increased element size.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118183 91177308-0d34-0410-b5e6-96231b3b80d8
vldr.64 d1, [r0, #-32]
The problem was with how the addressing mode 5 encodes the offsets. This change
makes sure that the way offsets are handled in addressing mode 5 is consistent
throughout the MC code. It involves re-refactoring the "getAddrModeImmOpValue"
method into an "Imm12" and "addressing mode 5" version. But not to worry! The
majority of the duplicated code has been unified.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118144 91177308-0d34-0410-b5e6-96231b3b80d8
1. Fix pre-ra scheduler so it doesn't try to push instructions above calls to
"optimize for latency". Call instructions don't have the right latency and
this is more likely to use introduce spills.
2. Fix if-converter cost function. For ARM, it should use instruction latencies,
not # of micro-ops since multi-latency instructions is completely executed
even when the predicate is false. Also, some instruction will be "slower"
when they are predicated due to the register def becoming implicit input.
rdar://8598427
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118135 91177308-0d34-0410-b5e6-96231b3b80d8
with immediates up to 16-bits in size. The same logic is applied to other LDR
encodings, e.g. VLDR, but which use a different immediate bit width (8-bits in
VLDR's case). Removing the "12" allows it to be more generic.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@118094 91177308-0d34-0410-b5e6-96231b3b80d8
at more than those which define CPSR. You can have this situation:
(1) subs ...
(2) sub r6, r5, r4
(3) movge ...
(4) cmp r6, 0
(5) movge ...
We cannot convert (2) to "subs" because (3) is using the CPSR set by
(1). There's an analogous situation here:
(1) sub r1, r2, r3
(2) sub r4, r5, r6
(3) cmp r4, ...
(5) movge ...
(6) cmp r1, ...
(7) movge ...
We cannot convert (1) to "subs" because of the intervening use of CPSR.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117950 91177308-0d34-0410-b5e6-96231b3b80d8
aliases installed and working. They now work when the
matched pattern and the result instruction have exactly
the same operand list.
This is now enough for us to define proper aliases for
movzx and movsx, implementing rdar://8017633 and PR7459.
Note that we do not accept instructions like:
movzx 0(%rsp), %rsi
GAS accepts this instruction, but it doesn't make any
sense because we don't know the size of the memory
operand. It could be 8/16/32 bits.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117901 91177308-0d34-0410-b5e6-96231b3b80d8
in their asmstring. Fix the two x86 "NOREX" instructions that have them.
If these comments are important, the instlowering stuff can print them.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117897 91177308-0d34-0410-b5e6-96231b3b80d8
consider it to be readonly. In fact, don't even consider it to be
readonly if it does a volatile load from an AllocaInst either (it
is debatable as to whether readonly would be correct or not in this
case; play safe for the moment). This fixes PR8279.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117783 91177308-0d34-0410-b5e6-96231b3b80d8
There were a number of issues to fix up here:
* The "device" argument of the llvm.memory.barrier intrinsic should be
used to distinguish the "Full System" domain from the "Inner Shareable"
domain. It has nothing to do with using DMB vs. DSB instructions.
* The compiler should never need to emit DSB instructions. Remove the
ARMISD::SYNCBARRIER node and also remove the instruction patterns for DSB.
* Merge the separate DMB/DSB instructions for options only used for the
disassembler with the default DMB/DSB instructions. Add the default
"full system" option ARM_MB::SY to the ARM_MB::MemBOpt enum.
* Add a separate ARMISD::MEMBARRIER_MCR node for subtargets that implement
a data memory barrier using the MCR instruction.
* Fix up encodings for these instructions (except MCR).
I also updated the tests and added a few new ones to check for DMB options
that were not currently being exercised.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117756 91177308-0d34-0410-b5e6-96231b3b80d8
just
.type foo,@object
will produce an undefined reference to foo. On the other hand, a file with
just
.weakref bar, foo
will not. It is somewhat hard to support both in MC since both statements
should create the symbols. It should be possible if we really need to by
adding to the flags, but hopefully that is not necessary.
With this patch we do not produce a undefined reference in any of those cases.
The assembly file needs an actual use for the undefined reference to be
present.
This is in preparation for a patch implementing .weakref.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117735 91177308-0d34-0410-b5e6-96231b3b80d8
This code had previously used 2*N, where N is the mask length, to represent
undef. That is not safe because the shufflevector operands may have more
than N elements -- they don't have to match the result type.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117721 91177308-0d34-0410-b5e6-96231b3b80d8
Allow splats even if they don't match either of the original shuffles,
possibly due to undef entries in the shuffles masks. Radar 8597790.
Also fix some 80-column violations.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117719 91177308-0d34-0410-b5e6-96231b3b80d8
operand and one of them has a single use that is a live out copy, favor the
one that is live out. Otherwise it will be difficult to eliminate the copy
if the instruction is a loop induction variable update. e.g.
BB:
sub r1, r3, #1
str r0, [r2, r3]
mov r3, r1
cmp
bne BB
=>
BB:
str r0, [r2, r3]
sub r3, r3, #1
cmp
bne BB
This fixed the recent 256.bzip2 regression.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117675 91177308-0d34-0410-b5e6-96231b3b80d8
With Python-2.4, Reader::read64 always returns (unexpected) long integer.
FileCheck detects failure on test/MC/MachO among '0' and '0L'.
CentOS5(aka RHEL5 clone) provides python-2.4.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117637 91177308-0d34-0410-b5e6-96231b3b80d8
* If we have a M or a G, reject sections without the type
* Only parse the flag specific arguments if we have M or G
* Parse the corresponding arguments for M and G
We ignore the G arguments and flag for now.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117608 91177308-0d34-0410-b5e6-96231b3b80d8
(like ARM) correctly. With this change, we can now match "bx lr"
because we recognize lr as a register.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117606 91177308-0d34-0410-b5e6-96231b3b80d8
Move the existing patching for undefined symbols so that all the patching
is done in the same function.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117570 91177308-0d34-0410-b5e6-96231b3b80d8
I'll work with Jim, Owen, and Bill on an alternative testing strategy until
the assembly parser is available.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117530 91177308-0d34-0410-b5e6-96231b3b80d8
- For now, loads of [r, r] addressing mode is the same as the
[r, r lsl/lsr/asr #] variants. ARMBaseInstrInfo::getOperandLatency() should
identify the former case and reduce the output latency by 1.
- Also identify [r, r << 2] case. This special form of shifter addressing mode
is "free".
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117519 91177308-0d34-0410-b5e6-96231b3b80d8
elements than the result vector type. So, when an instruction like:
%8 = shufflevector <2 x float> %4, <2 x float> %7, <4 x i32> <i32 1, i32 0, i32 3, i32 2>
is translated to a DAG, each operand is changed to a concat_vectors node that appends 2 undef elements. That is:
shuffle [a,b], [c,d] is changed to:
shuffle [a,b,u,u], [c,d,u,u]
That's probably the right thing for x86 but for NEON, we'd much rather have:
shuffle [a,b,c,d], undef
Teach the DAG combiner how to do that transformation for ARM. Radar 8597007.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117482 91177308-0d34-0410-b5e6-96231b3b80d8
sense, when the instruction takes the 16-bit ax register or m16 memory
location. These changes to llvm-mc matches what the darwin assembler
allows for these instructions. Done differently than in r117031 that
caused a valgrind error which was later reverted.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117433 91177308-0d34-0410-b5e6-96231b3b80d8
will accept versions that the darwin assembler allows. Forms ending in "pi" and
forms without all the operands.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117427 91177308-0d34-0410-b5e6-96231b3b80d8
on RIP relative relocations looks artificial, but this is a superset of
what we were able to do before.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117364 91177308-0d34-0410-b5e6-96231b3b80d8
The SPU ABI does not mention v64, and all examples
in C suggest v128 are treated similarily to arrays,
we use array alignment for v64 too. This makes the
alignment of e.g. [2 x <2 x i32>] behave "intuitively"
and similar to as if the elements were e.g. i32s.
This also makes an "unaligned store" test to be
aligned, with different (but functionally equivalent)
code generated.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117360 91177308-0d34-0410-b5e6-96231b3b80d8
do not double-count the duplicate instructions by counting once from the
beginning and again from the end. Keep track of where the duplicates from
the beginning ended and don't go past that point when counting duplicates
at the end. Radar 8589805.
This change causes one of the MC/ARM/simple-fp-encoding tests to produce
different (better!) code without the vmovne instruction being tested.
I changed the test to produce vmovne and vmoveq instructions but moving
between register files in the opposite direction. That's not quite the same
but predicated versions of those instructions weren't being tested before,
so at least the test coverage is not any worse, just different.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117333 91177308-0d34-0410-b5e6-96231b3b80d8
it isn't unreachable and should not be zapped. The check for the entry block
was missing in one case: a block containing a unwind instruction. While there,
do some small cleanups: "M" is not a great name for a Function* (it would be
more appropriate for a Module*), change it to "Fn"; use Fn in more places.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117224 91177308-0d34-0410-b5e6-96231b3b80d8
It doesn't look like anything is wrong with the checkin,
but the new test cases expose a mem bug in AsmParser.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117087 91177308-0d34-0410-b5e6-96231b3b80d8
weren't properly reflecting the OperandSize attribute
of the instruction leading to improper decoding of
certain instructions with the 66H prefix. Also added
a test case for this.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117084 91177308-0d34-0410-b5e6-96231b3b80d8
sense, when the instruction takes the 16-bit ax register or m16 memory
location. These changes to llvm-mc matches what the darwin assembler allows
for these instructions. Also added the missing flex (without the wait prefix)
and ud2a as an alias to ud2 (still to add ud2b).
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@117031 91177308-0d34-0410-b5e6-96231b3b80d8
1. A delay slot filler that searches for valid instructions
to fill the delay slot with. Previously NOPs would always
be inserted into delay slots.
2. Support for MC based instruction printer added.
3. Support for MC based machine code generation and ELF
file generation. ELF file generation does not yet
completely work as much of the ELF support infrastructure
is still x86/x86-64 specific.
4. General clean up of the MBlaze backend code. Much of the
tablegen code has been cleanup and simplified.
Bug Fixes:
1. Removed duplicate periods from subtarget feature descriptions.
2. Many of the instructions had bad machine code information
in the tablegen files. Much of this has been fixed.
git-svn-id: https://llvm.org/svn/llvm-project/llvm/trunk@116986 91177308-0d34-0410-b5e6-96231b3b80d8
